Bravo 👍Vous travaillez ou .

Te felicito por el trabajo......el mejor motor diesel 👍😉

Good job!

Just done mine following this guide. Thank you so much. You've helped me save some money! It was a little bit scary when I removed the glow plugs and moved the crank shaft via the 18mm bolt on the cam pully. As it made a poping noise. This is obviously the piston compression. Was a bit tight on the little ratchet I had so I used a breaker bar. Side note, be careful of any plastic clips on the fuel / coolant lines on the front of the engine. One popped off and fell down. I'm preying this has gone into the oil drain. Nothing has happened as of yet. But you may want to fully remove them to prevent this happening to you. Also, the wiring loom connectors can also get a bit brittle. So take care with these too. Constant heating up and cooling down. I can confirm the methods in this video work and you don't need any special tools. 2x spanners to remove the old injector. Rock side to side and pull slightly upwards. And if you keep the new one nice and straight no need for any special tools. Thanks again for this video. Helped me out loads.

Very good and funny videos bring a great sense of entertainment!

Bravo misyeu

👍👍👍1000лайков,свечи накала выкрутил и компрессию уменьшил,BRAWO.

bravo majstore super

Pump / jet in 1.9 TDI 115 , 130 , 150 , 100 and 105 PS group VAG

I love deisel engines so much

dobra robota

Hola, buen trabajo 👍 Como has limpiado el asiento de la junta?

👍bravo

Wish you could do a separate video on injection timing this time talking and explain why remove glow plugs and how did you find out the correct position to tighten the injector rocker nut...

such a good video but you should slow it down when needs to be understanding the important parts (;(( anyway I've just done this on my Caddy a few hours ago! And honestly I like that you took some efforts and wrote the ( T.wrench nm )on the screen. Thanks BTW if you would lift up the car a bit and put on the highest gear you can easily rolling the wheel to get your position of the camshaft ....

thank you

Great upload nice & clear, was that number 3 injector that was removed or what order are they in, tks 👌🇮🇪

Salut! Dupa schimbarea si reglarea injectoarelor dupa aceasta metoda masina porneste usor, motorul merge " rotund"valorile pe tester sunt constante '-0,20-0-10" .dar problema e ca scoate foarte mult fum alb.Apa nu o consuma, uleiul pare in regula...ce poate fi? Multumesc anticipat! Cu stima!

Normalement on utilise un extracteur pour sortir l'injecteur-pompe. Les vis doivent être remplacées après chaque démontage car elles sont vissées à l'aide d'une clé dynamométrique puis on termine par un serrage angulaire. Une vis serrée au serrage angulaire s'allonge c'est pour cette raison qu'elle doit être changée après chaque démontage

Top Ferrero mirci

Thanks

Hello , I am getting a code in my skoda Laura 1.9 TDI PD is P1267 can you please tell me what can be the fault

When i pulled my injector, the piston filled with fuel so I've changed the oil but now its back together it won't start. Did you need to prime the injectors and if so how?

It‘s common for some people to use silicon sealent for the valve cover because they are made out of plastic they warp and won’t seal properly after some time. Sealing it with silicone isn’t the proper but cheap way

Can you give me a lecture on using filtered motor oil filtered through a 5 micron filter system? 2005 bew. I had a 1/2 bad injector before I put one tank through. Now the motor is shaking abit at a idle. Am i going to deck pump and stuff?

When you replace an injector , the new injector has to be programed or what to do?? , or I just put a new injector in and thats it ?

I migliori motori che non faranno più duravano troppo

One question, did you put the fifht gear and you rolled one wheel to move the camshaft so you can reach the top of the inyection and then you tighten to the max?

Did you sucked rest of fuel from the top of the piston when you pulled out the old injector?

hi man, thx for the video. Can you tell me the size of the hexagonal (Xzn) for the rockers bolts and the allen size for inyectors bolts? THANK so much

I'm having a trouble code P0302/00770 and I'm thinking on a issue on the injector number 2! I have change recently spark plugs but I'm not sure if there's anything to do with that I think if was that would appear different fault code! No glue needed when putting the new head gasket seal? Great video

O my word, is this how they work in a garage? No wonder I will nevet trust my car, or van in these places.its a wonder this guy has the right tools,and know how, let alone the skill. 😡

When you pulled the rocker cover off 🤔 hahaha who seals a rocker cover like that xD

Pushing the injectors in by hand isn't enough and the bolt will not pull them down. They need to be tapped down. The hold down bolts need to the torqued and angle tightened down properly. The nip he gave them here will lead the injectors rocking and eating the head. The injector rocker adjustment should be done with a dial gauge not best guess.

Только в третьем цилиндре Топливо уходило в картер? Я думаю если вы полезли туда, то надо было менять сальники сразу на всех инжекторах

Hola buen trabajo Me pregunto que distancia se deja entre el inyector y las paredes del bloque?

What tool did you use to get to the difficuly bolt at the back? I've heard a union joint but what size? That's 😊

Hello sir, i hqve a skoda laura of this engine when i start the engine , car engine shakes and start i have replaced the injectors also but problem not gone yet, pls guide me

Is it 100% necessary to remove the glow plugs as I’ve got a 105 BKC and 3 of the glow plugs were rounded and just keep spinning and I wanna swap the injectors but i don’t want to fuck about with drilling the glow plugs out ?

Agora pergunto eu vai ficar bem vedado sem ser a junta original e tambem nao vai ficar com o trabalhar a matraquear ao retirar o injetor afinado assim mais ou menos ? Quem poder responder fassa o fafor de responder

Обычные горе люди посмотрят и так же херого сделают. Хотя, думаю, это Миру и нужно! Как визуальное пособие что внутри, пойдёт:)

🎉

Suruburile alea de la rampa calaretilor, nu trebuiau puse noi? Nu trebuia folosita cheia dinamometrica, pentru strangere la cuplul dat de fabricant?

Where is the subttiles?

best engine in the world

Hi, I had just completed 2,51,000 kms from my 1.9 tdi PD deisel engine. I am facing issue in Starting when engine is hot. When it is cold it get start smoothly but when it gets hot, it starts getting trouble in starting. I had checked the starter motor and ECM both are working fine. No any faulty code when i scanned. Could you please help me with the solution. I will highly appreciate your response. Thanks

Did you remove flow plugs? I've just done this job but I didn't remove glow plugs. My car idles ok but has very low power.

I must have missed it. Did he take the cam out.

Esta bien pero a Cámara rápida y sin especificar el trabajo de 0A10::6

Salut am o problema cu un b5 motor de 1.9 pompe duze 115 cai. Am refacut chiulasa masini si surpriza masina acum nu mai porneste. Mentionez ca masina pornea sfert de cheie innainte de reparatie. Acum porneste doar trasa. Dar nu are putere deloc este foarte foarte lenta abia reusesc in treapta 2 sa o duc la 2000 turatii. Astazi am verificat eu personal injectoarele si am gasit un injector cu cod diferit si am sunat pe cineva si mia zis ca acel injector nu are nici o treaba cu masina mea. Nu nimere codul la injector cu ce am eu nevoie. Sa fie din cauza la acel injector

Eu trebuie sa schimb un injector la un passat b6 2.0 tdi,,trebuie sa il schimb pe cel defect sai trebuie toata 4 schimbate..?

Where does the fuel enter from since their are no fuel pipes leading to the Injector???

Dupa ce s a montat noua garnitura la capac...s au folosit suruburi noi?

Ai putea sa menționezi toate sculele pe care le-ai folosit? Gen T30

hi there is this the same for the bmn 170 models thanks

Salut, cum se numeste acea garnitura care ai pus-o la capac ? Si unde ai gasit-o? 1.9 tdi atd o zi buna!

Salut am si eu un MK5 1,9 tdi (BXE ) si am probleme cu un injector ,pe cilindrul 2 ,daca gasesc unul din dezmembrari sa fie acelasi tip de motor (bxe )potriveste injectorul sau trebuie sa fie accelasi part numar ca si al meu ori nu.i musai ?pot sa.l iau si sa.l pun direct asa cum ai facut tu in tutorial ?multumesc

My 1.9TDI BXE in passat B6 sometimes shakes on neutral, 1-2 seconds short shakes, especially when cooling liquid has proper temperature 90 C degrees. Power and overall engine work is fine. Do you think there can it be injectors seals? Regards from Poland

Ce motor e in imagine? difera fata de a4 b7 2007 2.0 tdi bpw. ? Ai avut DPF incarcat cu cenusa? L ai curatat sau schimbat? Multumesc pt sfat!

hi mate, ref code are same for all injectors or can be different ?

Ок.

What about 16valve engine?same 180 degrees?

Salut, la un 1.9 tdi cod motor BXE se reglează la 180 sau 225

On the AVF PD engine those rocker shaft bolts are stretch bolts and should not be reused. Also, if you are fitting a new injector, the adjusting screw should also be renewed. ps please buy a good make 1/4" torque wrench before you snap something .

Dacă schimb oring urile la injectoare, trebuie sa schimb și șuruburile de la axul de comanda al injectoarelor?

Pentru siruburile de la injectoree,cele stelate , ce marimi si ce chei se folosesc. Mersi.

Hi having hard start could it be leaking injector

do you set all four injectors

1:30 diesel mechanic guys they love silicone sealant...

Can an injector only make noise when hot?

Its same for 2.0 tdi too?

Salut! Imi poti explica si mie mai in detaliu reglajul injectoarelor dupa inlocuirea unuia?

What was the symptoms from the faulty injector , how to check the injectors are faulty ?

Hi friends I'work skoda Fabia 1.4 tdi engine the fault code is comming P1266 P1263 P1260 wat is fault please help

Same for a bew also?

Hello is this the same for a 1.9 TDI asz polo?

what tools did you use?

no new rocker bolts? :))

Do you have to code the injectors on the ECU after installing?

Hi. Why did you replace the PD injectors?

Salut, am schimbat si eu 2 injectoare la un audi a4 b6 1.9 AWX si acum trepideaza mașina, injectoarele nu sunt acelasi cod ca cele originale. Trebuie codate din tester ?😁

Siento poner este comentario... Error fatal se cambia los tornillos de inyectores según manual y los newton de apriete? Este vídeo puede no es lo más correcto de ejemplo

Zamena sibeera audi A8

sorry is this to replace injectors😂 next thing u tell me is that u have to take the engine out to replace the oil

Opel frontera

.

It won't be work properly.

Ахахаха, поржал с гермета

Y los grados al tornillo que agarra el inyector no se los das😂😂😂 igual que a los tornillos del soporte del balancín 😂😂😂😂

PD injector

Co za bezmózg tyle tego tam nawalił?

Everything is so simple in this video untill you start doing by yourself and figure out injector 0 sealing rings can stay inside despite you remove injector (buy some long 0 injector sealing ring hooks/picks just in case . Better have and dont need than dont have and need thank me latter)oh and that fucker injector/s siting other there so tide you spend good amount of time trying to get it out gently ( you dont want damage anything arent you?you love your car arent you?) And dont forget cover oil canals if some bolt. screwdriver bit or something ealse accedently fall other there you fucked. Thats just my personal experiense so far. Next time simply just pay mechanic to do the job. P.s. sorry for my bad english P.p.s good luck 😂

you didn't set valve clearance 😱