Penn Squall II 15SD saltwater fishing reel with frozen free spool release how to service and repair

Рет қаралды 4,271

3 жыл бұрын

This reel was a surprise to me as it is only a few months old. The owner uses it on Jet Ski fishing trips. The free spool release lever would not operate properly due to a frozen pinion gear on the spool shaft. See how to take this reel apart and repair the issue along with a general service.
I have been servicing #fishing #reels for over 20 years and am sharing my experiences here. If you enjoy the video, please like it and subscribe to see more on fishing #reel repair and service
Questions? Comments? I reply to all.
Thank you for watching - Dennis
email 2ndchancetackle@gmail.com
www.2ndchancetackle.com
Like us on Facebook at Facebook.com/2ndchancetackle

Пікірлер: 43

@stevecarrero4120 3 жыл бұрын

Nice to see that there’s still actual mechanics out there. 👍

@2ndChanceTackle 3 жыл бұрын

Thanks you Steve, and thanks for watching - Dennis

@moshesmoving Жыл бұрын

Similar to the old GS series. Bought a size 12 Squall casting special and have two 535 GS that I’ve been maintaining in good condition for years. Had a frozen pinion gear on a 345 GTI and crunched it with pliers even though I wrapped it in steel wool to protect the teeth. Fortunately Mystic Reel Parts still has spares for some of the older reels and because Penn uses common components across many models old and new I like Penn reels. They may not be buttery smooth like Shimano but they are tough fishing tools with lower up front cost of purchase and lower total lifecycle cost as well.

@lsmith1966 3 жыл бұрын

Once again an Awesome video! I'm always amazed at how easy you make it look and the way you heated the gear up and it worked out so well! GREAT JOB!

@2ndChanceTackle 3 жыл бұрын

Glad you liked it! This one was a challenge - And the reel is only a few months old! Thanks for watching - Dennis

@davidmcilveen5013 3 жыл бұрын

Great job Dennis..... although that blowtorch still makes me nervous!! 😂 Keep up the great work and stay safe. 🎣

@2ndChanceTackle 3 жыл бұрын

Me too, but I've used it a few times and have a little experience there. Hopefully I don't burn the shop down! Dennis

@davidmcilveen5013 3 жыл бұрын

@@2ndChanceTackle 😂

@brandonmcqueen1856 3 жыл бұрын

Dennis, Ithink you may have made one harder for yourself - the Fathom II and Squall II reels have fast access (right) side plates in that the RH plate is assembled with the main gear and drag as a unit. Pinion stays on the spool shaft. You only need to remve the 4 outside screws to get to the internals.

@2ndChanceTackle 3 жыл бұрын

Thanks for the tip. I will check to see how that works on the next one in. Best wishes - Dennis

@cedricjohnson459 5 ай бұрын

Helped me tremendously

@2ndChanceTackle 5 ай бұрын

Glad to have helped - Thanks for the note and for watching - Dennis

@christopherjenkins2373 3 жыл бұрын

Looks like a cute little Chinese Penn. I’m looking forward to a few more spinning reels but I’m in no way complaining! I have those Craftsan ignition wrenches. I use them especially on the big Luxor reels. If that spool shaft was stainless would it have rusted like that? Freeing that pinion was impressive. With my limited vision there is no way I’ll ever use a torch. I have a very small precise torch I sometimes use but I can handle that ne. I use it to heat circle hooks and coat them with powder paint. Then I bake the hooks in the oven. My wife doesn’t like that very much! I use a bottle I bought that has a two inch ti on it. I fill it u with Penn oi and that’s what I use. I think this was a very impressive repair and service. You proved again your experience and skill! What a great job.

@2ndChanceTackle 3 жыл бұрын

Chris - go and get a toaster oven from WalMart. They are cheap and it keeps the wife happy! I use one when I do the powder coating of Jigs - Dennis

@renemiramontes.loscabosgui5399 3 жыл бұрын

Awsome Dennis! The video I was really expecting. Have a great day ahead. Greetings from Cabo. ✌🏽

@2ndChanceTackle 3 жыл бұрын

Greetings and thanks for the note. Best wishes - Dennis

@joshuafigueroa6 Ай бұрын

Very similar to my fathom casting special.

@2ndChanceTackle Ай бұрын

Yes - the only difference between the Fathom and Squall is the case. The Fathom reel has a metal case and the Squall has a graphite case. Everything else is nearly identical - Dennis

@joshuafigueroa6 Ай бұрын

@@2ndChanceTackle nice

@svtenacity 3 ай бұрын

Dennis, do you have any videos showing the parts and servicing of the reel tension knob? I'd like to understand how it functions. Thanks!

@2ndChanceTackle 3 ай бұрын

I do not. The tension know butts to the spool shaft end. When you tighten it that puts more pressure on the shaft and slows the spool. When you back it off, it reduces the tension and allows the spool to turn more freely - Dennis

@craigd1275 Жыл бұрын

Why do a lot of people bring in PENN reels for repair? Is it because more people own PENN reels, or is it because they are bad? I just purchased a PENN Squall II. I contemplated buying a new PENN reel for a long time because they are made in China (like 95%+ of reels today). I have an old 30+ year old PENN that was made in USA. It is a great reel as is most of PENNs older USA made reels. .

@2ndChanceTackle Жыл бұрын

Penn is one of the BIG three which includes Daiwa and Shimano. They have sold millions of reels and all of them need service. Your choices are limited for quality saltwater gear and that is why you see more of these in for service. You should enjoy the Penn Squall and it should last a lifetime assuming you keep it maintained - Dennis

@MOONUNIT37 3 жыл бұрын

Awesome video..,I’m a beginner so I was wonder about the dog and the spring for the anti-reverse it didn’t seem to have one am I correct ?

@2ndChanceTackle 3 жыл бұрын

Corect Ray. This reel uses the Anti-reverse roller bearing clutch instead of a dog and spring - Thanks for the note - Dennis

@burberryducks6481 3 ай бұрын

Can you do a video on a squall 2 30

@2ndChanceTackle 3 ай бұрын

Use this one kzfaq.info/get/bejne/qq2RopSBr6jGnok.html It is on the fathom, but the only difference between the Fathom and the squall is that the Fathom has a metal case and the Squall does not - Mechanically, they are basically the same - Dennis

@SaltDonky 7 ай бұрын

Dennis, where can one obtain one of those wrenches you use, to remove the penn handles?

@2ndChanceTackle 7 ай бұрын

The wrench is by Alan Tan and is available through Mysticparts.com. You can follow this link to order one www.mysticparts.com/PennParts/Custom/168-TANI.aspx Dennis

@wesleylangell1659 2 жыл бұрын

Hey. Have you worked on any penn squall 2 with levelwinds? if so what do you think about them

@2ndChanceTackle 2 жыл бұрын

I have worked on them. They are a nice reel at a competitive price. Thanks for asking - Dennis

@moshesmoving Жыл бұрын

They are worthy successors to the GTI level wind series (which were US made reels). They’ve been good for me while salmon trolling and bottom bouncing for halibut in the San Francisco area.

@gonzafpv2843 Жыл бұрын

Hello sr, i have re assembled using the schematic, but now mi Star drag is like to tight, it's dificult yo move the star. Sorry for mi English and thanks for your time

@2ndChanceTackle Жыл бұрын

OK - You need to remove the handle screw. It is likely that you tightened down the handle before tightening the star adjuster. Take the handle off, turn the star adjuster down and then reinstall the handle. That should fix the issue. If you cannot tighten the star adjuster with the handle removed, then you need to check how you installed the drag stack - Dennis

@gonzafpv2843 Жыл бұрын

@@2ndChanceTackleMi procedure was: 1 adjust the star till one point that i need to put mi handle yo keep adjusting. 2 then i put the others two shims of the handle put handle and screw it. But the problem is that the star is pretty hard to move and it seems that its "shorter" than before , it has les clicks. I can adjust the star without the handle at some point, then i need to put the handle to keep adjusting the star...i Saw schematics and all seens to be fine. Thanks for your time dennys

@2ndChanceTackle Жыл бұрын

Hmmm - you may have the star adjuster cross threading. Remove the star adjuster and take the spacer sleeve off and then try to install the star adjuster. If it is not going on easily, then the threads may be damaged. If it is going on easily, then you need to recheck the drag stack. It is possible that the earned washer is not set in the grooves inside the main gear

@gonzafpv2843 Жыл бұрын

@@2ndChanceTackle i Will check that, thanks.

@gonzafpv2843 Жыл бұрын

@@2ndChanceTackle when You said "turn the star adjuster down" You mean clockwise? Thanks dennis

@burberryducks6481 3 ай бұрын

My drag is tight and has little movement now that i did this….

@2ndChanceTackle 3 ай бұрын

Hmmm - You need to recheck the drag stack and how you reassembled the reel

@burberryducks6481 3 ай бұрын

👍

@burberryducks6481 3 ай бұрын

My reel is so messed up there is no help online