Impressive but you do have the oven witch seems to be one of the most important part of the job!!!!! Awesome content keep up the awesome work you do!!!!
@garforce22 жыл бұрын
Way to go John! great work listening to Chris
@Pickle1172 жыл бұрын
excited to see a mk7 golf headlight build. good stuff
@tyrannusspissamentum44237 ай бұрын
I baked mine like granny bakes pie lol...I seen one dude on KZfaq using his own DIY oven. It was an insulated box with a hot air gun blowing into it through a hole cut in the side of it. He even had a digital thermostat. Shit was pretty dope DIY. Minus the fire hazard.
@toddellis51972 жыл бұрын
I really enjoy your videos, especially the one where you broke down the 5-pin relay. I recently converted my 1995 Cherokee 2-door from 5x7 to 7" round headlights. The headlights interfered with the back of the housing for the turn signal/running lights, so I cut the back of the housing off, and installed led lights to the front of the turn housing. I used 2-5pin relays side by side for each turn/running light to be able to get the to work properly... First relay is basically only to run blinkers, and when the running lights are turned on, they go through the second relay, and blink opposite of the rear signals. in this instance, they work fine. The issue I'm having, is when i just use the turn indicators with no running lights, there is a ghost flash that occurs on the opposite side blinker just after the chosen side fires.... Happens on both sides. It totally works as it should with the running/headlights on... I know this probably sounds nutty, and there's probably a better way to do it, but i'm new to this game... SOOOOO My question is... 1) How can a blinker cause a ghost flash on the opposite side blinker? and 2) is there some sort of device or diode or something that I obviously don't know the name of, that will only let the circuit fire if it hits like 10 volts or above? I suppose it really won't matter TOOO much, because it really is just a baby ghost flash on the opposite side, But I would prefer my shit.... you know.... not to look shitty, ;-) Thank you brother for your help... Keep the great videos coming!
@ilyas57082 жыл бұрын
Plan on taking apart my stock mazda 6 headlights once i get my new ones. Take it apart, black it out and seal it back up.
@flyryde2 жыл бұрын
Dope, do it!
@timshields41482 жыл бұрын
This just goes to show how good your videos are. He gets the live view while we have to watch a screen. He’s paid attention and watched you do this multiple times. Great job! (Watch those small metal screws, they’re hot. Lol)
@justinbeigh752 жыл бұрын
Great job!! 👏🏻
@superspecialty5169 Жыл бұрын
You can find the staple or any metal with a strong button magnet.
@zepp3lin2 жыл бұрын
So can we DIYs use a normal baked oven that's big enough to put a headlight in?
@superspecialty5169 Жыл бұрын
I would want to see if suction grabbers would be adequate in pulling apart the pieces, then you could use heat protective gloves & a long sleeve shirt to keep from getting burned?
@SeanPamer2 жыл бұрын
Good job, Jon!
@flyryde2 жыл бұрын
Thanks buddy 👊
@jorgedelvillarl5396 Жыл бұрын
Hey men I want to put some jewel light on a Acura TL 2011 help!!
@Logan45499 Жыл бұрын
I could not for the life of me, get my 2g Fusion headlights apart.
@iWillFightYouInComments2 жыл бұрын
Hey Chris, Can you show us a custom headligth for a 2013-2019 Ford Taurus? There is no aftermarket headlights for this model. It would be really cool
@fragile20047 ай бұрын
Great video as always, i just got my first retrofit headlight projector instaled but i have noticed a wobble on the passenger side of my headlight, is this normal for a retrofitted headlight? thank you
@jasonmills4053 Жыл бұрын
My kitchen ovens minimum is 170degF and I baked them for 15 minutes and had no problem pulling them apart or softening the Butyl with 170 - not sure what others have discovered. How did you arrive at 220F?
@redzone5655 Жыл бұрын
Is it true that Porsche 911 dont use butyl for sealing but hard glue? I have heard that you should cut them using ultrasonic blade to open them up.
@isbsd4me Жыл бұрын
Could you give me some tips on how I would make my door mirror turn signal lights into dynamic turn signals. They sell replacement led ones for other models but not mine any help would be appreciated I have a 2007 Mercedes e63 amg
@aaronland1208 Жыл бұрын
Have you ever customized a set of 07-12 sentra lights
@nocluegarage6562 жыл бұрын
More videos mate loving the content
@Blackinterceptor9992 жыл бұрын
Where did you go! It's been two months and we're having withdrawals
@farrukhkhudayarov8621 Жыл бұрын
Hello. Since you are playing around a lot with electronics, can you help me to find remote which will control 3-4 relays, but remote need to show when relay open with indicator, so basically 2 way remote where I can see status of relay if it’s open or closed
@DerfOrNuffin2 жыл бұрын
Do you 3d print stuff like bezels and all that? What about printing lens and possibility?
@flyryde2 жыл бұрын
No I keep everything as simple and straightforward as possible. I spend more time on wiring than anything.
@DerfOrNuffin2 жыл бұрын
@@flyryde I was thinking about it. Trying to.figure out if its a route id like to go. I was vacum forming lens and bezels and small interior parts. 3d printing would give more custimaztion and better turn out rates. Love your videos been following for quite awhile. Really appreciate yoour responce.
@danielbaugher17982 жыл бұрын
@@DerfOrNuffin if you figure out making lenses let me know. i need to make some clear ones without the stupid cross hatch design for corner lights on a 72 chevelle
@DerfOrNuffin2 жыл бұрын
@@danielbaugher1798 From my research sanding and polishing, alot of it. And the right calibrations, right machine, right material. Im about to buy a 3d printer though. Going to try it. Theres a few people that have already done it forbtheyre projects on YT 3d printed. One guy did the lens to his corvette.
@DerfOrNuffin2 жыл бұрын
Depeding on the shape and complexity you could vacuum form or resin cast too. Older cars are pretty easy to resin cast. But once i get a machine id love to give it a shot. They have programs you can scan the lens area with a cell and it will plot it out on.a printing program.
@raultudor2000 Жыл бұрын
Hey there! I have to say that I am impressed by your knowledge and skills that you have. I do have a question for you. I have been struggling with some 2008 Audi A6 C6 4F headlights. All I could find online is that they are sealed from the factory with other then butyl rubber. It is called Permaseal. Ist there any way to open them without cutting through?
@kertiszman2 жыл бұрын
I have a gladiator with led headlights I wanted to install oracle Colorshift projector demon eyes on…after attempting to bake and pry off…it was a no for me. Would you be will to do it if I mailed them and paid you???
@osamatanweer8932 жыл бұрын
Would you recommend working on a light that has moisture in it? I accidentally melted the bulb holder in my Altima from an hid bulb and it got moisture in it. I was wondering if it was worth it to do a morimoto led projector retrofit and sealing the melted part with silicone or something. Or should I do the retrofit on a depo set?
@jevinsalvador83032 жыл бұрын
After cutting open a tail light, what would you recommend to seal it properly without any leaks ?
@TheKomar9242 жыл бұрын
Nice!!!!
@miltong49232 жыл бұрын
Or you should do BMW light
@miltong49232 жыл бұрын
You should do a video about 328d BMW????
@miltong49232 жыл бұрын
About Light
@aprentiss98332 жыл бұрын
Where the new videos at??
@isimongames53472 жыл бұрын
Off topic from the video but, I’m looking for a small led switchback strips to put behind the door handles of my 03 f350, they can’t be longer then 3”, any recommendations? Thanks!
@gabrielscotto19272 жыл бұрын
Hi how are you, did you work in Volkswagen?
@Doogleraia2 жыл бұрын
What were those headlights out of? Looked like some of the reflectors had almost the exact same shape as the ones in the Mitsubishi Airtrek, or close to it rather.. long story behind my curiosity
@yeahnoway1112 жыл бұрын
Grand Cherokee WJ
@mitchmillington81832 жыл бұрын
What would u do to adhere drl strip if I’ve gta put in back in the oven when I seal it back up as wel as stickers are they fine or fall of
@fablighting78842 жыл бұрын
Grip em and rip em Jon😎😎💚💚
@masoudmontazery907 Жыл бұрын
Good luck...
@benjamincole8677 Жыл бұрын
Do you still answer this I got 2017 keep Cherokee question for headlight this is Ben painter from Yucaipa
@HillbillyHydrographicsVinyl2 жыл бұрын
I just dip mine in liquid panty remover and they just fall open👀
@flyryde2 жыл бұрын
Cheater
@brianlow72352 жыл бұрын
What vehicle is this for?
@flyryde2 жыл бұрын
Jeep WJ. Jons content is all about those 👍
@Term808_2 жыл бұрын
Anybody ever think of sticking an lcd inside a housing ? 😂
@oldredun5 ай бұрын
More hurting people's feelings 🤪🤣🤣🤣🤣
@superspecialty5169 Жыл бұрын
You can find the staple or any metal with a strong button magnet.