How To Repair Parrot ANAFI drone : 00:08 Preparation before any replacement 02:25 Chapter 1: How to remove the arms 06:09 Chapter 2: How to replace the motors 10:52 Chapter 3: How to replace the arms
Пікірлер: 111
@TheMV199210 ай бұрын
Thank you, I successfully replaced an arm with no previous experience doing any electronics repairs before!
@richardsoniv3 жыл бұрын
Would be nice if you include the Gimbal repair. A # of Anafi users have loss their camera following a crash, requiring them to dissemble the gimbal section to check for cracked pieces.
@FirstLast-ym9vs3 жыл бұрын
Awesome Thank you so much. Followed your steps and successfully replaced both rear arms, my anafi flies like new again!!!!
@ersvideo53952 жыл бұрын
There's a massive omission in this video. My version of the ANAFI has the GPS cover fixed on by two more screws that aren't shown here. Any they are small screws - Torx T1 or T2 (don't know yet until my Torx set arrives from Amazon and I can try and remove the screws) But until you can remove the GPS cover you can't get at the arm fixings. So on later models you need an extra Torx size that isn't mentioned here.
@clicu Жыл бұрын
Had the same issue, almost broke the cover before noticing the extra screws
@HoverTime4 жыл бұрын
I'm ordering the super long term extended warranty that covers all repairs.
@piotrex13755 жыл бұрын
My Anafi has drowned yesterday in a lake.....I found it on the bottom and.....after 24h with hair dryer(without opening it) It's ALIVE !!!
@user-Chikotillo4 жыл бұрын
Good to hear its alive! how did it end up in water? Was it your fault or Anafis?
@piotrex13754 жыл бұрын
@@user-Chikotillo I was trying to land on the hand of my friend while we were all on a Yacht
@LUKE_XONG3 жыл бұрын
Thank you, just saved my dron
@paulhatcher14904 жыл бұрын
Thanks for the video. To all naysayers you can buy mechanical parts from Parrot from their website, unlike many other drone manufacturers. This video is intended as a "guide" . You still need to have some mechanical/modelling experience and something between your ears in order to repair successfully.
@fabthefab754 жыл бұрын
yeah right... but your beloved "guide" is missing the most important AND difficult part. Removing the main board and most of all, putting it back. With the most fragile connector i've seen in about 40 years and the most piece of crap rubber shock absorbers money can buy. Probably an info your "something between your ears" has missed...
@inbetweenland43953 жыл бұрын
Well I have a broken rear leg and I am following this guide. At 4.47 mins you have to push the bolt out. They introduce another screwdriver which they don`t give you any info on to what it is size or type, it looks as though they turn before pushing the bolt through. So up until I find out what this is repairs have to stop as this bolt is solid and will not budge. As for their website I did try to buy a mechanical kit but as soon as you try to pay without using paypal it is downhill. More importantly no drone company in Scotland will touch this drone send it to Parrot they all say, problem with Parrot is they will not do the repair. I would also like to point out that there has been many questions addressed to Parrot on their official video and they have not responded to one, which is a bit of a surprise at I thought since Parrot do not have a customers support in the U.K and refuse to fix your drone they may be interested in answering questions in this video. This is not that complicated to fix if the video provided you with all the proper tools which they do not, even harder when they refuse to answer questions on the video. Parrots consumer advice wing is appalling more than happy for you to buy their product but cannot be arsed to help you fix it when it goes wrong. Best bit of advice that I can give is do not buy a drone from a company with no customer support in the U.K Parrot is that company. My next drone will be a DJI as everybody fixes them in Scotland which stops you going around looking for nameless screwdrivers from a company who cannot be arsed answering basic question on their very own You Tube video
@MrAllenMo5 жыл бұрын
Hoping to never have to do this, but thanks for the reference video. Very clear and concise.
@kushking5354 Жыл бұрын
Ohh yeah very good am i just magically ment to know how to disconnect the 2 additional wires on the back of the motherboard For an official parrot video i have to say quite a let down
@cartechniques101icanfixtha24 жыл бұрын
Ur video is incomplete you fail to show how to put the loading spring and small retaining clip back in during the assembly of the amateurs. What the hell
@andrewknapp63995 жыл бұрын
What about the back side of the main board where the sd card holder is? Suddenly at 2:27 the main board is lying on the table!
@bdanuw4 жыл бұрын
@Parrot Please provide that information. Not sure about what connector is meant to come.off and how so I don't break any connector please!
@elidotson95614 жыл бұрын
it says removed for visibility in the video
@fahrbierde5 жыл бұрын
Hab ein Ersatzbein bei www.dronivo.de (super Service, schneller Versand) gekauft und Dank dieses Videos war der Austausch nicht so schwer!
@jonasbrobergburmehl32243 жыл бұрын
Perfekt 🤩 thanks😍👍
@GorillamansGarage5 жыл бұрын
Very thoughtful.
@KevinPinto3 жыл бұрын
I followed the instructions and when I attempted to unscrew the arm hinge screw, the head stripped completely. Any ideas? Nothing is sticking out of the plastic that I can grab. I have tried various tricks but none have worked so far.
@awesomecat33455 жыл бұрын
Man i wish they made a video of how to repair the parrot jumping night drones
@pedro142755 жыл бұрын
the jumping sumo is similar, the tutorials of the jumping sumo are available in parrot youtube channel
@awesomecat33455 жыл бұрын
@@pedro14275 yeah but they are different from the jumping sumo so yeah
@awesomecat33455 жыл бұрын
@@tcterrence try waiting for the signal of the drone it takes 5 minutes to find it
@awesomecat33455 жыл бұрын
@@tcterrence try using another device with android updated or a tablet
@ducaapple5 жыл бұрын
Molto interessante!👍🏻
@MagicBiscuitShow3 жыл бұрын
After a crash, I am not able to align the camera/gimbal back to the proper position. I've adjusted the camera up to the maximum of 5.0 ... but still need, the equivalent of, 2.0 or 3.0 more points of adjustment. I have tried "resetting" the drone, as well as other things, but when I try to Calibrate the Gimbal, I always get the message: "Place done on a steady surface and click OK." Also, when it tries to do the calibration, it doesn't move properly as does my other Parrot Anafi. And I've also tried doing it with my other Controller ... same result. So, this makes me think that there is something wrong with the gimbal. Do you know if when replacing the gimbal if the motherboard must be replaces as a 'matching' set? If so, do you have any idea where these may be purchased from in the U. S. ... or a good repair company? Thanks
@johnjansen10023 жыл бұрын
I am also looking for repair parts so frustrating. Did you ever find any help
@cmdrefstathiusplacidus9003 Жыл бұрын
anafi thermal suddenly went into emergency landing then it fell from the sky then it said engines have cut out, the obvious thing that is broken is the plastic brackets on the camera, do you have instructions and parts so I can repair it? I believe the camera itself is still intact other than the small micro cable came unplugged. The wire with the sections of shrink wrap is still in tact. what are my options? Thank you.
@bernardodiazdelcasti5 жыл бұрын
Hello, the Blue light on my anafi doesn’t turn on what can I do?
Any other videos on how to repair? Such as drone not powering up?
@farrighi3 жыл бұрын
I have problem with camera, do you have any trick, probably sand in the rotating system. Thanks for your help
@x-droners44105 жыл бұрын
I think we should first teach people how to use anafi instead of teaching people how to split anfi. In fact, you simply did not provide any repair parts that consumers can buy.
@touchmeonmynono51424 жыл бұрын
BRO YOU GOT BURNED
@inbetweenland43953 жыл бұрын
At 4.47 mins in this video after at the start you bring in another screwdriver which (this is what I think ) you use to turn the bolt before pushing it out to release the arms. What screw driver is that ? I have followed this video to replace a rear arm and that bolt which holds the arms in place will not budge ?
@gabadventures71274 жыл бұрын
Do you have to take the whole drone apart to replace one arm?
@ddpp34922 жыл бұрын
Yup
@haristonmarreiros72843 жыл бұрын
My Anafi is having trouble maintaining altitude as soon as I take off sometimes he just drops altitude so fast he hits the ground. Can give you a clue as to what might be causing this behavior. Remembering that he's not having trouble holding the position just his height. Thanks.
@monogerman9395 жыл бұрын
Ok, Ok... Where can we purchase the so needed ANAFI MECHANICAL KIT??????
@silbay5 жыл бұрын
lol they are out of the consumer drone business so good f'n luck, Skippy. Still gotta love that memory card holder from a 1990 cell phone. 1 cent cheap chinese crap, yep real build quality
@@silbay . Another paid DJI troll?? www.cnet.com/news/parrot-anafi-thermal-drone-pairs-flir-thermal-and-4k-cameras-for-1900/
@cartechniques101icanfixtha24 жыл бұрын
Amazon has the complete mechanical kit for $100 right now but it's not OEM so I'm not to sure about the build quality.
@MrWeighloss5 жыл бұрын
where dose the gps plug into?
@bohemianrover77875 жыл бұрын
David Woods seriously
@bderx65084 жыл бұрын
@@cartechniques101icanfixtha2 hey could you be more specfic possibly I cant quite find it
@cartechniques101icanfixtha24 жыл бұрын
@@bderx6508 what's ur email shit won't let me send pics because it's a no reply via KZfaq or hit me up @ joshlunsford2000@gmail.com
@cartechniques101icanfixtha24 жыл бұрын
@@bderx6508 I posted a video look up parrot ANAFI GPS motherboard location
@paulaseverino41624 жыл бұрын
@@cartechniques101icanfixtha2 i'm done except that antenna wire from the gps.. i didn't undo it.. i came off and i have no clue from where? can you send a link to that video?
@ekognaG5 жыл бұрын
Please make available in the US
@paulaseverino41624 жыл бұрын
19:59 it says "place the gps board and fix it".... well ok but where does the wire get connected... they don't show that... can anyone help?
@sajchoudhry72874 жыл бұрын
Anyone help
@armenmty2010 Жыл бұрын
How to fix the zoom? The zoom button doesn´t work
@AdityaDPutra-mu8mi11 ай бұрын
where do i attach the gps connector cable?
@samotrasin62 жыл бұрын
hello everybody here, what if we plug the 4 motor connectors and the antennas into wrong socket, will it still work? My anafi keep flipping before take off, and i dont think it's the propellers. thank you
@DavidGarcia-ru5pl3 жыл бұрын
I have the arm of my Anafi broken but also it doesn’t start. How should I start repairing? Thanks
@liberc10842 ай бұрын
What is the size of screwdriver in 4:43?
@joseariascarrasco9253 Жыл бұрын
Hola chicos necesito ayuda,la cámara de mi anafi no da señal de imagen,alguien me puede ayudar
@connorbax77672 жыл бұрын
Parrot Anafi, no crash, up to date firmware. Starts up normal, but the gimbal fails to initialize. It twitches in one direction then stops. It will then repeatedly try to flick back as though trying to intialize again every once in a while. Any ideas?
@UnderwaterGeek0073 жыл бұрын
hi there, where can i get my drone fix?? try my self but noo luck!!
@user-Chikotillo4 жыл бұрын
Great drone! But i hope I would never have to do this kind of repair, these motors should last, they are brushless after all
@jaimemiranda8252 жыл бұрын
What tool is used to remove that white bolt with clip on it??
@bonnielariviere63704 жыл бұрын
Drone crashed sigh,arm beside camera cracked.can I just replace top or is it the entire body? Any one.also I see rubber type bushings between camera arms do they just pop out? Anyone?
@richardsimmons64704 жыл бұрын
Where does the GPS GO No video shows this
@KaleneNieves4 жыл бұрын
How do you replace SD card connectors?
@philippetouzain67464 жыл бұрын
comment remplacer la nacelle et la caméra sur mon drone anafi merci ?
@pedro142755 жыл бұрын
i have a problem with the LED light
@rx43554 жыл бұрын
介紹自己換零件可是卻買不到零件,鏡頭壞掉都找不到修理......
@inbetweenland43953 жыл бұрын
I have bought a rear leg from Dronavi GmBh and successfully installed the part and now my drone flies again
@alexuskhan63954 жыл бұрын
Whats with camera? it not Wayne Worlds "Camera 1, Camera 2, Camera 1, Camera 2, Chapter ends and the music? just why? can you not explain while you go? and this is the official channel?
@stephenspilberg28555 жыл бұрын
My anafi doesn't fly but the blades spin... I changed it tho ... will that be the reason ?
@cartechniques101icanfixtha24 жыл бұрын
I would try an match the prop arrows to the motor arrows I got them backwards once an the motors would power up but would not take off I would check that if you haven't already
@AECRADIO14 жыл бұрын
Check blade/rotor rotation. Each motor has two triangles on the rotor, indicating rotational direction.
@AECRADIO14 жыл бұрын
This would be a better guide, if we were allowed to include images in our replies.
@crisdeodates4 жыл бұрын
Anyone have any idea about what those repair tools used in this video are?
@StayPeakedGames4 жыл бұрын
A t5 torx screwdriver and a pair of angled tweasers
@bjnslc3 жыл бұрын
The connector holder is too delicate to service without a spare onhand.
@baalatcloudel44823 жыл бұрын
My daughters name is anafi
@jefftwocreates4 жыл бұрын
yeah, the directions were not very good. I followed it step by step and assembled my new legs, and after I put it all together, no my SD card reader won't read, and I can't record videos. I love the Anafi, but this was a very bad experience. The whole thing took over 2 hours and after all this, I can't record with the drone.
@gabadventures71274 жыл бұрын
Do you have to take the whole drone apart to replace one arm?
@KevinPinto3 жыл бұрын
@@gabadventures7127 Did you get an answer to this question?
@schlepers Жыл бұрын
Dont even bother wasting money on the kit. Just toss and buy a new drone. I tried this repair and some of the plastic connectors broke off. This is way too difficult to repair.
@flipboom3 жыл бұрын
Your video leaves out a lot of stuff, you don’t even explain how you take the ribbon and right front antenna that’s underneath the board off! You literally skipped that
@ericsson1O5 жыл бұрын
Autant le vendre un quitte
@RogelioRoyerGarcia5 жыл бұрын
so what can i do with the body? lol bad guide...
@urgno5 жыл бұрын
there is someone that cloned your video in his channel > bHdM6rDCot0 < 👎 i think is not fair ...
@fyahblass5 жыл бұрын
RAT!
@AARNEMAN5 жыл бұрын
Oh no. Even a lady with red nails can do it, but feels like it could be a little complex for me.
@LeopoldoManuelRamirezMena4 жыл бұрын
hahahah, Red nails, ... and glasses, she's not just a lady, she's a cool lady that flies drones :)
@Benferno4 жыл бұрын
You skipped whole steps, like disconnecting and removing the memory card holder, and disconnecting and removing the circuit board with the vertical camera. And the copolng fun does not just pop of with a flip of the thumb. In fact it seems designed to not come off at all. This machine is disoposable and should be marketed as such. Parrot is a horrible company with lousy products.
@user-Chikotillo4 жыл бұрын
You fucking kidding me? Parrot makes great products for good prices, professional photographers using Anafi to shoot videos for their work, I also use their products and never had issues, Bebop 2 was highly reparable, but Anafi is far more advanced, thats why its much harder to repair, but it doesn’t mean its crap or disposable, DJI drones also disposable but cost twice as much, just learn how to fly and you will never have issues...
@fabthefab754 жыл бұрын
@@user-Chikotillo Obviously some fanboy who hasn't tried to deal with the anafi mainboard yet.
@fabthefab754 жыл бұрын
@Benferno Totally agree with you
@redaimellah5 жыл бұрын
If I live in the third world country I will try to fix it, but I live in USA I have no time for this, I rather throw the drone in the garbage and buy an other one, very simple!
@Golf4org5 жыл бұрын
New drone: 600$+ New arm: 20$ + 30 Min
@cartechniques101icanfixtha24 жыл бұрын
I'll buy it
@AECRADIO14 жыл бұрын
Send it to me, I will take the time to repair it...easy.