Great step by step. Thank you. I just finished doing our floors with LVP. Pretty much the same process except for working vertically or horizontally. 👍

I used this product and while it went fairly well there are a few things I can recommend. I used a standard 50% overlap to stagger the joints, looks better to me, everything terminating at the same spot isn't appealing. I used a lot more adhesive and silicone sealant, I used twice the amount provided, the working area was a remodel and the surface wasn't always perfect so the adhesive would need to be thicker to span the gap in a slightly out of square corner or low spots in the wall, this allows the Palisade to appear smooth while still having good adhesion. Your project may be more square and go well with whats provided. I applied silicone sealant to the joint and then made a bead on the wall that came all the way to the back of the tile before installing the next piece. This was because many of the panels would have a small chip missing out of the tongue corner leaving a very small gap (very minor shipping damage), basically there was enough sealant that it sealed between the wall and the panels along with the interlock. The process of using only the corner molding to have water run down and saying you can put silicone there isn't wise, you should for sure and use plenty, water leaking behind and getting trapped will lead the mold, you need to make sure your water tight.

Awesome step by step! Can’t wait to try this on my 2nd bath.

Excellent teacher! It’ll make the difference between renovating or not renovating as labor is expensive and I can do this myself!! Thank you 🙏

I think it would look so much better if the tiles design lined up I am doing my shower now and that is what I am focusing on. I guess I am OCD. But thank you Skip for all the videos that allowed me to do this myself!!!

This is a great step by step video. Thank you for all the hard work.

I used handheld automotive glass dual suction cups to hold and position the tiles. Much easier than latex glove for grip. Thanks for the video instruction.

Really great video. Thank you!

Busy pattern but great concept and great for diy and to freshen up a bathroom.

Superb video with all the tips you require. Thank you

Thanks. Excellent demonstration!

i use these palisade shower tiles all the time. probably have done 300 tub walls with these...everything you did was correct except not staggering them looks horrible.

Very helpful video. Thank you!

I wish he could redo my shower 🙈 this is perfect 👌🏼

Great instructions!

I would have ripped my first row a little bit so there wasn’t such a small piece under the window, and at the top of the shower…and it NEEDED to be staggered..😩🤦🏽‍♀️ i couldn’t handle showering in that with the seems all the same, and the patterns being so different 😂but that’s just my opinion and my taste. I’m sure some people wouldn’t mind that layout, but I definitely would have done the “brick lay” pattern if it were my own shower, or for a client, unless they specified otherwise. I want to try these out in a couple months when I move!

Very informative video 💯🌟💜🌟💯

Nice job. Thank you

Can I just hire you to come do my shower?!! Nice job!!

What if the wall is uneven? The old stone tile is higher up and lower in spots like it wasn’t laid correctly.

Only critique I would have is to rip your first run of tile to where you wouldn't have such a small sliver under the window and just under the ceiling. Looked like a nice product though.

Did two rooms with this,. Hint. When laying out each row, sometimes they are not level with each other. I would add a "dry piece" above each joint and it would then reveal a piece was not pushed all the way in place.

@5:53 you point out a space left for toom to connect the last piece. You should say how you measured that so its the right length. Great video and thanks for posting!

Hi! What type of glue can I use? Thank you

Would like to see a video using this product to make a shower niche.

Can this be installed over paneling?

Excellent demo! Please have a display board with samples at Lowes and Home Depot. Neither have any in stock or on floor. I would add a bead of mildew resistant silicone at the base of that first tile sitting on the tub rim. That is where maximum water collects. I'm surprised you don't have an edge strip for that section. Thank you for an exceptional video!

Why didn't you stagger the vertical seams?

This is nice

I'm looking into prepping my cement board, did you use RedGard? Or what type of polymeric coating did you apply?

We have plaster and lathe in the bath surround - walls are in great shape. Wondering if these tiles could go right over top OR is it prudent to add some sort of water barrier? I know you don't in your video but just wondering...

I noticed he did not caulk the vertical joints --- is this recommended?

Can these type of tiles be painted?

I think it would look better if the joints were overlapped. Is this possible?

Very nice but is there a reason u didn't stagger the joints

Can the tile be placed in a herringbone pattern or used on bathroom floor?

Looks great! What if the tiles don’t go all the up to the ceiling but stops 3/4 way up. How can you level the difference all to apply the panels all the way up?

I am using these tiles to do a backsplash on the wall above the shower surround. I have J trim to finish the edges but it doesn’t seem to be wide enough to accommodate the tiles. Any suggestions?

Shouldn't you also put sealer in the tracks to keep moisture out ?

What adhesive are you using to glue them to the wall?

Recommendations on what to put on drywall before installing?

I just purchased the Palisades tiles. I'm having a problem determining which edge of the tile is the tongue. There is no pictures showing exactly which is the tongue. All sides of the tile have what one would call a tongue. I'm assuming the edge with the tongue? is in the center position. The other tongue is on the end. It would have been simple to take a picture of both sides and define which side is the tongue, especially when you must install the tongue up. Anybody know the answer

If you measured from the inside lip of the tile to the inside edge of the trim, how were you able to achieve a gap to be able to slide the tile into place?

I must have overlooked it on the website but what type of adhesive do you use to attach over drywall? Thanks

So with these tiles is it not required to put that little spacer at the bottom of the rule so it's not flush with the tub? All the diy's I've seen said to not place the yikes flush with the tub... Im not sure why though.. does it depend on the type of tile?

Do you recommend this gif shower floors as well? I have travertine tiles (small) on shower floor. Want to redo the whole shower and don’t think paint will hold up as well. It’s used a lot! Thx!

At 6:00 you slid that 1st row over and centered it. That created small gaps on the inside corners now. Is that ok?

Can you put this over a shower bench if so how will the water drain over the edge if you put a piece of trim on the end.

Want to install in RV shower - are these tiles rated for extreme temperatures?

Does the inside corner trim piece need silicone in it before placing the tile inside it??

I’m having trouble understanding the difference between the L trim and the J trim. Can someone clear this up for me? What is the J trim for? Do I need both? Thank you!

How good is the adhesive. Will i have to worry about the adhesive bondage giving way over time?

We have a walk in shower in our master bathroom. Can these be used on the floor or are they just for the walls? We currently have tile on the floor and a drain in the middle.

I had been researching Dumawall but now come across this (same person hosting video). What distinguishes Palisade from Dumawall?

Plaster?

Why not stagger the tiles? You'll always see the joints if not plumbed.

Should you remove the old caulk where the tub and wall/tile meet before you start?

Wouldn't the L-trim around the bottom window sill prevent water from shedding because of the slight lip?

And this can be covered over existing tiles too?

What glue do you recommend? Loctite ? Liquid nails or other?

do you add a trim piece to the top or do you just caulk it?

What material are they made of?

Does anyone else’s trims design flake off or come off with tape?

Can these be installed over Kerdi board in a shower?

If your tub is not level, can you use a trim along the bottom to seat the bottom edge into then apply silicone to seal it? That would take up the difference from one end to the other without having to make angled cuts on the tile to get them installed level. Really want to know because I plan to install this on a tub on a house that's over 100 years old, so it's cast iron and not something I am going to level.

Can this be removed without destroying the tile underneath?

Why not stagger the seams?

Why not stager the joints?

Is this a cementicious product or plastic?

Trying to find someone in San Diego who can install this? No one seems to know about it?????

I think the seam looks pretty bad. It would be better to have staggered them but glad to know I’m not the only one with the wild idea of putting flooring on the wall.

welp, honey-do list!

what is the adhesive? you don't show what is the adhesive

It would have been nice if you actually showed how you put the end piece in the track and got it to clip it in in the lip at the same time.

please makes sure wall is plumb and level before you even begin

What do you recommend using for them to stick to cement board? Liquid nail?

Not a fan of the color of this set but looks simple and came out looking pretty clean I bet it was a headache trying to match what was already in the box

That joint between those 2 first tiles weren’t even tight though 😳🤔😂🙈🤷🏻‍♂️

Should’ve started with a half tile to eliminate the little piece of the top

You absolutely have to glue the connections or water will get behind them and mold will grow. Don't kid yourself it's not an option.

Horrible tiles, but excellent demo. Thanks you.

Excellent video explanation... but Terrible choice for tile color / layout!

This looks horrible, you’re supposed to offset the tiles

Is what it looks like…Junk.

Stupid idea wtf

That looks horrible!

From my experience, having the rubberized underlayment gives you zero time to slide the tiles, so better have them almost in place first. On other substrate it was easier. The glue holds well and i liked using the corner channels, gives you a little room to move. The tiles are well made, not a single edge chipped or broke from installing, overall it's good, but the the price is a bit high.

This little kzfaq.infoUgkxVoi3B4CB6Oygq1-vo4OTL1M_M5JkrXif tub works perfect in our 6 x 6 shower and is easy to get in and out. Also easy to drain.