More excellence - keep them coming and quiet right that you are paid for your time and effort as your reviews are honest and trustworthy (as well as being highly watchable). Thanks for sharing as always 👍

Very nice job renewing and information on this laser. Can't wait to see more videos soon my friend. Forge On. Fab On. Weld On. Keep Making. God Bless.

As a (designer) blacksmith Joshua, you make an excellent computer operator / and presenter!! (complement😊). Your knowledge is outstanding!! Another fantastic video. 👏👍✊👌🙏 I loved the tractor on your little sons box! Brilliant 🚜👍

If you would like one of these desktop lasers here is Coupon code for you: store.creality.com/products/10w-cr-laser-falcon-engraver?aid=ytJoshua Coupon code: FalconJDL (30$ Off) FA80 (80$/80£ Off) 10W: amz.fun/poBB3 5W: amzn.to/3CIPZkZ Coupon code: 05ULJ9WS (5% Off)

Ending with the lil guy. NICE! Mine’s 32 now and man I miss that time HUGE!

Mr. De Lisle, I've found that different plywood produce different amounts of charring and tarring. I've found wonderful 1mm plywood from Finland that gives absolutely clean sides where you can't find any soot at all. I've found other plywoods where the smoke really hurts my lungs and the tar is thick. Specifically, you want to avoid formaldehyde - literally the chemical they use to preserve corpses. My point is, finding the optimal cutting speeds and pew-pews on sub optimal plywoods will still give you a stinky tarry experience. with regards, mattias

After having the creality falcon I want to try some other engravers. Some have linear rails and other designs that seem like they should be more accurate and repeatable than this design. Also some have belt tensioning screws to make that easier. Something the 3d printers have had for a while now. Some also have dual motors instead of the shaft to drive each side of the y axis.

Nice review. Lightburn has a built in centering function. You can centre an object to the work area or multiple objects with each other. Cheers

Really like the channel and impressed with your skills but the music is about 5X louder than the dialogue - I don't like it but if it is to stay, couldn't it be less intrusive and save me constantly adjusting the volume to hear the dialogue? Thanks

You made that wallet 🔥 great job

What would you recommend for cutting stencils out of Mylar, 1/16" and 1/8" Poly?

Nice review! What happend to the right frontwheel on the tractor?

id love to see how these device cuts out RC airplane airfoil and fuselage parts. I'm keen on getting one but want to see a demo. Any chance ?

I purchased this about a month ago and I can’t get it to work. I assembled it plugged it in switched it on it beeps but has never move an inch in any direction. I have spent a least 10 hours trying to get it working but without success I bought a laptop and downloaded lightburn and use the trial version but can’t get it to do anything is it a faulty unit? Tried contacting Creality but they are not much help,asking me have I connected it up correctly even though I sent them a video showing them it illuminated and beeping Any advice would be greatly appreciated as I’m totally frustrated with the situation and wish I had never purchased it. Thanks

I buy a welder.. Then find u got and reviewed same one. You get a 3d printer for review..its the same one I have 2 of...and now I buy a laser cutter, and bam, you reviewed the same one. Great minds...so it's back to me..I'll tell you the gadget I get ! A follow up on this would be good though ? ( also just bought your box designs).. The creality 10w is only 309 quid at the mo on creality site BTW. Bargain for a 10w, so bought air assist, enclosure and hex bed!

how is this laser working a year later?? thanks in advance

Hey, i can't find the lbdev file, will you please help me?

I’m looking at one of these second hand. Is it easy to upgrade the laser module later on if i want a more powerful laser?

This or the COMGO from your previous video?

I’m wanting for cutting I’m not so much in to engraving is this machine good for cutting and can it cut 10mm ply wood I would love to no what wood it can cut and speed ect with light burn I have around 450 pounds to spend on a laser cutter so would this be your recommendation for the price or is there better for the buck thanks

I looked for the feet to extend the height, the plates, and the blower, are they from a different source? Thx for the great video and coupon!

Could you tell me if there is a y axis roller for this please

I can’t get over the price! Ok, firstly, I wouldn’t recommend using 230v ac equipment on a truck, it will work and you will probably be fine but… those inverters can kill so please take care when routing cables. Maybe use copex or SY cable to give a bit of mechanical protection. Saying that, I don’t know how you plan to install this or what you will use it for so the above may be overkill but please bear it in mind. I wouldn’t normally say anything and my engineers used to use inverters to charge their drill batteries / power kettles etc but that was within the confines of their dry, warm cab, not out in the open with all those potential hazards. The other thing, what voltage is that control box? I always like to see 24vdc when it comes to the control side but have a feeling that that one is ‘mains’ voltage… Please look at its ‘IP’ rating if it has one, or just see how water could find its way in, another thing to think about if you will have to use this outside. Secondly, that capacitor…. I wouldn’t recommend using polystyrene because of the nasties it can give off when the motor gets hot or the capacitor fails, the capacitor will be absolutely fine rattling about, they are pretty robust. Lastly, please wear gloves when handling that wire rope, it’s fine when it’s new but after a while it will fray and cause nasty cuts. I use winches quite a bit and have a few scars to prove it. Yes, I didn’t learn the first time 🤦‍♂️ Great vid as usual, cheers 👍

How does this engraver compare with the Ortur LaserMaster 2, COMGO Z1 and LONGER RAY5 10W.

I believe the laser has a built in fan for smoke dispersal, but is this enough air supply to not require a separate air assist pump? Thanks.

Dropped the cash on one of these, still waiting for the bloody thing because Creality chose to use one of the worst rated logistics/couriers services. My 3D printer from them came faster with another service. Busy setting up the work space for all the expensive toys, would you say air assist is absolutely necessary? was looking at the enclosure for the laser but not sure if I should get both? Enclosure would however restrict the size of material I'm using so might be a no go. Do you have any updates/tips/trick on this model? Links? Great video.

can it cut through pine

ik this is a longshot, My Engraver Got burnt a while back while cutting a bunch of phone stands in wood, the wood caught on fire... Anyways I got all the parts I need besides the red Magnetic Lense/Sheild that attaches to the bottom of the laser module, I want to 3d print one but need to know the dimensions, more specifically just the height of the red shield, I can measure the laser module for the with, but cannot just guess the height because the beam needs to be focused. If anybody can measure the height of the red Sheild with a caliper and tell me how many mm it is i would appreciate it more than you could imagine!!

If I speak to Creality really politely and give them a boatload of money do you think they could send me a lightsaber? 😆 I reckon if I had one, a hammer and an anvil I could dispense with the software and just freehand my projects. (If the saber has a decent dimmer switch included)

Maybe provide some real links that don't involve Greedazon as not everyone agrees with the way they treat staff or charge more than the makers of some gear plus allow Dangerous and Counterfeit (*Recalled ) products to be sold. Some people do still have principles and won't feed the monster....

all good to do paid stuff - but you need to tick the paid promotion box. It's the law.

Please take a better quality of plywood 🙏 with the oil on its so ugly