Jump on it quickly because it gets expensive fast!

Did you change the output/ input speed sensors? If you did and it's still throwing this code, then it's highly possible you may need transmission work at this point. You may have fried the clutch bands in the transmission. But check your output/ input speed sensors first.

You see that's exactly what kept happening to me and I would also pull over turn off the truck and restart it and then I'll be able to drive again but the problem with that is that the module just gets worse and worse and then eventually it will grenade your transmission so I highly suggest you change that module as soon as you possibly can and learn from my mistake.

@@svcruza well the part is in and seems to driving better so far but haven’t put that many miles on it. My connector that I pulled out was white which was confusing bc I have never requested any transmission work to be done on my truck. Appreciate you sharing the content.

P1D93 Dodge Code - Incorrect Gear Ratio Clutch 5 Defective need help

@@andrestar9390 if you are getting this code or anything transmission related, I strongly suggest you change the input/output speed sensors and your shift module asap otherwise it will grenade your transmission like it did mine! Dont wait like I did...do it now if you can and save yourself a ton of money.

It was called the shift module? I need to replace mine. Just started getting the code.

Suena raro q así hayas solucionado el problema, ya q el código po734 está relacionado a cuerpo de válvulas o fugas internas de presión. Ya sea por desgaste de pistones válvulas o discos del tambor de 4a velocidad. Saludos

Yes, my light went off but it came back on about 2 days later.....same code. I thought I had more time to get the module swapped out but i was WAY wrong on that assumption. As a result, my procrastination costed me thousands of dollars in the long run. Since the rebuilt transmission was installed, that code is gone.

@@svcruzahow long did you drive it/ take to swap the module before the catastrophic damage and what was damaged ?

It was the last alert my tcm could give me before the transmission was trashed. Ultimately the bands on the clutch couldn't function properly anymore so the truck kept acting this way as if in limp mode. What ultimately grenaded my transmission was that sudden downshift from 5th to I believe 3rd or 2nd at 70mph is what killed it. All because the module was going bad on me and frying my clutch bands. It went from cheap to expensive real quick.

The solenoid pack and my procrastination was the cause....I waited too long to address the issue and I paid the price for it.

I have a Ram 3500 68Rfe

2014

Did you also replace both input/output speed sensors?

@@svcruza yup

Did you replace module/solenoid pack? Really don’t want to buy a new tranny lol. Getting the 0734 code

@@reelknottybassin4830 I replaced the whole valvebody assembly with the solenoid. Alldata diagnostics points to some part of the valvebody, solenoid, or the transmission friction discs AKA full rebuild.

My truck is an 07 and I ran into these problems and failed to address them in time. Since yours is an 06 I would strongly recommend replacing the shift module in the transmission and the input/output sensors on the side of the transmission. With yours being an SRT8, your repair bill will be significantly higher than what mine was so I would address these issues immediately. The cost of a $500 part is better than forking out $4k.

@@svcruza thanks broo !!

@@svcruza when u said shift module on the transmission u mean tcm right ? Or an fuse ?

Transmission Control Module. I was also told it's the shift module but everyone has their way of saying it...lol I pointed it out in the video so you know what it looks like.

Alr, i understand now bro, thanks. Im on the way to do it !

Sell it...🤣🤣🤣

Is it an automatic or manual transmission? Any check engine light codes? Care to elaborate on it being "stuck"?

yes, I drive the automatic code P0734, when I shift gears 1-2-3 to 4, it throws 3 again and falls into the code P0734, it goes backwards, only it does not go forward, the gearbox remains in 4-5

yes, I drive the automatic code P0734, when I shift gears 1-2-3 to 4, it throws 3 again and falls into the code P0734, it goes backwards, only it does not go forward, the gearbox remains in 4-5

?