Detailed walkthrough on how to install a gps and receiver into the betafpv pavo20, will be the same process for every gps and tbs crossfire receiver
Пікірлер: 33
@edgarvalles5 ай бұрын
I put 5 blade props on mine a week after I got it love how quiet it is
@Todd_G_FPV5 ай бұрын
Link? I love how this little thing flies on 3s with stock props!
@Phillyfpv5 ай бұрын
I tried the 5 blades props and it is really quiet but it has caused massive vibrations and a huge amount of prop wash! I’m actually trying to pid tune it but I’m having a hard time grasping the pid tuning in depth!!
@Phillyfpv4 ай бұрын
You can use any available uart on your flight controller! I think I used uart 4 on my pavo20, as long as you set it correctly in beta flight then it will work.
@muchamadramdany90714 ай бұрын
🎉
@Mmd8bn3 ай бұрын
About to try this myself when I get my GPS and ELRS receiver in the mail. It's a shame this vid is only 360p as it makes it very hard to see what's going on. Thanks for posting this though mate!
@Phillyfpv3 ай бұрын
I was very upset about that when I made this video I’m sorry about that, I used the Mac editing program to edit and it took me along time to figure out how to switch it to high def as it’s a fairly hidden option, My latest videos have been made on da Vinci resolve so this problem won’t happen again, don’t hesitate to ask me for help I will be more than happy to help , I can walk you through any problems you might come across.
@Mmd8bn2 ай бұрын
@@Phillyfpv Hey mate, I managed to get a GPS module soldered up to UART6 and it's all working fine. I'm keen to get an external ELRS receiver onto UART1 but I'm wondering did you disable the power for UART3 (the inbuilt ELRS receiver)? On their site it mentions you can cut the power to it by removing the chip bead but I'm not 100% sure what this means
@Phillyfpv2 ай бұрын
All I made sure is to not have that uart configured in betaflight, as long as the uart for the specific peripheral you want off is switched off in betaflight then it won’t be used if that makes sense!
@Phillyfpv2 ай бұрын
Hey mate how did you go? did you get your receiver wired up and disable the in built elrs?
@Mmd8bn2 ай бұрын
@@Phillyfpv Thanks for asking mate. I did exactly what you said and just enabled serial rx for the uart. I haven't flown yet but it looks like it's going to be much better than the inbuilt receiver. Thanks again mate.
@Phillyfpv5 ай бұрын
I take it you have the o3 air unit? You need to go into the presets tab and load the correct preset! When I get home I can help you properly, give me an hour or so and I can guide you to exactly what preset you need to load! Once that’s done you should be able to see your osd👍
@vadimus20075 ай бұрын
How to you like these props vs OEM two-blade ones?
@Phillyfpv5 ай бұрын
I like the extra power they provide and they look good as well but my props for some reason cause a lot of oscillations and prop wash, I have been studying Chris rosser’s video on pid tuning so once I get rid of that I will stick with the 5 bladed props for sure.
@lalojr76ify5 ай бұрын
This might seem kinda of foolish to ask, but what is the purpose of the gps on the pavo20? Will it help self level out like the DJI Avata and allow it to return home if it looses signal or something? The Avata and mini4 pro are the only drones I’ve used that had a gps on them. Nice video
@Phillyfpv5 ай бұрын
Not foolish to ask at all, I always put a gps on all my quads in the off chance I lose it, I have lost three drone completely and I would of gotten them back if I had gps rescue, unfortunately the gps systems on beta flight aren’t as advanced as the dji and that is because most of the time fpv drones don’t have a magnetometer or compass allowing them to do way point missions, but they do allow gps rescue and auto landing which is great for that added security in case of an emergency.
@muchamadramdany90714 ай бұрын
Mr, Gps n rx to uart ?
@Phillyfpv4 ай бұрын
You must put the gps TX wire to the flight controller RX pad, and the gps RX wire to the flight controller TX pad.
@muchamadramdany90714 ай бұрын
🎉🎉🎉
@Phillyfpv4 ай бұрын
How did you go? Did you get it working?
@user-jj3te5wu8s5 ай бұрын
hey dad
@Phillyfpv5 ай бұрын
Hey sweetie tell your friends about my channel👌
@Phillyfpv5 ай бұрын
To anyone who has any questions or need help on there builds please don’t hesitate to contact me👍
@Todd_G_FPV5 ай бұрын
Could use help with my osd for goggles v2 lol
@Todd_G_FPV5 ай бұрын
I'm seeing some stuff but last time I put everything I wanted it all went all over the screen
@Phillyfpv5 ай бұрын
Of course, have you typed in osd wtf on the presets! And upload that and then set it in your msp? If you want I can make a video on how to do it properly?
@Todd_G_FPV5 ай бұрын
@@Phillyfpv no I haven't, and that would be amazing!