Great Videos!

This is where I am, bed extraction...I think I'm gonna go this route with it & use some of my old lumber around here to build a similar frame...my long bed is still a long bed though, so it'll be interesting to see where the balance point is...

Really like those C10’s, going to be a fun truck!!

Great content, thanks for sharing with us! Just a comment about lifting the bed. I also work alone, picked the bed (mine is still a long bed) with one 2x6, a strap, and a shackle to connect to the hoist hook. The 2x6 was cut to fit snugly under the upper bed sides and ended up against the stake pockets for balance. I oriented the board vertically, not flat, but I think it’s strong enough either way. It was easy to adjust and balance with one person. I put it on a cart similar to what Paul built for his cab. Nothing wrong with Paul’s design except a bit of overkill. Thanks for this series, Paul! I’m a few years behind you but this series is really valuable!

Awesome bro! I enjoy your vids !

I really enjoy watching your videos, I have a square body project and am a one man show myself. I appreciate the ingenuity and planning as you tackle each step of your build. You’ve been an inspiration to me and spurred on my stalled build. Thanks for sharing your project with us!

Great videos! I like your ideas for box and cab removal. I'm hoping to take on a project where I'll put a rust free body on my 2003 Silverado.

Enjoying the videos man nice job

Nice Bro keep up the good vid's

Your show is going to be big congratulations I've been looking for something like this for so long

Nice job Paul,it's fun watching your videos.having built my 67 I'm thinking I should have video it too.keep it up man,look forward to your next one.

Awesome videos, really wanted to make something similar to remove my bed but the cost of lumber is absurd... I just hooked to the bed itself with some ratchet straps, worked good!

I wish I could go back in time and recommend to you some new casters for that Pittsburgh engine hoist. I just started using mine and quickly realized why they are so cheap. Some decent quality casters makes that engine hoist so much easier to roll around. Same with the Harbor Freight engine stands.

I’d definitely go get a few 1 inch welds at the corners on that after it’s driving. If you put any power in that truck the frame twist will be exaggerated. Might cost you $40 at a shop, strengthen in be 100%

A bro I have a question how long is the bed after you cut

What was the song to end the video?

Some welding? Just in case....

Can you weld the c notch bracket into place after bolting it on? Or is the frame hardened?

Was the c notch needed for the 5" lowering springs or the additional 2" blocks? I think I'm do springs only and is c notch necessary?

Forgive my ignorance, but what are C notches for? Greater flex under load?

Thanks for the time you put into making these videos. They’re great. Which c notch kit did you use?

Did your stock panhard bar bracket interfere with cnotch at all did you have to trim it down?

Aren't you going to weld it up? Pretty sure the bolts are just to get it aligned and clamped in the right place, then it should be welded

You might have answered the question. But with that c notch how many inches are you dropping the rear? Obviously I imagine you are changing springs? Thank you

nice to see someone do a decent video of the c notch install, I still haven't put mine in iv been procrastinating because im nervous ill mess it up but im good now after watching you do it. Did you put your brackets back in for the coil springs? you need them the keep the frame from flexing thought id mention it because I didn't notice them after you put the c notch in

Thanks for the Awesome videos!! We’re you afraid pulling the bed it would have bent the rails. Or was it not a concern. Thank!

What kind of camera over heats while recording? What camera were u using?

What a waste, I use one 4x4 balanced in the box. Must be a no brain engineer

Headache within 2 minutes with it bouncing sooooo much