PID Control in RsLogix 500 for Allen Bradley Micrologix and SLC

Рет қаралды 36,823

Күн бұрын

In this lesson we go through how to configure a PID instruction in Rockwell Automation's RsLogix 500 for the Allen Bradley Micrologix and SLC PLC.
View our entire PID Proportional Integral Derivative Lesson Series at twcontrols.com/pid-control-pr...
Items used in this video:
PLC Trainer twcontrols.com/plc-trainers
PID Trainer controls.tw/pidtrainer
Analog Simulator plctools.com/analog-simulator...
The above links make these videos possible. Please use them!
Support these videos while you advance your skills courses.twcontrols.com/

Пікірлер: 62

@alvieteal4980 9 ай бұрын

This is so much easier to do in c+ I needed this video. Thanks man.

@augustograton8958 3 жыл бұрын

Thank you Tim !

@TimWilborne 3 жыл бұрын

You are welcome Augusto.

@jesusandresgonzalezventura2449 Жыл бұрын

gracias por tu video eres una persona en la que confio desde el punto de vista tecnico. siempre tomo muy en cuenta todo tus videos y a la verdad me has ayudado bastante en mi carrera

@TimWilborne Жыл бұрын

¡De nada!

@mdabdurrashid2504 3 жыл бұрын

Your video's are really helpful.👍👍👍

@TimWilborne 3 жыл бұрын

You are welcome.

@jimbass924 3 жыл бұрын

Great content!

@TimWilborne 3 жыл бұрын

Thanks!

@DavidMoaiki 8 ай бұрын

very good example for PID Control

@TimWilborne 8 ай бұрын

Thank you!

@mdabdurrashid2504 3 жыл бұрын

Thanks for sharing this types of useful video. If passiable then please make a video about Modbus protocol with Allen-Bradley PLC.

@TimWilborne 3 жыл бұрын

We have some coming.

@geoffgroth7355 2 жыл бұрын

hey Tim, are the rest of the videos for PID on the 1100 available somewhere? I cannot seem to find them anywhere....

@irenioretamal6394 2 жыл бұрын

👍👍👍

@irenioretamal6394 2 жыл бұрын

👏👏

@alvieteal4980 9 ай бұрын

I’m doing a project with triac driven heaters and I’m very unfamiliar with rs studio.

@TheBetooz 3 жыл бұрын

ohhh this is incredible ! crack!

@TimWilborne 3 жыл бұрын

Glad you think so!

@renaco1145 2 жыл бұрын

Any idea why I can't read my process value when I am monitoring PID setup screen? The related register assigned as PV in the PLC, takes values with no problem. I can read scaled error values. Thanks.

@lalitpandey8023 3 жыл бұрын

Sir please share , modbus protocol and different type of datatypes to decimal conversion in studio 5000

@TimWilborne 3 жыл бұрын

We are going to lightly touch on that in an upcoming video.

@nematalla1 3 жыл бұрын

Can we have a video on allen bradelly safety relay and how it is connected to light curtains and e-stops

@TimWilborne 3 жыл бұрын

Check out this video series. twcontrols.com/safety-plc-lessons

@kennalindia5604 3 жыл бұрын

Hi Tim Have you got a video of a batch process mixing with weight control

@TimWilborne 3 жыл бұрын

No, that might make an interesting video.

@chintanbeladiya1058 10 ай бұрын

First thanks tim sir to this video. About Allen Bradley 1100 next PID video is not avaliable? Is that video avaliable anywhere?

@TimWilborne 10 ай бұрын

Here are all the PID videos I have done so far twcontrols.com/pid-control-proportional-integral-derivative

@jacobhinton3201 5 ай бұрын

How would I get the scaled value without being able to just turn the fan speed all the way up and see where the ball is? Like if I had a tank that I was trying to get the level for and there was a level indicator, how would I go about getting the full value of the tank without actually filling it up to see what numbers I’m going to get back from the level indicator input?

@TimWilborne 5 ай бұрын

You would find the high and low setpoint on the documentation.

@marshal7102 6 ай бұрын

When configuring the PID rung I opened the Type drop down and there was no PID to select ???? What Now?

@dannyassmann7331 Ай бұрын

Is there a good way to 'initialize' the PID output? A way to keep it from always starting up at its lowest value or ramping up to its highest value if its the controlled device was shut off? For example: always having a pump start up at 30% speed and then the PID starts adjusting from there.

@TimWilborne Ай бұрын

Yes there is, I'm getting ready to pick back up on PID videos and will cover it.

@shawnspencer8766 3 жыл бұрын

At 10:30 you're using a move instruction to the analog output, but I noticed it's an integer. I tried doing the same thing, but used a floating point to get more accuracy, but the analog output just rounded up or down. Is it possible to use a floating point for analog 4-20mA output?

@TimWilborne 3 жыл бұрын

No and we've brushed on this in several videos but I don't know that we have ever addressed it directly. While analog is "infinite", the it comes into the PLC as digitally with a certain bit resolution. In the case of the Micrologix, it is 12 bit resolution which means that it chops the full scale into 4096 increments. Now someone will probably come along and correct me and say that the Micrologix is "15 bit" resolution since its scale 0-32760. However, the Micrologix shifts the data by 3 bits, ignoring bits 0, 1, and 2 and placing the data in bits 3-14. I should do a video on this...oh wait, as I type this I remember I wrote an article about this. See link below. www.theautomationstore.com/rslogix-500-analog-bit-resolution-and-precision/

@shawnspencer8766 3 жыл бұрын

Tim Wilborne great read, thank you for the reply!

@juninhoaraujo6107 Жыл бұрын

Como resolver a falha "Ponto de definição de PID fora da faixa." No rslogix 500?

@TimWilborne Жыл бұрын

Sounds like your set point is outside of the minimum and maximum range.

@sarthakmohanty2694 3 жыл бұрын

When you will upload br regarding Modbus communication between energy meter & plc with data swapping.also how to show the energy consumption in scada

@TimWilborne 3 жыл бұрын

Maybe, we don't typically get into SCADAs on this channel but we do have a small HMI/SCADA series coming that we might cover that in.

@sarthakmohanty2694 3 жыл бұрын

@@TimWilborne thanks tim.please I am waiting for it

@azeemahammed8646 3 жыл бұрын

hi, how to store data in a .csv file,for every batch of the product, please respond?

@TimWilborne 3 жыл бұрын

Not enough info, many different ways depending on the hardware.

@infusedpower 3 жыл бұрын

You said F8:1 was an unused floating point number but it became the input for the scaled with parameters function. Where does the F8:1 obtain its data value if there is not a function outputting to that data storage? How does F8:1 become and input when it is just a register? In the previous SCP F8:0 was the output.

@TimWilborne 3 жыл бұрын

Shooting from the hip since I didn't watch it before replying but wasn't F8:1 the level set point? This is the desired level for the PID and we manually enter it. The 2nd SCP scales the value which we entered via the data table to PID units.

@stephenj1539 Жыл бұрын

Thanks Tim for your great work, do you please mind clarifying the use of the F8:1 float and it is unused and it's still puzzles me where it's getting its input from. I would have expected you to use F8:0 rather. Thanks

@fernandovelasco4904 Ай бұрын

Do you sell the PID bench testing unit?

@TimWilborne Ай бұрын

It is from PLC Cables, here is the link controls.tw/pidtrainer

@gaisonsunday9547 3 жыл бұрын

How Can someone enroll With ur program

@TimWilborne 3 жыл бұрын

See link below. twcontrols.com/plc-lab

@vincentooko6205 2 жыл бұрын

Can rslogix 500 emulate simulate a PID control.

@TimWilborne 2 жыл бұрын

Not without a lot of work, you will need some hardware.

@vincentooko6205 2 жыл бұрын

@@TimWilborne Thank you Sir. So I have weighed my options and presently I believe i can manage the " a lot of work". That is considering the hardware alternatives. I have been doing bits and pieces on SIEMENS TIA portal(works great). I believe with some research and lots of your help, it may just work . Thanks again.

@edgarocopio5186 9 ай бұрын

Friend, i can't put on play My pido loop, do every step for go on, i'm work under emulador 500, may You help me?

@TimWilborne 9 ай бұрын

The most common problem is not having any values in your parameters

@edgarocopio5186 9 ай бұрын

Thanks Tim, CV% don't move, the imput, pv is in play also not out from block pid

@TimWilborne 9 ай бұрын

But what are your variables set to?

@nisrnisr5980 3 жыл бұрын

First, I thank you for this video Secondly I have a question What is the difference between raw/proportional scale and pid scale ?? and Are the binary Scaled numbers is fixed for all modules 1762-IF4 and OF4 and IF2OF2 for the two option raw/proportional and pid ?? Meaning is the numbers 0 to 32767 is constant for 1762-IF4 and OF4 and IF2OF2 when i configured raw/proportional Or it differs from one module to another and the same thing with PID scale configuration for analog input/Output

@TimWilborne 3 жыл бұрын

PID scale is 0-10,000. The raw formats of those three numbers are the same but it is good to check because not all of them are the same across the Micrologix line. Check out this link. www.theautomationstore.com/rslogix-500-analog-bit-resolution-and-precision/

@nisrnisr5980 3 жыл бұрын

@@TimWilborne thanks