Pin Peening vs. Rivet Peening Explained

Рет қаралды 20,972

3 ай бұрын

What is the difference between pin and rivet peening? Boat builder Bob Emser explains both methods and where they are used. He also demonstrated both by using a bronze block cheek and the boom's gooseneck fitting.
“If you’re going to make it, make it beautiful.”
Bob Emser
Interested in building a boat with me? Check out my online boat building course.
www.boatbuildingbootcamp.com
Subscribe for more Boat Building from The Art of Boat Building:
kzfaq.info...
Share this video with a friend:
• Pin Peening vs. Rivet...
How to support The Art of Boat Building.
Purchase Official Merchandise here:
www.bonfire.com/store/the-art...
Become a Patron:
/ theartofboatbuilding
Watch next
Recommended Playlists
Building Victoria. Arabella's Tender
• Season 3 - Victoria
Carvel Planking Playlist:
• Carvel Planking
Haven 12 1/2 Playlist:
• Season 2 - Haven 12 1/2
Tool Making:
• Tool Making
Let’s connect:
Facebook:
/ bobemseramericansculptor
Instagram:
/ artofboatbuilding
Linkedin:
/ bobemser
Bob Emser American Sculptor:
www.bobemser.com
#theartofboatbuilding #artofboatbuilding #makeitbeautiful#woodenboatbuilding #buildingasmallboat #buildingasailboat #shipwright #toolbuilding #Haven12 #herreshoff #shipwright

Пікірлер: 41

@JCSalomon 3 ай бұрын

Obvious (to me) follow-up question: When would you use one method vs the other?

@jorgenr 3 ай бұрын

Rivets have much better holding power, but are very difficult to get as flush as the pins. In applications where aesthetics or smoothness matters more than holding strength, a reamed hole makes more sense. You can do counter sunk flush rivets too, but there are harder to get a nice finish with.

@davidyendoll5903 3 ай бұрын

I was amazed at how the pins disappear . Make it beautiful ..... done .

@SavingMaverick55 3 ай бұрын

As someone who commented on this in the last video, I didn't realize that you were doing any reaming to the holes in the cheeks and was worried that the assembly might loosen up under strain. This totally clears it up for me. Thanks for the explanation! Great content, as always!

@jcwebb4now 3 ай бұрын

Me either. It seemed like just pin peened without tapering would pull out. Thanks for the video Bob. Very informative!

@lanesteele240 3 ай бұрын

Bob of here hammering the facts out

@jackdotzman2908 3 ай бұрын

You’re fun to watch and I never fail to learn something new. Thank you. From Missouri

@drop_dtuned6167 3 ай бұрын

Well happy Tuesday, and an Art of Boat Building episode to go with my coffee. Nice!

@glencrandall7051 3 ай бұрын

OK, I understand the difference between the two types you demonstrated. How do you determine which type to use? Also what about rivets with domed ends? When do you use that type and why? Or why not? The blocks you are making are beautiful. I voted for wood. I want to change my vote. The bronze is absolutely outstanding. 👍👍 Thank you for sharing. Have a great day and stay safe.🙂🙂

@mjkarwath1 3 ай бұрын

While "We" all know your pins had shoulders from watching your previous beautiful block work, your cool little sketch did not depict them. Thanks so much !

@davidc6510 3 ай бұрын

Another great AOBB Bob. If you are not careful sharing your secrets then everyone will be making beautiful items just like you. Thanks for sharing!

@terrybrower3437 2 ай бұрын

You can teach an old dog new tricks. Reminds me of near 70 years ago when my dad taught me how to rivet new sections on the hay mower.

@desertpoj 3 ай бұрын

Really excellent. A beautifully simple video delivering an outstanding lesson.

@terrybrower3437 2 ай бұрын

What ?! A tool I don't have? Now I'm shopping for a long taper reamer. Thanks for the excepttional videos.

@tomtruesdale6901 3 ай бұрын

Great class Bob, thank you for doing this.

@michaelbinion2555 3 ай бұрын

Your printing takes me back to my drafting days. Your style is quit similar to mine. Seeing your construction lines is what attracted my attention to your lettering.

@terrybrower3437 2 ай бұрын

Also reminds me of drafting class in paper and pencil over 60 years ago in high school.

@scrappybobbarker5224 3 ай бұрын

Your a class act Bob, i really enjoy your videos. I am learning so much from you. I will be building a small workshop soon and stripbuilding a canoe or dory. I have a tupperware canoe i would like to fit a sailing rig to, so these videos are giving me lots of good ideas. Thanks from Arizona.

@stevekelley1179 3 ай бұрын

Good job explaining the difference between the two.

@MCsCreations 3 ай бұрын

Really interesting indeed! Thanks, Bob! 😃 I didn't ask or anything, but I was wondering about it during the last video! Stay safe there with your family! 🖖😊

@doughowden1098 3 ай бұрын

Hi Bob, great site, I was taught never to reverse a reamer, always turn in the cutting direction for accuracy and to preserve the reamer cutting edges

@TheArtofBoatBuilding 3 ай бұрын

You were taught correctly. As you know the reamer only cuts clockwise. When I reversed it was not cutting. (bad habit) For the video I should have removed and reset. It's a bit like using a mill file, it too only cut on the out stroke yet many of us drag the file back over the work. Thanks for your comment and watching. Bob

@user-ss7tu3gh9z 3 ай бұрын

An additional explanation of the mechanics of the two fastening styles might have been helpful to some. Correct me if I'm wrong, the rivet peening relies on the preformed head at one end and the deformed head on the other end to hold the rivet in place. The preformed head on one end and the deformed head at the other end create physical barriers preventing the pin from traveling in either direction. Where pin peening is causing a press fit condition of the pin to each cheek. The press fit condition enables you to grind down the deformed pin end and still have pin retention.

@toddwheeler1526 3 ай бұрын

Another beautiful video sir of a true master craftsman. Thank you so very much for your service and time that you give back to the community.

@TheArtofBoatBuilding 3 ай бұрын

Thank you very much!

@danpatch4751 3 ай бұрын

Very good demonstration. 👍

@thomaswilhelmsen6219 3 ай бұрын

So I understand the difference between the two, but when should you use one and not the other?

@stevenlengyel9701 3 ай бұрын

I believe it depends on the hole

@gritz1701 3 ай бұрын

Great vid

@weswright3187 3 ай бұрын

Thanks for that. It all makes sense now 🙂.

@matthewlang8320 3 ай бұрын

If it were me, I’d show holding the block just like you, but after a few seconds, time lapse/jump the video to more peening were I’d have blackened my thumb nail with a sharpie. Maybe a suggestion for April fools day. 😂 Seriously though, very informative video. Thanks.

@TheArtofBoatBuilding 3 ай бұрын

good one!

@SkylerinAmarillo 3 ай бұрын

But you don’t say which is better or why you wouldn’t make the rivet peen flush or when you would use one over the other. I knew nothing about this but NOW I do have questions! :)

@coastalgeorgia6558 3 ай бұрын

thanks. to an uniformed like myself it would seem that the pin should be countersunk and the rivet wouldnt need to be... why isnt that the case?

@SavingMaverick55 3 ай бұрын

I was wondering this too. It would seem like you would only need to countersink a rivet if you wanted to grind it flush with the surface.

@baalbor7050 3 ай бұрын

👍👍⛵⛵⚓⚓⛵⛵👍👍

@dwaynekoblitz6032 3 ай бұрын

Try saying that three times in a row! 😂

@stuartwilliams1790 3 ай бұрын

I disagree with your explanation of riveting, as an engineerung apprentice we were taught that the first actioin in riveting was to "upset" the rivet with the flat face of the hammer, so as to expand the body of the rivet in the the hole so that it becomes a very tight fit in the hole and not as you said clearance

@TheArtofBoatBuilding 3 ай бұрын

That is exactly what I did. I mentioned using the flat side of the hammer first. This video was not meant to be a tutorial but an explanation of the difference. There has to be a clearance for the pin to fit in so that the peened pin can expand into the reamed clearance. Thanks for watching.