Hope you enjoy the video! Please like and subscribe for more!
Пікірлер: 115
@billwatcher9321Ай бұрын
Ignore all of the idiots that give out negative comments. It's YOUR job. You do it how you want. I appreciate your taking the time to make these videos. The youtube "experts" are sitting on there ass at home and proably have never touched wet concrete or even published a youtube video. Please keep up the good work !!!
@jeffdeshongАй бұрын
Thank you 👍🏻
@smackmurph741421 сағат бұрын
I 1000000 percent agree with you too bro… if it wasn’t for people like you taking precious time out yo day to film stuff like this it would’ve been plenty projects I would’ve failed at cuz I use KZfaq creators for a lil direction In my own endeavors! Fuck what a hater gotta say!!🤷🏾♂️
@krafty6520 сағат бұрын
You did a damn fine job for 1 man, and the video was well done. Your grandpa is proud I'm sure, and rightly so.
@MrWaldorfian8 күн бұрын
Good job on the first pad square. I found that using a reciprocating saw without a blade on the forms help remove the voids. Not such a big deal on the inside edges that will have another pad poured up against it, but on the outside it would be a good idea. It costs a lot for a contractor do do the job because its a lot of manual labour. If you are willing to do it, you can save a lot of money.
@gilkennedy76388 күн бұрын
I would conciser repositioning the mixer and dump directly in the form to save some hauling
@strjourneys79194 күн бұрын
It's already done...nothing to "reconsider" 🙄🙄🙄
@bullpuppy7455Күн бұрын
@@strjourneys7919 Guess you aren't paying attention. There are still 11 more slabs to pour... Stay focused...
@strjourneys791913 сағат бұрын
@@bullpuppy7455 already done...
@jiggidyjam10 сағат бұрын
@@strjourneys7919it’s far from done genius
@MDC20208 сағат бұрын
@@bullpuppy7455 stay focused more like pay attention lol
@ryancoorey1587 күн бұрын
Don't let the youtube schmucks change how you operate Your channel. The algorithm is working. I subbed
@jeffdeshong7 күн бұрын
Really appreciate it 👍🏻
@uoobwatcher2 ай бұрын
There will always be armchair critics. I just bought that same mixer. Instructions sucked but I’m ready to start several projects. Good job.
@ThePainkiller36663 ай бұрын
I've been using my HF crment mixer for around 5 years now, just small things 2x2x3 pads, 10x12 shed slabs, when I need to do over 25 fence post holes. It's been holding up just fine, even built it a ramp that hangs on that solid bar below the drum so I don't have to empty the contents into a wheel barrow. Solid $189 purchase
@peteacosta10233 ай бұрын
Pls keep us updated on this project would love to keep seeing the progress!
@MegaTapdogКүн бұрын
You do you, I’ve done the same thing with my inexpensive Princess Auto mixer here in Canada and it has worked out fine. Did a 12x20 workshop floor for my shed and everything is fine, small expected cracks after putting my cj5 in and jacking but over all, great.
@jdtown658520 күн бұрын
Awesome freaking job, bro! Just what I needed.
@harolddobbins86453 ай бұрын
Looks good Jeff I’m going to keep watching Thanks one man can do it if he wants to 👍
@simpletruth99778 күн бұрын
Build a chute and set up closer to your form. That way, u can eliminate the wheelbarrow and the hauling. Don't pay attention to the ex-squirts. 😂
@lunchlady202322 сағат бұрын
I have the same mixer. It was cheap but works good for the past 2 years. I find it easier to to pour directly into form and I also leave running when I pour it out.
@rockharvey5787Күн бұрын
Wow that’s a huge job to do yourself. If it were me I’d buy one of those mudmixer machines and then sell it after the job is done. Good work!
@Outwest-qj5is20 күн бұрын
Nice job, I never thought about screeding as you go. That looks like a good idea.
@sybo106 күн бұрын
I've poured several of these through the years, I did an 8X10 x 4" using sakrete concrete bags and by myself, hell of days workout and it was much warmer, can't remember the amount of bags but it was like over 40 I think, one thing to note if you didn't is oil those forms so they come off super easy. I did another 10 x 12 one time and hired a cement truck to come pour it all. My sides had lots spots like yours where the concrete didn't settle properly, if you can find a concrete vibrator that would eliminate that just by running it around the sides. Over all nice job on mixing it yourself and it turned out great, good luck with the rest of them.
@jameskelly27776 күн бұрын
It looks fine bro
@alsouthern71903 ай бұрын
Good job Jeff. Are you going to drill holes and put rebar in between each pad to tie them all together? Going to be a nice floor for your building!
@jeffdeshong3 ай бұрын
Thank you and yes sir! They’ll all be tied together. Can’t wait for it to be done 👍🏻
@jasonbabila600610 күн бұрын
To raise the PSI with the concrete you can add more cement, as for the slump start out with adding a little water at a time to the consistency you think you’ll need so that it’s not too watery and it won’t take long to dry and harden.
@jimmybarraza5139Ай бұрын
Love your video! Thank you for it!!! It has all the questions I have for a do it yourself guy!!!
@jeffdeshongАй бұрын
Thanks for watching! Glad I could help 👍🏻
@jeffdeshongАй бұрын
Thanks for watching! Glad I could help 👍🏻
@jamesk74104 сағат бұрын
I think you did well and saved money great job!
@melinda5777Күн бұрын
You did good for your 1st one! ❤❤❤
@ericturner247716 күн бұрын
Looks like it turned out good! You save a lot of money when you're willing to learn and put in some work.
@grassabrutta13 күн бұрын
We just did the same thing this weekend. A 4m (13') x 3m (10') x 10 cm (4") slab broken into 4 equal parts of 1m (3.3') x 3m (10'), with inter-connecting 1/2" rebar (by way of notches in the form that will "slide" into the next quarter as we get to pour it). The rebar was sitting on 3" dobies, some of which toppled over. The entire form is on builders plastic. For the first quarter (which was in most areas closer to 6" deep) we went through 10 mixers-full, each consisting of * 1 bag of 25kg 42.N portland cement * 22 shovels of 0-32 mm ballast (rock/sand mix) I think we got approximately the same result in similar weather conditions. Key difference maybe is that we used a vibrator (which aids in moving the mud around inside the form and reducing honeycombing, but I think also brings bleed water to the top maybe a bit too early). Used an aluminium screed bar. Used magnesium floats. I didn't get to the broom since we needed to get a move on as it was getting late, and also the available brooms in the EU are a bit crappy. For the 2nd quarter this weekend, I will try to run a wooden bullfloat that I made in between the screeding and floating. Hopefully I can get to the broom. Dunno how to post a pic anywhere on utube to show my results, but would like to. Good to see some other poor bastard giving this a go. Shout out to @AJDIYNetwork who also posted a nice vid on the same method.
@jeffdeshong13 күн бұрын
Thanks for watching and the comment! Definitely a lot of work but worth it if willing.
@gregturner289910 сағат бұрын
Hats off to you for making it happen! Bummed that you forgot the vapor barrier, once enclosed your floor will sweat bad on humid days. But hey, you’re making it happen and that’s a really huge deal! Keep up the good work.
@jeffdeshong8 сағат бұрын
Thanks for watching. Definitely didn’t forget. Not needed.
@gregturner28998 сағат бұрын
Sweet! I wasn’t sure of your overall usage. I bought some property with a shop and if they had done that my floor would be nice and smooth, but they didn’t and it’s a real pain in the a!!
@happycasa86154 күн бұрын
Awesome job bro!
@jeffdeshong4 күн бұрын
Thank you!
@matty3320103 ай бұрын
Even Mike Day gets haters and he has over 30 years experience. Don't worry about those folks. If you want to save yourself a few trips with the wheelbarrow, try two dumps from the mixer into it. Also I will always do a test pull with my broom if I'm not happy with it I just hand float over it or bull float and I just want a little longer. Great video looking forward for the next one.
@jeffdeshong3 ай бұрын
Thank you very much! And some good tips 👍🏻
@andyparks612012 күн бұрын
@@jeffdeshong Mike Day is the Man.
@geraldpratt52523 күн бұрын
Nice work!
@BS.-.-3 күн бұрын
You have no vapor barrier under your slab. You can get water under the slab even with proper drainage.
@BoxTruckVagabond23 сағат бұрын
Great video. I'm going to pour my own footers so this was very helpful. I have a small channel and as others have said, I just ignore the haters. Actually, I thank them for watching. :) We (non-professionals) watch these videos to learn how to do things. As I said before, this is going to be very helpful. Thanks for taking the time.
@jeffdeshong23 сағат бұрын
Thank you! And some comments are so outa line, they’re hard to ignore 😂 but thanks for watching and I’m glad I could help 👍🏻
@mosesgomez762114 сағат бұрын
No matter your experience you did and excellent job .
@warpswede8 сағат бұрын
Nice work.
@MikeBMW3 ай бұрын
Good concrete work, Jeff! However, if you plan to put any type of weight bearing structure on these slabs, you would really need some footers in place. Otherwise, it's gonna be a troublesome experience. Generally, weight bearing load structures require a footing to be placed 12" below the frost line in your area. As @wisdomtrek1 mentioned, a monolithic slab would be the way to go with proper footers incorporated. A few cement trucks and a properly prepared base could be done in a day. Then, you could build whatever you want on top of it. Still, love your grit and tenacity as well as your videos! :)
@jeffdeshong3 ай бұрын
Thanks Mike! Yup already have everything planned out. For the metal garage I’m buying, this is actually extreme overkill. One of the main reasons I’m not using a cement truck is because they would have to drive over a septic tank so I can’t get one close.
@MikeBMW3 ай бұрын
@@jeffdeshong I should have know you had already thought a lot of this through. Carry on - looking forward to more! Thanks, Jeff! Always love the content! :)
@jeffdeshong3 ай бұрын
@@MikeBMW you’re the man Mike! I did originally plan on going the footer route. But I decided that it was going to be crazy expensive and a crazy amount of work. I really need a garage and I’m pleased with how my shed turned out so I decided to give a metal garage a go.
@MikeBMW3 ай бұрын
@@jeffdeshong I would expect nothing less than you already figuring the options. As a bonus, we now get to see a way to get this done which could be beneficial to many others. As for me, putting a small slab for a cover over my generator with the upcoming Florida Hurricane season. One never knows where the experiences you present could lead. :)
@bobgrim6735Күн бұрын
Same Harbor Freight mixer broke in 6 hours of use good luck
@crossbow353911 күн бұрын
I’m not a know it all and not in any way criticizing I drove a mixer for twenty eight years and can’t tell you how many times home owners put mesh in and leave it on the bottom of the concrete. That won’t do one bit of good. You have to pull it up as you go so it’s in the middle of the concrete. It looks really good also I hope all of those small slabs don’t heave differently and leave you with an un even floor. Looks like your gonna have a ton of water flow off that hill and under the slab. Again good job and good luck!
@lunchlady202322 сағат бұрын
Should be in upper third not middle.
@moshevivas11 күн бұрын
Awesome Job, ignore those negative comments.
@jeffdeshong11 күн бұрын
Much appreciated!
@kevinwilson666816 күн бұрын
Is it cheaper to buy bags of concrete or use a Portland mix. I ask because I am about to poor a slab in my barn. Videos like this are a huge help! Thank you
@jeffdeshong16 күн бұрын
From what I’ve seen, making your own with Portland seems to be cheaper.
@normbograham13 күн бұрын
In some areas, the local rock is not cool. ie: NYS shale. As such even in small pieces, it works as a base, but in the concrete it weakens the result, and is usually a disaster. So, the two are not comparable. Concrete companies might sell rock for concrete, but they might be further away (distance = cost). And in East Texas, there is not much rock. So, rock gets expensive, whereas local contractors might be getting huge trucks in, and it might behoove you to use them. So, it's a regional comparison. And not an easy answer, as you also have to consider the value of your time. ie, the neighbor was a contractor, and had more work then he could do, so, even he outsourced the concrete work for a giant garage he built. So, it's basically a local research project.
@grassabrutta13 күн бұрын
The issue often is getting a pre-mix that has strength close to what you can achieve by mixing your own ballast and cement. Buy the rock/sand/cement and roll your own. It's fun anyway.
@mine631212 күн бұрын
Looks good bro
@jeffdeshong12 күн бұрын
Thank you 👍🏻
@Slartybartfast46510 күн бұрын
Just stumbled over this video and had an idea while watching. Could you use a section of rain gutter and bypass the wheelbarrow all together like a cement truck. I don't know, would the rain gutter be wide enough for the idea to work, or something similar shape.
@jeffdeshong10 күн бұрын
I think what you’re talking about is possible
@user-pb8cy8oo6z2 ай бұрын
Curious for a dog kennel 20 x 15 you think 6 inches is to much or i can get away with 2
@jeffdeshong2 ай бұрын
6 would be overkill, but if you ever wanted to use it for something else you could. I personally would probably go 4
@workingmansrestorations70716 күн бұрын
Looks good. How are you going to keep the pads to hold together?
@jeffdeshong6 күн бұрын
Thank you 👍🏻 drill holes and rebar
@RobertJLessard8 күн бұрын
I'm a fan of doing things myself and as long as you tie them together with rebar and some of that concrete bonding stuff on the edges should be just fine.
@seeunow444 күн бұрын
How do you plan to connect the next pad to this one? With rebar?
@jeffdeshong4 күн бұрын
Yup rebar
@flavius2966311 күн бұрын
genuine question: if this is for a house, wouldn't the separate slabs move independently over time?
@jeffdeshong11 күн бұрын
Not for a house. And they will all be tied together with rebar. You drill holes and put rebar in when you’re pouring the next pad. No movement should occur
@thishex20 күн бұрын
I enjoyed your previous video and have told the story to several people of this guy who was a big enough beast to take on a large pad by himself and do a decent job on it.
@jeffdeshong20 күн бұрын
Hey really appreciate that 💪🏻 thanks for watching
@bensanders7392Ай бұрын
Whaddaya do if it rains on your sand? Is there any way to keep that dry
@jeffdeshongАй бұрын
I cover it
@rudykirsh91132 күн бұрын
You do a good job. & Kno wat you're doing.
@bensanders7392Ай бұрын
Man I'm about to get some land in TX and want to do this exact same thing, just a little thicker from tractor trailers and equipment machines.
@normbograham13 күн бұрын
East Texas has very little rock, and finding good rock, is difficult. I wanted two ton delivered (any rock), the companies are too busy with bigger projects (a year or two ago). They never even discussed price, they were just too busy, delivering hundreds of tons. So, the rock drama, changes the dynamics of concrete in East Texas. Even the neighbor contractor, used a concrete contractor, because his work was hopping. Certainly 2 years ago, contractors were busy with months of work scheduled. But, if getting a ton of rock takes a day of driving, that's a big problem, as it also increases the risk, and the wear on your truck. But if you need 8 tons, it's time to find another solution.
@TalksWithRyan10 күн бұрын
Big job but you’ll save money if you don’t mind the labor just spread it over a week or so and you’ll have it man . Good job
@zavomika83062 ай бұрын
20x30 40-50k cnd good luck 💪
@cdbbroadfield615412 сағат бұрын
By doing it yourself, I’m guessing is cheaper than getting a concrete truck. Just asking because that’s a lot of work for one guy
@jeffdeshong12 сағат бұрын
One of many reasons
@THE-APEX4 күн бұрын
Rebar needs to float off the ground half the height of the pour. Go in there with a hammer and it will be easy to demo. None of the rebar will be attached to the concrete. It will still be laying on the ground in the same place. Ask me how I know. 😢
@jeffdeshong4 күн бұрын
You couldn’t be more wrong. Maybe try watching again.
@andyparks612012 күн бұрын
That was a Ton of gravel?
@jeffdeshong12 күн бұрын
Yup
@alcrooks90953 күн бұрын
That's not a concrete Spike that's a 3/8 drive extension for your toolbox friend
@jeffdeshong3 күн бұрын
But works as a concrete spike lol good eye
@StateBoysLouisiana11 күн бұрын
:02 The pic of the slab would be a better thumbnail, you’ll get way more clicks
@jeffdeshong10 күн бұрын
Maybe I’ll try it
@rodneyball60172 ай бұрын
If you didn't figure it out, leaving one form board off until later at the end would have saved you a lot of moving of the concrete lol
@jjtrades718611 күн бұрын
It's always going to be cheaper product wise to DIY, but what's your time worth to you? Gotta factor that in. I used to try and do everything myself too but in all honesty, I'd rather pay an expert that will do it right and offer me a warranty so I can go do things I enjoy instead. But nice job none the less
@6lr6ak6Күн бұрын
I'd have done 4-2-1 mix, and id have filled the barrow before tipping into the form.
@jeffdeshongКүн бұрын
Thanks for watching
@andyparks612012 күн бұрын
if you formed up the pad, placed WWF (Rebar), placed the stone and hired a crew to place concrete....you might save some money actually, cost of tools , mixer, headache, good job though. A five man crew could that that entire thing done in no time with one load or two of trucks, you might be loosing money actually.
@jeffdeshong12 күн бұрын
Thanks but It’s going to cost me $3000 total for the 20x30 pad. Find me a 5 man crew that can get it done for cheaper. Not worried about time at all.
@rodneyball60172 ай бұрын
Cut it real close on large rock
@jeffdeshong2 ай бұрын
Knew I had extra. Will be getting 1 1/2 tons per pad for the rest.
@robertf7982Күн бұрын
I would order concert it's the same price and less work
@jeffdeshongКүн бұрын
Wrong
@willys50Ай бұрын
Second time you said 7 bags of this Portland., WHAT?😂
@jeffdeshongАй бұрын
?
@GS-zv3qn7 күн бұрын
Thats Portland cement, like Crete is short for concrete
@TagGeorgeКүн бұрын
Wow! I thought each batch would go farther then what they did. It is a shame you didnt have help. One or two guys mixing while the other guy pours prferably maybe even another mixing machine on hand. One guy looks good for maybe fence posts but above that looks like its too time consuming. Show this video to your friends and they should be ashamed of themselves for not helping in some fashion.
@jeffdeshongКүн бұрын
3 hours for a 6inch 8x7 pad? Not very time consuming at all. Could easily have 5 guys here. That’s not the point. Thanks for watching!
@Painintheknee2 күн бұрын
Me and my husband used the cement mixer from Harbor Frieght, and it did a good job. We put in a whole bunch of cement posts under the house for a new foundation for a pier and beam home. I shoveled and mixed the concrete while he ran the cement to the posts. And he said I didn’t love him.
@aday163712 күн бұрын
There will always be fools who agree with the way you're doing this. In fact, you did not raise the mesh and inch or so into the crete, your joints will require you drill and insert rebar to tie the squares together (or they'lll settle independantly), you run the risk of cold joints between "batches". At least get another to mix while you screed. I could go on, but we all know it just ain't that expensive to buy truckloads of redimix concrete, delivered. So what's the purpose of this self-torture?
@jeffdeshong12 күн бұрын
Tell me you didn’t watch with out actually telling me 😂 very obvious you don’t know as much as you think you do.
@setdown210 күн бұрын
@jeffdeshong ok here's my two cents...it took you 3 1/2 hrs.to do one pad and you still have to drill and install the rebar...so 11 more to do = 40 hrs.with forming new pads...as opposed to getting it done in one day with premixed...buy the crete and get some buds 2 or 3 and finish it yourself...do the math...figure how many yards you need x $125.00 a yard...give your "friends"a good lunch and then you owe each one a good work day...just saying... Anyway some tips... Your mix is too wet...wire needs to be pulled up...and drill three holes in each mating side of the form and put rebar in before you pour...you want a 3 inch slump...after yes keep it wet and then cover with plastic sheeting...good luck however you decide...🖖 P.S. ...I forgot if you want to guarantee that all pads stay level with each other just put in a keyway...