How to perform a duct traverse using a TSI VelociCalc.
Пікірлер: 19
@daved34942 жыл бұрын
That was very interesting. I've only every used the pitot tube (many years ago) and, in reality it's almost impossible the ensure that the probe is pointing directly into the air-stream. I can understand why the 'hot wire' device is better. Thank you for comparing these.
@dossube6 жыл бұрын
Great Knowledge shared; Thank you, sir!
@brandonrandall38615 жыл бұрын
Very useful features. Thanks.
@chugg1593 жыл бұрын
Air Balancers are chad
@TanweerAhmed4 жыл бұрын
Good and informative
@joehiggins783011 жыл бұрын
This can be used for HVCA and LEV. The number of measurements is based on duct size. See a commissioning guide.
@mmmmmray2 жыл бұрын
Can you please give instructions on how to set up the Velocicalc software before capturing measurements on a 90-120 CFM Biological Safety Cabinet?
@TSIIncShoreview12 жыл бұрын
It is recommended that you be at least 7 duct diameters downstream and at least 3 duct diameters upstream of any obstructions or turns. These are universally accepted methods for determining where a duct traverse should occur to provide the best chance for a laminar flow. Please refer to the Alnor HVAC Handbook, Appendix A, for more detailed information on a Duct traverse procedure. Thank you.
@cbacca8510 жыл бұрын
Have you ever thought of adding levels to the probe? Maybe on the handle? Sometimes it is very hard to get into position where you can visually verify you are holding the probe level. This would help eliminate some human error.
@bokcelso668 жыл бұрын
if I'm having a duct which is 1 metre by 0.8 metre, how do I know how much holes and reading points I'm going to perform?
@GreenHouseAirConditioningLLC7 жыл бұрын
nice
@abdelhamidspeed90316 жыл бұрын
I am looking for work in ducts combinations ( installation ducts ventilation.. .. .)
@sakdasaosa97463 жыл бұрын
I need method for duct balance .
@AdrianMoscoso12 жыл бұрын
Hi, can you confirm this is HVAC system and not a LEV? 3:46: will 5 second measurement per point is enough? Do we need 3 diameter distance from the branch?
@TSIIncShoreview12 жыл бұрын
The procedures in this video are in regard to HVAC Duct Traverses, though other Duct Traverse applications may also benefit from this procedure as well. 5 and 10 seconds are very common sample times, but which is appropriate depends on your environment. For example, if you are sampling from a flow with a greater amount of turbulence, then a longer sample time may be needed.
@mhworld38985 жыл бұрын
Sir please make video PDS
@legend14535 жыл бұрын
Maldives Hulhumale island hospital and support building ventilation installation kzfaq.info/get/bejne/aNtpjM5etJ_Mnn0.html #hvac #duct #Havalandırmataşeronu #izolasyon #mekanik #havalandırma #yurtdışıhvac #Mep #mechanical #havalandırmasistemleri #hvacsystem #havalandırmafanı #havalandırmasistemleri #havalandırmaborusu #havalandırmamenfezi #havalandırmamotoru#havalandırmakanalı #havalandırmacı #havalandırmatesisatı #hvacsistemleri #news #turkey