Can I Install This Power Bank Battery Into An iPhone?? 10,000 mAh
Рет қаралды 774,315
Жыл бұрынiPhone batteries are small, naturally because they're made to be as compact as possible. But not everyone needs their phone to be so compact. Some people, myself included, would prefer better battery life. In this video we're going to see if we can install a 10,000 mAh battery into this iPhone. That would drastically improve the native 2900 mAh battery and allow me to use this phone for days at a time. Let's see if we can pull this of...
Thank you for watching!
Buy My BLUE Mat :a.co/d/h3iPG3i
Website( Mail-ins & Contact) : www.phonerepairguru.com/
Second Channel: / @prgrepairtutorials2526
Ask a Question (Join the Subreddit): / phonerepairt. .
PROMO INQUIRIES: sean@prettygoodagents.com
Social:
Check us out on Instagram / phone.repairguru
Or on TikTok www.tiktok.com/@phonerepairgu...
Twitter: therealprg?lang=en
Facebook: / phonerepairguruu
My Repair Tools:
MAGSAFE MAGNETS : geni.us/BgyY
Tools and Organizer( iPhone Screen Stand/ iPad Screen Stand - Microsoldering tools etc) www.wrepair.com (Discount Code PRG5 for 5% Off Entire Store/ Discount Code PRG10 for 10% off $500+ orders)
Qianli Screw Driver Holder: geni.us/QIANLIICUBE
Qianli Screw Drivers : geni.us/QIANLISCREWDRIVER
Display / Battery Programmer: geni.us/jCfJoB
Tools Used (IFIXIT) : geni.us/JBYJF
Qianli Clamps: geni.us/QianliClamps
My Blue Mat: a.co/d/h3iPG3i
Ifixit Starter Kit: geni.us/STARTERKIT
Heat Gun: geni.us/HEATGUN
Electronic Screw DriverP: geni.us/WOWSTICK
Filming Gear:
LUMIX G85 geni.us/G85CAMERA
Lumix GH5 geni.us/PANASONICLUMIXGH5
Rode Wireless Go Mic geni.us/RHODEWIRELESSGO
Rode VideoMicro geni.us/RHODEMIC
Studio Lights geni.us/STUDIOLIGHTS
Spinning Thing geni.us/ROTATINGDISPLAYSTAND
Guru Approved:
Easy Button geni.us/EASYBUTTON
Gameboy Case geni.us/GAMEBOYCASE
MagSafe Cooler geni.us/jCfJoB
Nutella AirPod Case geni.us/PhUZC
Giant AirPod geni.us/GIANTAIRPOD
Nano Leaf Lights geni.us/xuKg
Anker MagSafe Charging Stand geni.us/ANKER
Framed / Disassembled iPhones Display xreart.com/?ref=l0076ztwht
Phone Repair Guru assumes no liability for any damage caused to your phone as a result of any of the information contained in this video.
Do not attempt unless you are open to the possibility of further damaging your device.
@PhoneRepairGuru Жыл бұрын
Power banks are lying to you video : kzfaq.info/get/bejne/rrhdeMyruZ2lnWQ.html&ab_channel=PhoneRepairGuru Last gold housing mod : kzfaq.info/get/bejne/fqearalkqaiaoYU.html&ab_channel=PhoneRepairGuru My BLUE Mat :a.co/d/h3iPG3i
@Canakeanything Жыл бұрын
Early
@kazifarhanafarhana8560 Жыл бұрын
Hello
@IPlayzGamesRBLX Жыл бұрын
Hi
@iamabouttohitthisclip Жыл бұрын
hi
@foxyrollsvr72 Жыл бұрын
Hi
@edwinawariyah6239 Жыл бұрын
The reason it did not work the first time was that the 2 LiPo batteries together in series gives roughly 7.4 volts which is way above what the iPhone 7 needs which is 3.7. The abnormality is what could have caused the boot loop since it didn’t know what to do with all the power at once. In fact you’re lucky you didn’t fry anything
@hristomirchev4026 Жыл бұрын
These batteries must be in parallel and not in series. I'm not sure if the phone can handle more than 6 volts on the battery traces. Most smaller chips are limited at 5.5 volts at the absolute maximum ratings
@navigatorofnone Жыл бұрын
@@hristomirchev4026 good point.
@thisfeatureisbad Жыл бұрын
@@hristomirchev4026 I'm surprised that the BMS survived that voltage without actually starting to discharge the batteries.
@alternatecheems8145 Жыл бұрын
@@hristomirchev4026 also the actual voltages used are as small as 0.6v
@E-hab Жыл бұрын
That's what I wanted to say
@Dan-oj4iq Жыл бұрын
Don't think the people at Apple would like this and I'm not even sure why they wouldn't. I just know they would not approve in the least. If you took this step any further they would get their people to cripple this workaround with a firmware update. Guaranteed.
@navigatorofnone Жыл бұрын
who cares what apple thinks, they didn't give a shit to their customers since forever.
@joshuamarshall3146 Жыл бұрын
its using a real bms board i dont think they can patch it out i dont think apple will care they dont care about hackintoshes and thats a way larger number of people than who would ever do this
@joshuamarshall3146 Жыл бұрын
@NoisyGamer ur mum wears socks to bed don’t tell me to mind my own buisness
@Anaahu_69 Жыл бұрын
They wouldnt approve cuz they want u to waste ur money and buy a mew phone but just with a different design
@prabhsaini1 Жыл бұрын
yeah because they would release a new update just because one guy soldered a battery which has to much voltage to his iphone.
@ceticx Жыл бұрын
Now I really wanna try making a giant battery, a 3d printed thick af iphone housing, and some really long screen ribbon cables and make the thickest iphone ever
@All-sk9qz Жыл бұрын
Make it durable like the 3GS
@dirrology Жыл бұрын
Yeee def do a 3d printed case for it
@ceticx Жыл бұрын
@@dirrology I don't have a 3d printer but I think thats a minor issue I got this
@Windo0ows Жыл бұрын
@@ceticx pcbway has 3d printing services and they offer materials that aren’t plastic
@marco56702 Жыл бұрын
I would buy it!
@syedfaizalishah6928 Жыл бұрын
We want a battery drain test once you get the phone assembled the way you want !! 😄
@RestoreTechnique Жыл бұрын
Genius! Thanks for pushing the boundaries for our entertainment 😀
@PhoneRepairGuru Жыл бұрын
🙏
@jackforlife101 Жыл бұрын
Yoooo i love ur channel
@RestoreTechnique Жыл бұрын
@@jackforlife101 😀💚
@pizzabudies826 Жыл бұрын
@@jackforlife101 😮😮
@pizzabudies826 Жыл бұрын
@@PhoneRepairGuru I love your channel you are so cool
@Sirmellowman Жыл бұрын
This video quality is perfectly good bro, keep up the great content!!!
@PlanetTokki Жыл бұрын
Don’t worry, we love your videos no matter what. This, this kept me watching for the full six minutes. I didn’t even think of leaving lol
@haidar2638 Жыл бұрын
I skipped because too much talking
@RikAindow Жыл бұрын
It's great to see you making longer videos again. Welcome back!
@sir.alexei Жыл бұрын
Really miss long videos and I’m glad that you feels better now 🙌🏻
@Perry24680 Жыл бұрын
I’m happy to see a vid from you. I’m excited to see this go further. As always, good work. ♥️
@TeamAI. Жыл бұрын
how long does it take for your longest repair ever
@Midblur09 Жыл бұрын
Good question
@TeamAI. Жыл бұрын
@@Midblur09 it may be the airpods video but i’m not super sure
@TeamAI. Жыл бұрын
@xRhythm - ikr
@Ameerjanan Жыл бұрын
20 feet
@heavenlydusk Жыл бұрын
3 hours I think
@sythbtd7393 Жыл бұрын
Question: Where do you buy the screens that you use in repairs?
@congthanhtran1894 Жыл бұрын
Mobilesentrix they only sell to people who have phone business and valid tax id
@sythbtd7393 Жыл бұрын
@@congthanhtran1894 ok thanks
@heavenlydusk Жыл бұрын
Local electronics shop maybe? Idk, maybe online.
@bencrighton17 Жыл бұрын
IFixit
@gabrielmaranyo627 Жыл бұрын
Ifixit
@Music_R_Master Жыл бұрын
Everyone: yo that insane!😁 Apple: this is a game changer right there
@captainiosbeeswarm7432 Жыл бұрын
This is one of the coolest videos about iPhones I have watched.
@J_185 Жыл бұрын
Great vid👍 Question:what’s the worst repair tool you have
@Defaultnoobisme Жыл бұрын
I’m not much of a tech guy, so why do I find these so satisfying?
@Skkrtdav Жыл бұрын
Who also here has a cheap phone and has a 6000 mAh battery
@jaybuzz33 2 ай бұрын
Mine has like 3300
@gameplayzzstudio1432 2 ай бұрын
Mine was 5000
@Caelifera-fs8ed 2 ай бұрын
Mine has 0.1 :)
@user-xu4yy6rk7z 2 ай бұрын
5350 i got
@ProdipDas_05 2 ай бұрын
Moto g54
@Alt-Overload Жыл бұрын
The quality is good for me I’m just happy that you keep posting 😊
@cnvrtbl5 Жыл бұрын
So brilliant! Thank you for figuring this out - ohhhh the possibilities!! 😆
@duck8217 Жыл бұрын
This was insane!
@KingKobra49 Жыл бұрын
Hey. Life has got all those twists and turns. You’ve got to hold on tight and off you go. You will get through this.🤞🏽💯
@Robbie_Roy Жыл бұрын
@@jimmyfiredragon8582 its a bot
@jimmyfiredragon8582 Жыл бұрын
@@Robbie_Roy Oh flip okay thanks. I'll delete the comment.
@AeroDogMusic Жыл бұрын
KZfaq asked me to rate ur comment lol
@rushy6269 Жыл бұрын
I love this kind of technology videos ❤️
@CrownPointeChroma Жыл бұрын
Phone repair Guru is the master of fixing phones!
@GarbanzoBeansFan Жыл бұрын
Modding too
@jorgen1892 Жыл бұрын
uh, no.
@M_T_G_Leestar_8 Жыл бұрын
Keep the hard work 💪 your videos are the best
@arnavbule Жыл бұрын
This is exactly the content i signed up for !!!!! Need more of such stuff
@Petesplaceunboxing Жыл бұрын
Dude I absolutely love your videos! This was actually pretty freaking cool!
@maheen- Жыл бұрын
All Batteries that are made up of Li-ion technology have the same characteristics when considering the voltage. i.e 3.8v = 50%, 4.2v = 100% above 4.2 = explosion and below 2.9 = dead etc. so, you can swap anything with anything. Always make sure that the BMS board is compatible. that's all it need.
@Blu35cr33n Жыл бұрын
Just a thought… at the end you said you might drill a hole in the back for the battery. But a cleaner look would be to 3d print an edge piece that the screen and the back can snap to. Make the edge thick enough and the new battery looks like it could fit inside the phone. You’d end up with a chunky iPhone but 10ah would be worth the extra thickness.
@SirJJKongTheFourth Жыл бұрын
My thoughts exactly
@lidyademessew3548 Жыл бұрын
Hello again I am excited to see u again. Ur videos are amazing and cool. Thank you!
@bondjames5249 Жыл бұрын
I really want to attach the phone to power bank, keep doing we love your content)
@Roshan_420 Жыл бұрын
So you could 3d print a case and use a MASSIVE battery? I’d love to buy such a case. Perfect for hiking.
@TheRunawayCreeper Жыл бұрын
I mean this is cool, but there already are iphone cases that do this.
@hulkmarcopolo Жыл бұрын
Best thing would be to 3D print a back that can accommodate the battery.
@louisscatframe6062 Жыл бұрын
Your videos are amazing you inspire me
@jasonbournexX44 10 ай бұрын
Finally i found this kind of video. I will try this on my older phones
@x_4zxin243 Жыл бұрын
The better version of the energizer phone 😂
@jespermattsson2297 Жыл бұрын
I did this to my old androids Sgs2, sgn4, a70 and a few tablets as they are making timelapse videos and should survive poweroutages while running hard. The sgn4 i modded because i was using it hard and used 3 metal-cased lipos on the back with cosmetic and somewhat protective plasticcasing. Used it ss a daily driver for 3 yesrs in that condition adding 3 years of life to the device as the batteries was getting hard to get by bc of the devices age. Used it for a total of 6,5 years.
@kyryloreznykov4959 Жыл бұрын
Are there any risk that we exclude a power bank controller from the electrical circuit? I thought to do the same thing with my old Samsung but to solder it to a power bank output instead of direct connection to a phone bms board
@Monkey_D_Luffy56 2 ай бұрын
Would you mind doing a tutorial? I wanna do it on my old phones too
@tanvirahmed3089 Жыл бұрын
This video helped me very much because if my phone battery dies I will definitely do this.
@Techbin-yn6wr Жыл бұрын
we'd love a tour of your workshop/setup! :)
@TheSpotify95 Жыл бұрын
This looked like an awesome experiment, personally I wish phone manufacturers would forget trying to make the thinnest device possible, and instead just offer the best performance and battery life possible. A phone with 10,000mAh battery would be insane (plus it would then have the thickness to offer headphone jack, expandable storage, and basically every other feature that was useful, but has since departed us).
@TabbyEgg312 Жыл бұрын
yeah i like thick phones alot
@muhdaimanharith Жыл бұрын
You should use ulefone or oukitel smartphone..
@wearefromserbia9714 7 ай бұрын
@@muhdaimanharith if only they offered quality near other manufacturers
@willh6235 2 ай бұрын
Check out the Unihertz Tank. It has a 22,000 mAh battery
@Zoltan. Жыл бұрын
Hey PhoneRepairGuru, i was just wondering from where do you buy all the replacement stuff and screens?
@ceticx 5 ай бұрын
He gets it from mobilesentrix, but their generally more business oriented, for person I would use injured gadgets, or ebay if you feel like searching for oem and stuff
@Perfection100 Жыл бұрын
I Am Addicted To Your Videos!
@Sibani_Das Жыл бұрын
This is super crazy, waiting for part 2.
@shashankgupta7571 Жыл бұрын
Hey phone repair guru , can you run a accubattery test to see wheather the iPhone is determining that the attached battery is of 10000mah
@marwanwael9070 Жыл бұрын
Now we want part 2 with 3D printed housing to make it actually a working iPhone ❤️❤️ Keep it up 👏🏻👏🏻
@floskyy66 Жыл бұрын
Love content bro its helped me repair my iPhone its like a Tutorial
@emmanuelbinen6554 Жыл бұрын
I like the way he constantly repeats so...so...so... I'm like waiting for it 😁
@sudoAnalytics Жыл бұрын
Loved this one 🤩 I wish I could do something similar with a cheap android phone too ( I run python codes on them in loop for days).
@John-zp2jm Жыл бұрын
You’d still need to keep them connected
@sudoAnalytics Жыл бұрын
@@John-zp2jm But I can move around different cities, without worrying about charger, power bank… I will be the happiest person to get a 20000 mAH power bank running android 12🫥
@John-zp2jm Жыл бұрын
@@sudoAnalytics lmao it’s still a lithium battery at the end of the day, it would only last 1 day
@jaydonrr744 Жыл бұрын
What’s poppin ☺️
@peterpp_t 11 ай бұрын
Pop corn, y..?
@Bestytever14 Жыл бұрын
Bro I remember back when you had 10k I like your videos :)
@johntuason Жыл бұрын
I always watch your videos! Keep it up! From PH
@guruoo Жыл бұрын
I'm just going to 3d print a case that can hold both my phone, and a power bank.
@ganotgame4310 Жыл бұрын
smart😂only if he thought of this and he wouldn't be wasting so much time on connecting the phone to the battery
@SOTP. 9 ай бұрын
But then you are charging the powerbank, which then charges the phone... but other than that, it works.
@snoxeno0753 Жыл бұрын
Battery life will show up as 1000% capacity 😂
@TKKG420 6 ай бұрын
bro keep makin videos man your an amazing youtube
@andyvitz Жыл бұрын
Yeah I can’t wait to see you do that man
@jindrasmutny4181 Жыл бұрын
I strongly recommend getting longer wires than drilling the iPhone body 😁
@Gerkozielman 11 ай бұрын
Fun experiment. I'm just wondering if overcharging (well maybe not overcharging, but more a charge problem ;-) is an issue here, since the capacity of the new battery is much larger.
@hanktank45 Жыл бұрын
This is awesome, can't wait to see a follow up
@7amidou84 Жыл бұрын
Bro im wating for pt2 keep it up🤙
@CidKagenouNotShadow Жыл бұрын
I just had this idea where the iPhone using (external) batteries instead of having internal batteries. It would've decreases the amount of heat when you're playing games and not to forget the weight too. Just wondering whether long cables/connector affect the power delivery to the logic board.
@ceticx Жыл бұрын
@@androidmaster3369 batteries dont explode when they touch dust
@deleqtronica8733 Жыл бұрын
At that point why don’t you just get an Asus gaming phone if gaming is one of your top priorities?
@cinematica9073 Жыл бұрын
First of all, I love your Videos. This is a funny idea but it seems like you have missed something very important. The Battery from the Powerbank has a nominal voltage of 3.7V and a voltage of 4.2V when fully charged. The Iphones Battery however has a slightly higher Voltage of 3.8V and around 4.4V when fully charged. That means if you charge up the Battery with the Iphones BMS you will overcharge it and it could be a fire hazard. Even though both are Lithium Ion-Polymer Batteries they have different voltages per cell.I have encountered this voltage problem myself as I did the Same you did with a Galaxy s7.
@surapurna Жыл бұрын
what if we using phone battery with the same spec but higher capacity?
@cinematica9073 Жыл бұрын
@@surapurna thats possible but sadly there are many sellers who rebrand normal or even used batteries as higher capacity. It is possible to make a fitting cell with a slightly higher capacity but you still have the physics of a battery that limits its capacity. Else we would have much bigger capacity batteries in our phones:)
@surapurna Жыл бұрын
@@cinematica9073 like a tablet battery for example. Or just stack double triple the same exact battery in series
@cinematica9073 Жыл бұрын
@@surapurna Yes but you need to connect them in Parallel and not in series. If you connect them in series the voltages are getting added up
@cinematica9073 Жыл бұрын
If you want to increase the capacity you have to connect the cells in parallel.
@papervws Жыл бұрын
that is really impressive. nice one!!
@dr.butter4235 Жыл бұрын
like uploads like these when you actually get inspiration foran idea instead of burning out cranking continuiously
@BlackGokuSolos Жыл бұрын
plays rtx on
@khamigen Жыл бұрын
This is extremely dangerous as the iPhone charges its batteries to 4,35V whereas standard Power bank and regular liion batterys only charge to 4.2V. By connecting the wrong bms you basically left the battery at the iPhones mercy. It will probably attempt to overcharge it and could destroy the cells, resulting in a blown Battery and a fire hazard. If you attempt this, watch the cell chemistry and rated voltage before soldering a foreign bms to it.
@oliverkwin3980 Жыл бұрын
I’m gonna try this 👍🏾👍🏾👍🏾 Good one bro
@waelm0611 Жыл бұрын
You are dope bro! Damn , thank you so much, subbed
@i_like_phones Жыл бұрын
First
@HuseynRadjabli 10 ай бұрын
You're a genius, bro!
@kangaroo0177 Жыл бұрын
I love all your videos so much
@SAGAMERJOSH6808 Жыл бұрын
Do it YOU HAVE TO BRO u got me excited AND GLAD U BACK I HOPE FOR MORE VIDEOS PLEASE
@ELOGs1 Жыл бұрын
Nice one Cant wait for the results
@theknightmare2796 Жыл бұрын
That's why I love your videos
@mahammedanas6500 Жыл бұрын
Can't wait to see what are you going to do next 😆😆
@techdegenerate Жыл бұрын
pretty cool idea! thanks!
@Jaden--04 Жыл бұрын
Love what u do broo👏👏👏question though have u ever fixed a tecno camon x before
@Joseandresnajera Жыл бұрын
Good to have you back man.
@xasdz6311 Жыл бұрын
Your quality is great 1080p60 is amazing also great videos!
@nemanjabozovic566 Жыл бұрын
Great video!
@syedasrar8420 Жыл бұрын
I love tech so much and I want to meet this person some day.. In Sha Allah
@thisberandom Жыл бұрын
@Peter Knetter should make a fancy schmancy cardboard housing to keep that bad boy together in style
@netnael.m Жыл бұрын
I did it with 4 18650 batteries on the Samsung S4, cool video BTW.👌
@ianconklinmusic Жыл бұрын
I was just thinking about if this was possible. It’s my lucky day.
@xenvector Жыл бұрын
I love what you’re doing
@tavlogs6420 Жыл бұрын
Niiceee Now it'll last a full day's of usage like a normal phone!
@CyanideLucifer Жыл бұрын
I wonder how far you can go in terms of housing and "hardware hacks"... btw you're my favorite KZfaqr love your content 😎
@cooltool.nem.n.nem. Жыл бұрын
Yes!! This is the video that we needed!!! 😎😎😎😎😎😎😎😎😎😎😎😎😎
@dolanD2 Жыл бұрын
This is awesome!
@ehsanullahhakimi6150 Жыл бұрын
You are doing what I want to do with my iphone! because you may game on this phone whole day
@aimerboy69 Жыл бұрын
LOVED IT
@freddybernadino8201 Жыл бұрын
Favourite KZfaqr 🇿🇦🚀🔥🔥
@mphodanielkgole2172 7 ай бұрын
The camera quality is perfect
@homo189 Жыл бұрын
I've been doing this from my past android phones just to have a long lasting battery and it really works.
@grooom21 Жыл бұрын
Hahaha pure gold. Love this kind of crazy ideas. If you can keep on going.
@Cherrie_The_Furry 10 ай бұрын
Interesting, I will like and been subscribed :)
@xLastxTemplarx Жыл бұрын
Welcome back! :)
@Ramoooio Жыл бұрын
Crazy vid btw these are so interesting
@snow15243 Жыл бұрын
I have that exact same helping hands thing!!
@greg8214 Жыл бұрын
The quality is very good
@mobiltosse Жыл бұрын
Dude, that is great😀
QAZSPORT TV / ҚАЗСПОРТ TV
Рет қаралды 196 М.
SMOL Italian
Рет қаралды 6 МЛН
Hugh Jeffreys
Рет қаралды 4,1 МЛН
Strange Parts
Рет қаралды 3,8 МЛН
Penguin DIY
Рет қаралды 2,9 МЛН