Make 3.7v to 100000v High voltage generator

Make 3.7v to 100000v High voltage generator | High voltage transformer

Рет қаралды 6,638,295

2 жыл бұрын

Make 3.7v to 100000v High voltage generator | high voltage transformer
in this video i have shown how to make a high voltage transformer. Here i have used a old flyback transformer's ferrite core. Anyone can try this at home.
How to Make High voltage transformer at Home.
In this video I show how to make a high voltage boost transformer and generate high voltage. You can use MOSFET z44 or tip122 or D880 to build this circuit.
high voltage generator(DIY high voltage transformer) using transformer and MOSFET z44 or transistor tip122 or D880 . This circuit is often used in shockers and igniters, so be careful.
------------------------------------------------
about this video :
electric generator
high voltage generator circuit
Plasma lighter using one mosfet
how to make high voltage generator at home
high voltage
flyback transformer
high voltage inverter generator
high voltage generator
-----------------------------------------------
data sheet:
drive.google.com/file/d/1tFK8...
------------------------------------------------
List of tools and parts:
drive.google.com/file/d/191f-...
------------------------------------------------
Together by Justhea / justhea
Creative Commons - Attribution-ShareAlike 3.0 Unported - CC BY-SA 3.0
Free Download / Stream: bit.ly/3oAR9Yu
Music promoted by Audio Library • Together - Justhea (No...
-----------------------------------------------
#highvoltage #stungun #generator #PenguinDIY #plasma #electricarc #arc #Penguin

Пікірлер: 982

@PenguinDIY 2 жыл бұрын

Thanks for watching 😉😉😉 Subscribe to my channel if you like❤️

@saifthepenguin651 2 жыл бұрын

you welcome

@BhartiPatil. 2 жыл бұрын

Bro can you sell that I cant do so much hard work on that i want to buy that damn thing

@dinoshorts1015 2 жыл бұрын

My also.

@blackbearelectronicswithco9541 2 жыл бұрын

This is cool, but it is impossible for the voltage to be 100,000 with the air gap being so small. 5kV sounds more reasonable

@gunner5183 2 жыл бұрын

i agree with you

@jacktherip7750 2 жыл бұрын

Actually less gap=more amplification

@BritishEngineer 2 жыл бұрын

@@jacktherip7750 This is not an amplifier.

@Deniz24-61 Жыл бұрын

average 10000 =1cm in room conditions

@multiarray2320 Жыл бұрын

@@Deniz24-61 no, 10000v for each cm (according to electroboom)

@jsmythib 10 ай бұрын

When I saw the clock transformer I was disappointed. Until I realized it was just a spool of wire :) An amazing DIY transformer project, ground up. Awesome post.

@propheteyebert7063 2 жыл бұрын

Good project. The transformer turn ratio is 150. With a tip122 transistor, the output is 15,000v max. The circuit should be tweaked to keep the primary voltage below 90. Otherwise, the transistor will eventually fail.

@adiprai2887 2 жыл бұрын

Helpful tip, particularly for a person like who doesn't have idea about configuration of the circuit!

@pktamilan1977 2 жыл бұрын

Is that kill human being

@wilsontkl 2 жыл бұрын

@@pktamilan1977 it can even vaporize a T-Rex

@K1ttyKn0wledge 2 жыл бұрын

@@wilsontkl are u dumb? no it cant. The voltage is high but the amperage is super low, u wouldnt even feel the current, it would just burn u like fire

@denisjakman654 2 жыл бұрын

mm I have been left with a doubt, do the amps increase with that transformer?, and it can work with AC electricity?

@user-jh8xv5rl5j 2 жыл бұрын

شكرا لك على هذا المجهود الطيب ارجو وضع قائمة بالمواد التي استخدمتها ان امكن ذلك تحياتي الخالصة لكم مؤيد كريم من العراق

@PenguinDIY 2 жыл бұрын

بالتأكيد سأضيف القائمة في قسم الوصف قريبًا.

@user-bm4ig2ve9o Жыл бұрын

Вообще ничего не понятно!

@sethreign8103 9 ай бұрын

Those are some gorgeous looking solder joints 🥰

@HUGEHARDTHICKANDVEINY 8 ай бұрын

4:03 made me search the comments for this lol

@OmeedNOuhadi 2 жыл бұрын

Thank you very much for sharing!

@GiorgioMotorsport 2 жыл бұрын

Bravo!!!👏👏 Joder ...tu eres un máquina con la electronica. Gracias por enseñarnos estas cosas.👍👍

@chusdiaz9160 4 ай бұрын

¡Bravo!!👋👋👋 No son 100000 voltios pero usted siga aplaudiendo 👋👋👋👋 🤭

@hugomazariegos7406 2 жыл бұрын

Muy buen proyecto, lo felicito, me encantó el Mini flyback.!!! 👍👍

@Elmuzaki 2 жыл бұрын

Wow this is amazing 🤩🤩🤩🤩🤩🤩🤩🤩🤩🤩

@joelbraganca7075 2 жыл бұрын

Este circuitinho e muito bom

@fiivin8550 Жыл бұрын

Wow, I can do it again, you are cool and good at doing it again🥰

@aportandolealplaneta8970 2 жыл бұрын

Realmente fasisnante gracias gran maestro por su infinita sabiduría bendiciones

@ramonsantana4258 2 жыл бұрын

Muito bom mesmo.parabens

@shahidashahida7184 Жыл бұрын

Jfjf kj jbc NC jjkglhkhg kj hj do j just ui do it I it k

@HungLe-dz1jy 2 жыл бұрын

Hay quá bạn làm giỏi quá cái đó tạo khí lyonâm hay lắm đấy 👍👍👍👍👍👍👍👍

@inoxsildet8568 2 жыл бұрын

wow muito bom!

@longvan2720 2 жыл бұрын

@呼嚕呼嚕sùc

@TABISURU2019 Жыл бұрын

I live in Japan and enjoy various DIY projects, but your idea is wonderful. I'd love to learn. Thanks to you, the range of crafts I can do has widened. I'm grateful.！！！

@empathicallyyours4937 Жыл бұрын

This is all a prank trick 😜

@eddyyu7091 2 жыл бұрын

Delicate and powerful, sir.

@bulentdemir6641 2 жыл бұрын

güzel bir video , çok teşekkürler.

@againstnationalismliarsand2615 7 ай бұрын

nicely presented ..short and clear..thanks 🍀👏👏

@user-kq9xw5fu1z Жыл бұрын

I would like you to draw a circuit diagram of the layout of the electronic components.

@suatkaleli5075 2 жыл бұрын

Hi; please advise the current consumption of the circuit?in case let's use 9 v battery and 7805 in the circuit so input v is 5 V.? However I have to say that it is impossible for me to wind 600 turns of 0.05 mm wire without breaking it off

@skysurferuk Жыл бұрын

If you need advising on that, you shouldn't be tinkering with this.

@andrewhoward7200 4 ай бұрын

Cool.

@suatkaleli5075 4 ай бұрын

@@skysurferuk if you able to perceive all the matter you also sould not be tinkering with this too

@JoseSouza-rk7dm 2 жыл бұрын

Muito bom Campina

@alexpawlov7607 2 жыл бұрын

Если смоделировать музыку высокой частотой и подать на этот преобразователь. Должен быть интересный эффект.

@gushund 2 жыл бұрын

Great job .... could use it in my camping trip for start fire

@sciencespectrum3855 2 жыл бұрын

Yes

@godgame9841 2 жыл бұрын

Could learn English lmao

@hotlemonade6643 2 жыл бұрын

Or just get a lighter lol

@ananchansawang9354 2 жыл бұрын

รจ

@NaN_000 2 ай бұрын

Same lol

@Kolin4556 11 ай бұрын

Use the D209L transistor, it is much more powerful and durable. The D880 lives in this circuit for 30 seconds, then breaks through it, and also heats up. D209L plows like a watchdog and does not heat up even without a radiator. And from it the spark is longer and more powerful. The D880 C-E has a voltage of 60V, the D209L has 700V, so it does not break through!

@herobrine1847 3 ай бұрын

What do you mean break through?

@vellingirisamya1154 4 ай бұрын

Very useful video. Clear demo. Keep it up

@leandroluque3903 2 жыл бұрын

guau interesante y haora que ya no hay dislaik no queda de otra que intentarlo y comentar me gusto nuevo suscriptor

@kevinm3751 2 жыл бұрын

What did you use to ensure there was 600 turns x 6? Dont know about anyone else but I am not keen on the idea of counting 3,600 revolutions of the drill...;)

@Lucas_sGarage 2 жыл бұрын

If u know the speed of the drill you take the time, for example if u need 6k turns and your drill goes up to 3000rpm u count 2 mins and you are done

@JatPhenshllem 8 ай бұрын

@@Lucas_sGarageNice

@user-qs9bc5fb9p 5 ай бұрын

Можно сосчитать только одну секцию, а остальные мотать примерно по объëму первой..

@cryzz0n 2 жыл бұрын

i used the same wall clock coil for my HV transformer for an experiment but when i tried using a irf840 mosfet to drive it, it melted some parts of the coils so im rewinding it with the wire from a mircowave turntable motor and also trying out a new winding strat (my transformer pot is also in sections but just deeper) the coil was 270 ohms before trying the irf840 i used a dual npn transistor switch and that worked better but only with 2-3kv arcs

@thang_handmade5916 Жыл бұрын

Nó thật hoàn hảo, chúc mừng bạn!

@DracoSauros Жыл бұрын

VERY GOOD JOB ! ITS LIKE PLASMA ENERGIE !!!!

@ocoolsanni2803 Жыл бұрын

Amazing project I love it, what's for your next video on the same? Is it possible to make it self healing on the battery, like it's recharged when it drains to a certain voltage ⚡ and then use the output to power your TV?

@tech.5137 Жыл бұрын

The high voltage coil can be buried by dripping wax from a candle while melting it, rather than using plastic tape to hold it in place, to prevent moisture from entering the coil and make it stronger and last longer. In fact, I bought this same high voltage generator circuit from Ariake. 15KV High Frequency DC High Voltage Arc Ignition Generator Inverter Boost Step-Up 18650 DIY Kit U Core Transformer Suite 3.7V

@TheHpthpthpt Жыл бұрын

Is there a website where we one can buy such high voltage circuit readymade? Please advice

@jakefriesenjake Жыл бұрын

Please advise where to buy

@siavashdarmani1190 Жыл бұрын

there are actually lighter made this way. I love those.

2 жыл бұрын

Nice work!

@engineerforfun392 2 жыл бұрын

Hey bro good job but i have a question can i replace irfz44n insted of that mosfest

@philipdrew10 Жыл бұрын

Impressive. Informative

@titsseeker9396 2 жыл бұрын

Wow it's so awesome! It's literally an arc lighter right? But how could you charge the battery of it?

@PenguinDIY 2 жыл бұрын

The 3.7V batteries can be charged with the charging module

@BhartiPatil. 2 жыл бұрын

@@PenguinDIY you should have connected TP4056 module to make the arc lighter rechargeable

@tgmelinda7544 Жыл бұрын

You should probabaly vacuum pot that transformer winding in resin to prevent cross coil arcing and to make sure all the gaps are filled.

@manreaper1238 8 ай бұрын

Will not help. The coils will not be saturated

@user-qw4bd5ib6j Жыл бұрын

Thank you for the brilliant idea! I've made what you say, but I have some problems. It doesn't make the electrical arch and can't fire up paper. I'm using tip122, 3x 1,2V rechargeable NI-MH batteries and my ferrite core is from an old TV transformer so it's maybe twice bigger than the shown in the VIDEO. The number of my turns is like shown. Where do you thing is the pormblem? Please give me advice how to fix that problem.

@darianrodriguez6895 Жыл бұрын

you have to use 3.7 volt battery

@NewRetroTrader Жыл бұрын

Thanks, nice video 👍👍👍👍

@Bianchi77 2 жыл бұрын

Cool info, thanks for sharing :)

@gwhiz1397 Жыл бұрын

The rule of thumb for spark gaps is 3KV (3,000V) per cm. (10mm or 0.393701 inches)

@Covid_19_23 Жыл бұрын

А я знаю правило 1 kV = 1mm

@SuperFreeEnergy 2 жыл бұрын

Very good 👍👍👍

@abhimanyudeshmukh2759 7 ай бұрын

Good project I appreciated it

@istvankiss5712 2 жыл бұрын

The breakdown voltage of the transistor is 60V. There will be much larger reverse needle pulses in the primer that will destroy the transistor in a maximum of half an hour. I did one many years ago and my 100V transistor also broke down.

@victorfranklin338 2 жыл бұрын

Right idea ! Very good

@krishnamandal9550 2 жыл бұрын

@@victorfranklin338 xg .👑

@cristianpopescu78 2 жыл бұрын

@@victorfranklin338 What about protection due condesator?

@AdamGtr86 2 жыл бұрын

What is the point of the transistor? It doesn't seem to be doing anything since you have a transformer at the end of the day with 2 leads coming out.

@istvankiss5712 2 жыл бұрын

@@AdamGtr86 On the primary side, two coils are connected in series. The higher the number of turns in the primary, the smaller it gives inductive, positive feedback to the transistor. This is an inductive feedback oscillator.

@Klimat_Rasim 2 жыл бұрын

Супер 👍

@ocvuive Жыл бұрын

you are fantastic. great!!!

@thierrymaggiorino3664 Жыл бұрын

Very Nice bobine 😎👍🏼, Good job 🛠️👍🏼...👏🏼👏🏼👏🏼... Thank you for the partage..

@Gomes-Jc 2 жыл бұрын

Nice. Try to put these cables in a dipole antena, each cable in one pole and turn on and verify the signal of one celular close to.

@Tutankhamun1333 2 жыл бұрын

Hey Penguin thanks for making a awesome little device but also a ear killer to me as i could hear the very high operating frequencies and they were making my ears hurt really bad.

@309electronics5 2 жыл бұрын

Its self oscillating you cant change the frequency of it but eith a zvs you can, also the zvs gives more power

@user-cu1fs1hx1l Жыл бұрын

10,000Voltage이상이면 상업성있습니다

@megaman786 10 ай бұрын

Maybe if you cry about it some more your future self will go back in time and prevent you from watching this video....

@JatPhenshllem 8 ай бұрын

Poor you

@shousukekomi6284 Жыл бұрын

Buenas noches profesor me podría explicar cómo es posible que pase a esa cantidad de voltios ?

@guilhermebragadovale1445 Жыл бұрын

¿Cuantos amperios? ¿Es esto seguro? ¡Muy buen tutorial! ¡Yo adoré!

@gandrinuchiha5951 Жыл бұрын

nose tu te parese seguro se supone que es peligroso si no se maneja bien

@lightbulbgonewild3205 2 жыл бұрын

Less than 20kv If it was 100kv then you would need A MUCH larger primary to secondary ratio and a higher input voltage

@seditt5146 Жыл бұрын

Shits less than 10kv... likely less than 5kv.

@seditt5146 Жыл бұрын

@G E T R E K T lol yeah.

@seditt5146 Жыл бұрын

@G E T R E K T lmfao, go look at my page and check out the physics engines I program. :D. Dunce! Is that where your name came from, you just float around online wrecking yourself by saying the first stupid thing that pops into that little noggin of yours. Not only do I program physical engines but have created Tesla coils, Lasers, Lifters and tons of other high voltage projects. What are your qualifications again? None? Oh ok, that explains why you don't seem to know what you're talking about. You don't even seem to know how to gauge voltage by air breakdown distance for God sake.

@seditt5146 Жыл бұрын

@G E T R E K T No, you wrecked yourself. Not only on this comment but the other one you even mentioned yourself those rule only applies for spherical electrodes yet can't seem to realize that would make it a lower voltage here as its breakout due to concentration on a point is far lower. Its almost like you have NO practical experience, shocker.

@seditt5146 Жыл бұрын

@G E T R E K T Bro... look at the Fing video... how wide do you think the tip of his thumb is? Mine is flatter and larger at around 8mm... this is like maybe 2/3 that being generous as it comes to such a sharp point. Even using you absolutely unscientific anecdotal measurements you come out to roughly 6kv or so as the arcs produced here are literally only a couple millimeters apart and he jumpers it using tweezers so what exactly are you trying to argue as you are literally arguing with yourself here. This all ignores the ionization properties of the frayed wire allowing lower voltage breakdown. His real arclength here is likely about a mm or two. How much do you really believe this arc is because even saying 10kv is so insanely generous its unreal. You really don't seem to understand the slightest bit about any of this but are just here to argue to look smart while you accomplish the opposite in every single post.

@VukaGhost 2 жыл бұрын

For transformers like this one in video (which you can easily disassemble and assemble again) I would suggest two transistor zvs driver instead this blocking oscillator

@user-wu1jc7zr4y Жыл бұрын

Will this give an electric shock?

@harry2928 2 жыл бұрын

Accuracy and truth are invaluable in rating the specs of something. Also how about a device that's slightly durable, such that someone might want to keep it. Do that and Voila!! magnifique. !

@ranjitfernando5241 2 жыл бұрын

Thank you very much. If the circuit diagram was given would have been more easy to understand .

@PenguinDIY 2 жыл бұрын

The circuit diagram link is included in the description

@Baschkarma 2 жыл бұрын

One question: can you tell me how do this device produce alternating current out of a battery???

@PenguinDIY 2 жыл бұрын

Through the magnetic field that the choke in the secondary winding generates electricity.

@ayushjain-zb8kz 2 жыл бұрын

इसबारकेलोगशामिलहोंगे

@rodo19724 2 жыл бұрын

where do you get the plastic container for 6 turn x600 ?

@JorgeLopez-rq4sp 2 жыл бұрын

uso un ladron de julios para crear un campo magnetico como el de la corriente alterna, para luego aprovecharlo en una bobina muy densa para elevar el voltaje ⚡ fue genial, podria usarse como un encendedor cool o para una solddadura micro talvez

@JadzCraftsInvention 2 жыл бұрын

This is awesome

@ernestomercadomaciasat4rer896 2 жыл бұрын

Excelente, ^^

@randyops5246 2 жыл бұрын

3:13 - I think you should use Thermal Paste (like processors) not silicone paste

@PenguinDIY 2 жыл бұрын

They are all silicone paste. Only quality and concentration They are different. For such projects, this model of silicone paste is suitable.

@matthwy1 2 жыл бұрын

Thank you, this looks awesome! I have some questions. There are 3 wire connections on the primary side of the transformer. It was unclear in the video where they all went to. It looked like the center tap went to the base and one wire went to the collector. Is that correct? And the other side of the primary is connected to +3.7V? Also, why did you use 24 and 28 gauge wire for the primary? Why not just use the same gauge for everything? Thanks!

@PenguinDIY 2 жыл бұрын

Thanks. For how to connect the wires, please refer to the schematic in the description, tap the link to download the schematic. According to calculations, this type of winding is the best switching mode for this type of transistor, which reduces the temperature of the transistor.

@luboskligl3708 Жыл бұрын

Zdravím Vás, a odpovídám. Dneska jsem sledoval to video. a bylo to takto.: Vodič 0,3 šel na odpor, vodič 0,3 a 0,5 byly vedeny na + přes vypínač a vodič 0,5 šel na prostřední kontakt u tranzistoru. Na pravý kontakt tranzistoru šlo - z baterie přímo. S pozdravem Jezevec

@Midnight9909 2 жыл бұрын

За работу 👍

@shoaibeverything Жыл бұрын

You Are All Video Is Greatest 😊

@adiprai2887 2 жыл бұрын

I have a doubt. Is the output an AC ? If so, would it be wise idea to use diodes to get DC.

@autopartsmonkey7992 11 ай бұрын

no and why?

@harms123 10 ай бұрын

@@autopartsmonkey7992 Agreed.

@harms123 10 ай бұрын

Yes, the output is AC, but rectifying it only makes it more dangerous, especially if there's no point to it?

@alevazquez9869 2 жыл бұрын

If this is literally 100000 volts, I could dominate the world with such a powerful weapon.

@blueshiftrobs 2 жыл бұрын

Yes but mili amps

@ayyubklm1924 2 жыл бұрын

It is dangerous. But technology to use for peaceful purpose. Do not hurt anyone.

@alevazquez9869 2 жыл бұрын

@@ayyubklm1924 If you want peace, there has to be war.

@arandomguy4388 2 жыл бұрын

Rubber glove: SHINEI!!!

@nadinedevivier5556 2 жыл бұрын

100k volts is very dangerous

@matheus_784 2 жыл бұрын

Tudo muito bem isolado 😂

@creative-z 2 жыл бұрын

Can you tell the number of turns, the number of Volts in the 2 coils?

@michag.3981 2 жыл бұрын

To urządzenie daje maksymalnie 10000V a nie 100 000V

@katrinamorris5061 5 ай бұрын

Don’t try this at home if you don’t want to set yourself at risk

@rp70vlog40 2 жыл бұрын

Nice vlog bro keep it up😉

@DCBpower 2 жыл бұрын

Watching is a universal language. 👍

@davidreynolds4684 2 жыл бұрын

Those tweezers looked like metal. I would thing that person might experience a bit of discomfort running 100000 volts through their fingers. Maybe they had those hanes hot socks and underwear on at the time.

@Alkimi 2 жыл бұрын

That's what's so cool about this. With a tiny little 3.7V battery, there's virtually no wattage in those 100,000 volts, it's just the 1 Amp stretched incredibly thin by all those coils. You could touch it all day and barely get a sunburn

@davidreynolds4684 2 жыл бұрын

@@Alkimi Good point. If you ever want to get somebodys attention, gut a disposable camera. Keep the flash in tact. Let the "monkey" see the shiny thing then lay it down. I used to do it when guys wouldnt stay out of my toolboxes at my shop. Several warnings later id do the national geographic thing. The box was taller than i am so id charge the capacitor with a 9volt and reach up and kay it in the top tray after shining it their way. Then leave. Mins later come back and find them sitting on their arse with a messed up look on their face. Ive rigged up remote controls flaslights and lighters as well. Some are 360 volts. Sorry Rusty! Hope your out of therapy by now.

@Alkimi 2 жыл бұрын

@@davidreynolds4684 ah yes I learned that lesson early in life. I used to take everything apart when I was little.

@davidreynolds4684 2 жыл бұрын

@@Alkimi i had an erector set that had motors pullies steel gerders nuts and bolts etc. Dunno if they are even a thing anymore but my room was automated. Lights, massive stereo system(dad was a musician his concert stage equipment was my stereo system when he wasnt using it 18s and 24" subs , amps etc) Batteries wore out one day. I knew there was power in the outlets and the battery needed power. The battery case had pig tails so if i stick the two wires in the two slots in the outlet ill have power to charge the alkaline non rechargeable batteries. When i got my senses back and bandaged my cauterized burns all over me and what was left of my fingers i learned how to r&r an electrical outlet reset the breaker removed the black soot and burns up the sky blue painted wall slapped fresh paint on it and did it all before mom got home. Odly i ended up as a building contractor and a commercial electrician for years.

@Alkimi 2 жыл бұрын

@@davidreynolds4684 haha! I have a similar story. My friend had the erector set, I was so jealous, they were so cool! I just had Legos, but my dad was a mechanic and I had all the spare parts you can imagine. I soldered wires directly to a light bulb after determining that my lamp had no electrical components inside it, so it should work if I just connect the outlet directly to the bulb, right? I remember a bright flash and then the bulb exploded. I don't think it even tripped the gfi, and I didn't get shocked (as far as I recall lol) But once when I was 7, I had my finger in between the two prongs while I was plugging something in, and I felt the shock through my entire body for a long time before I was able to pull my hand back. I was surprised at how I seemed to be just fine afterwards. Lately I've been pondering the many memories I have that may in fact be the memory of my death, and how impossible it is to know if/when I died and have since been experiencing something like Dante's Divine Comedy.

@ddawsonwilsondawg7967 2 жыл бұрын

Make a bunch and then tune them and then make some music and then watch your views and subs flyyyyyyyyyy!!!

@peterbyrne8758 2 жыл бұрын

Why is it always about views and subs😔

@ddawsonwilsondawg7967 2 жыл бұрын

@@peterbyrne8758 It's not, daddy! I'm just trynna motivate 'em! You know, like Leroy Smith!!!

@diotubgamer544 2 жыл бұрын

@@ddawsonwilsondawg7967 Who the hack call a person daddy ,bro you gay

@user-gi5on5ey4m Жыл бұрын

Зачет!Это ты ещё автотрансформатор не пробовал...Попробуй,сердечник от строчного трансформатора,кинескоп телевизизор,с зазором,намотай по всей окружности хороший провод,в изоляции,и через любой разрядник,ну,например,просто два толстых провода,подать высокое напряжение на 1,5-2 витка.И тогда понравится....У нас,в России,были в свое время кинопроекторы,с ксеноновыми дуговыми лампами,я даже поработать на них успел...Вот там для поджига ламп как раз и была такая схема.Я её дома собирал,пробовал.Дуга мощная...

@user-jg5fn4fi2n Жыл бұрын

Только очки защитные для сварщика перед этим одеть

@PDgaming-st5lw Жыл бұрын

Very nice project very usefull

@user-th7hw4mm7f 2 жыл бұрын

محتواك جميل جدا وبسيط وغير معقد

@CaptainGlasgow 3 ай бұрын

This looks very cool,is it producing a small plasma field, it look almost semi solid when you push the match in before it bursts into flames

@_HoangXinPanie Жыл бұрын

I love khoa học công nghệ ❤❤❤

@JKWazTv 2 жыл бұрын

Very nice video 💛 new friend and like you

@brittsonplays1250 2 жыл бұрын

I have made my own this project when I was 6years old and I made a 220volt bulb glow using weak battery

@zoemeow7677 Жыл бұрын

Do you think could do this with a diy battery would be neat to see how powerful could get

@quocthai5529 Жыл бұрын

Can i use this as an input for my tesla coil circuit? pls answer ty.

@texacomann 2 жыл бұрын

This is a nice stun gun🙉💥

@user-ug5hp7ek8o Ай бұрын

điện nhỏ chíu như thế này chơi mói an toàn nè nếu có bị trúng thì chỉ bị giật tê thôi😂🤣

@vancemacd6315 11 ай бұрын

So crazy. I feel like this has simple way of exponentially raising the volts I wonder what would happen to sound passed through this device and hooked to a speaker.

@sergioesteban4665 2 жыл бұрын

Interesante fuente, pero no veo que sean cienmil voltios, seria poner diez de esos en serie

@user-yj1oq3uy8x 5 ай бұрын

Cooool,& so easy bro!!!

@KANCA_WESI 2 жыл бұрын

Wao 👍👍

@shlomoattia7706 7 ай бұрын

very good, Thank you ✅

@user-cu1fs1hx1l Жыл бұрын

계속발전시켜봐요 가능합니다 원거리에서도... 매우위험하니 조심또심하며 앞으로 해저케이불 필요없어요 송전기(전기보내는 송전탑도) 불필요하구요 특히 고압송전은 엄청위훰을않고있습 니다 지금까지 전자만가능했는데.. 이젠 전기도희망이보입니다 화이팅 계속 응원할게요~♡♡♡

@ikhffolo63 2 жыл бұрын

جهد عالي اوتوتر عالي شكرا

@edvincandradiyanto2672 2 жыл бұрын

Cocok ni buat korek elektrik

@diyathomevn Жыл бұрын

you are very good, i want to make a gill to catch fish

@cristianpopescu78 2 жыл бұрын

Wow!I didnt know that! Can it be used for engines spark plugs?

@PenguinDIY 2 жыл бұрын

To do this, a number of capacitors must be placed at the output of this module to act as a motor igniter. Exactly like a shocker

@CMAenergy Жыл бұрын

a simple way to make a taser, can be put on the end of long stick or cane to fend off predators or attackers good idea thanks

@theodorp6305 3 ай бұрын

Hey man! I just bought your thing, it arrived yesterday though, broken..:( I'm super sad cause it came from China and I am in Austria. Any way good job and have a good life :)