Your Inty is loaded. Just a suggestion, apply all the cleaners (sprays) before washing and apply lube, polish, wax after 👍🏼
@gadgetwheelz7 ай бұрын
Thanks and Appreciate your suggestions 👍
@kevinvarghesephilip6 ай бұрын
That interceptor is smiling because its being taken care nicely!
@nishantsherawat2 ай бұрын
A job well done and fantastic maintenance. Need your help for the following - 1> I have read some place that WD40 is not good for rubber parts like the one inside the fuel cap. Isn't it better to use silicone polish for rubber parts/Indicator stalks/Speedometer. 2> Please let me know how to avoid getting rust on chrome exhaust in the long run. 3> How to clean the front shockers[the exposed steel part before the shocker sleeve] . 4>Which type of pressurized grease to be used for wheel bearings, especially during Monsoons. 5>How to clean the Water drainage near the Fuel inlet without inserting a wire into it. 6>How to maintain the battery terminals.
@gadgetwheelz2 ай бұрын
I am using WD 40 only for lock sets not for rubber parts. But if it comes in contact with rubber parts, I dont think it will damage in a large extent.I am using it for more than 4 years on my Interceptor. Rusting on bend pipe is a major issue.You cant avoid permanently unless you replace it with stainless bend pipes. Fork pipe cleaning i am not using any special cleaning agents.Just car washing shampoo. Greasing the bearings are done at local mechanic. I use nylon thick wire to clean the Fuel tank water drainage pipe Battery terminal usually cleaned by my local mechanic
@Zuputmer6 ай бұрын
Hey bro, I've got an Interceptor too and I've done almost all the same mods you have 😁 Great video, keep it up!
@gadgetwheelz6 ай бұрын
Thanks bro 😊
@Zuputmer6 ай бұрын
@@gadgetwheelzIf you don't mind me asking, what is that white colour powder that you had used during engine polishing? Never seen it before, please let me know what it is for
@gadgetwheelz6 ай бұрын
@Zuputmer , white buffing powder ,generally used at RE for buffing engine casing. I dont know the exact name of that.I got it from RE service centre upon request.
@Zuputmer6 ай бұрын
@@gadgetwheelz ah i just did a little bit of research and I think it might be aluminium oxide powder. Commonly used to polish metals, gives a mirror like finish! Will try it out
@MeAndMyRoyalEnfield5 ай бұрын
Well since it only takes 6 minutes think I'll clean mine tomorrow 🤣 Great video! 🥓🏍🏕
@deepakvailappilly8377 ай бұрын
Thank you friend for uploading and efforts 👍🙏🏻
@facundolazo93906 ай бұрын
Beautiful👌75.000km!! Any big issue you wanna share if you dont mind
@gadgetwheelz6 ай бұрын
No major issues, most of the cases it's wear and tear.No issues with engine so far.
@OfficialEupHo5 ай бұрын
Any link to the oil tank thing beside the oil tank cap
@gadgetwheelz4 ай бұрын
I bought the tank cap collar from www.way2speed.com
@dilipkimi7 ай бұрын
Can you do a video or give details regarding the alloys switch and the performance
@gadgetwheelz7 ай бұрын
Sure 👍
@dheerajdalal30264 ай бұрын
Which company's cone set bearings are you using for the bike?
@gadgetwheelz4 ай бұрын
NTN Tapered roller bearings
@gurucharanchundi3 ай бұрын
Hey man! Looking to get the Shine X pro foam sprayer! Seeing many negative reviews online, what has been your experience? Worth it? Is the quality good? Or should I go for the IK foam sprayer?
@gurucharanchundi3 ай бұрын
There's also the Wavex foam 3 sprayer now, confused between the three.
@gadgetwheelz3 ай бұрын
Dont buy Shine X Pro. Though the quality is good, spray is not effective after few usage. Try something else.
@gurucharanchundi3 ай бұрын
@@gadgetwheelz Thank you! I have seen positive reviews of the IK foam sprayer but it's a little expensive at 3.5k now. I think I will get that! As they say "Buy it nice or buy it twice". Thanks for your input
@gurucharanchundi2 ай бұрын
@@gadgetwheelz Hi, I'm considering getting the Baja Squadron Sport lights for my Speed 400. You have the Pro lights right? How has the experience been with them?
@gadgetwheelz2 ай бұрын
@gurucharanchundi , I am using Baja Squadron Pro, there are very powerful.
@thenilgirisbeyond436 ай бұрын
Hi brother, it's really nice to see an inty with 75k on the odo. Where did you get the visor? Any link?
@gadgetwheelz6 ай бұрын
That is a Puig visor, you can get it from Bikenbikers
@thenilgirisbeyond436 ай бұрын
@@gadgetwheelz thanks brother
@itz_chandru27307 ай бұрын
Purchase Link for the the drill buffing pad and set
@gadgetwheelz7 ай бұрын
amzn.to/48LxgSk amzn.to/3SdcdD2 Purchase links of all products in the discription .
@pervysensei28905 ай бұрын
How do tou prevent water getting in the tank
@gadgetwheelz5 ай бұрын
I haven't faced that issue. If fuel tank cap gasket is in good condition then no need to worry IMO.
@ANIL-ul1qb6 ай бұрын
❤❤❤❤❤🥰
@kennethheldreich66047 ай бұрын
Just a quick question, what tyres are you using 👍🏍🙂
@gadgetwheelz7 ай бұрын
Vredestein tyres
@muttineni036 ай бұрын
Where can I get S&S exhaust with header pipes?
@gadgetwheelz6 ай бұрын
you can get S&S exhaust from www.highnoteperformance.com
@CineScope0077 ай бұрын
Just curious...hows the mileage?
@gadgetwheelz7 ай бұрын
In city 25-26 kmpl, highway touring 30-32kmpl
@alfana76916 ай бұрын
Hi Which engine oil is good for the int 650
@gadgetwheelz6 ай бұрын
I use RE Liquid Gun during servicing at RE Service center. Motul 10w50 if I change at local garage.Never tried any other engine oil. Important factor is you should change engine oil on every 5-6k kms intervals.
@alfana76916 ай бұрын
@@gadgetwheelz thank you 👍
@abhirupsingh40045 ай бұрын
From where did you get the alloys for the bike man ?
@gadgetwheelz5 ай бұрын
Those are from RE , you can get it from RE Service centre or RE genuine spare parts sellers. These alloys for Interceptor and GT, so no need any modifications, it is a direct fit
@abhirupsingh40045 ай бұрын
@@gadgetwheelz but the guys at RE said that we cannot sell alloys for the older interceptor model as it did not come with alloys . I found this justification very silly . Then they said you should go for aftermarket alloys.hiw strange is that ?
@gadgetwheelz5 ай бұрын
That's very silly...try at some other RE service center,otherwise better try at RE genuine spare parts shop.
@kakarotthetamilgamer65297 ай бұрын
hi how do you got S&S Exhaust
@kakarotthetamilgamer65297 ай бұрын
i mean where
@gadgetwheelz7 ай бұрын
I bought it long back in June 2020 www.highnoteperformance.com/products/s-s-re-tapered-cone-slip-on-mufflers
@Ian-xt1mb6 ай бұрын
It's like polishing a pig. Pay a little more and buy a Honda.
@gadgetwheelz6 ай бұрын
😄😄 , thanks ....!!! I am happy with what it is.....just the miles talks.....
@ronaldpell28025 ай бұрын
Why would you change it ? Buy a Honda and be like everyone else with a plastic bike.
@antonbabych34817 ай бұрын
Hi! Nice video! As I see you have not stock alloy wheels size 17. Hiw it influences on speed??
@gadgetwheelz7 ай бұрын
Thanks...They are stock alloys (Size:18)made for Interceptor/GT 650 by RE. No difference in riding compare to stock spokes wheels