Today we go along to Bristol to meet Fred’s collection of minis, all needing a tune…..
Пікірлер: 32
@philhuggett47762 ай бұрын
Thanks AC for continuing to share the knowledge. Priceless stuff
@mr.buttons84862 ай бұрын
Thank you Sir
@Slack3rDav32 ай бұрын
a before and after drive video example would be wonderful
@ACDodd2 ай бұрын
This is very difficult to achieve.
@luismeixner21252 ай бұрын
AC, how do you check if the vacuum advance is working? little suck on the pipe whilst watching the advance on a strobelight?
@ACDodd2 ай бұрын
You got it, however you’ll likely to get fuel in your mouth!!! A vacuum pump is a much healthier way to check!
@Markycarandbikestuff8 күн бұрын
Hi AC great stuff, have subbed, quick question, will i be ok fitting an old 12G202 head on an 88 A+ 998 motor ?, it's a really nice big valve ported job, plan to eventually use this with a Kent 266 Cam, LCB and decent single box center exit system.
@ACDodd8 күн бұрын
Yes ideal you will loose a little compression but not a huge amount
@Markycarandbikestuff8 күн бұрын
@@ACDodd Cheers for that, seller did say head had been skimmed.
@supremefox23462 ай бұрын
What should be the target af/r on idle and when revving on a 1098cc with a stage 1 kit
@ACDodd2 ай бұрын
I offer training for those that wish to be able to tune carbs themselves.
@pablojimenez83292 ай бұрын
AC, How do you normally detect a leaking intake manifold/carb? What are the symptoms and how can you confirm the leak?
@ACDodd2 ай бұрын
Use a can of brake cleaner and spray it on the joints with the engine running. if the rpm changes it’s leaking. Revs rise carb is set lean, revs drop fueling set much too rich
@dominiccooper8102 ай бұрын
AC, any chance you could show how to by pass the ballast resistor? I’m fitting 1275 motor electric 65 d dizzy into a 76 mini scamp. It used to be 998. It did have a 3ohm coil but I’ve a 0.8 now cos of the dizzy. I’ve got no clue on wiring. Thanks
@ACDodd2 ай бұрын
Has your scamp got a ballast resistor in the loom?
@dominiccooper8102 ай бұрын
Hiya AC, thanks for the quick reply. I don’t know if it’s got a ballast resistor in the loom or how to check if it has. Thanks
@ACDodd2 ай бұрын
@@dominiccooper810ballast wire is white/pink. If the wire that feeds the coil is white you good.
@ColinSpencer2 ай бұрын
How do we get in touch with you and do you come to Lincolnshire?
@ACDodd2 ай бұрын
Send me a pm on Facebook messenger
@george50222 ай бұрын
AC, What voltage coil 12v 3A or 8v 1.5 A - on a blasted system ? its not specifically for mini but mgb.
@ACDodd2 ай бұрын
A ballasted system uses a 1.5ohm coil for a 4 cylinder engine.
@george50222 ай бұрын
@@ACDodd Thanks for the reply, so it should have a 12v coil with 1.5 ohm not a 8v coil 1.5 ohm
@ACDodd2 ай бұрын
@@george5022it’s not 8volt anything, it’s a 1.5ohm coil
@troypowell16712 ай бұрын
what leads do you recommend for a 08 coil with pertronix 59d dizzy and bp6 plugs gapped at 35tho and what ohm reading would be acceptable
@ACDodd2 ай бұрын
I use Powerspark 8mm leads having a resistance of typically 1.5 to 2kohms per lead.
@troypowell16712 ай бұрын
@@ACDodd copper core or the other kind
@ACDodd2 ай бұрын
@@troypowell1671not copper core
@nevhath2 ай бұрын
AC. Do you recommend fuel stabiliser with every tank of fuel. I'm running a 1310cc with your RS+ cam and a 45 DCOE Weber I always use Shell V-power
@ACDodd2 ай бұрын
How long do you leave it between using it?
@nevhath2 ай бұрын
@@ACDodd Use it regularly this time of year. Normally park it up when weather turns...(October time) I do add fuel stabiliser then when it's parked up over Winter. I use STA-BIL. I think on your recommendation..
@ACDodd2 ай бұрын
If you leave it longer than 1 month it needs stabilising. Stabil make a produce called stabil 360 which is designed to be used every fill up.