I used 6v dc as power input. Led - and ground pin are connected together. Trigger (two types) 1.Non-repeating (doesn't count movement when led is on) 2. Repeatable (counts movement when led is on and output duration increases)
Пікірлер: 133
@ABID57 ай бұрын
কম দামে সেন্সর টি কিনুন এখান থেকে click.daraz.com.bd/e/_CUT5Ii
@soktahu6765 жыл бұрын
Why my pir sensor always made the led light up?
@keplaris24014 жыл бұрын
My PIR module doesn't react to movement. Should I replace it?
@salvindevtale3992 Жыл бұрын
Yes
@moizwayne4 жыл бұрын
Can i connect 3.6v water pump using 9v battery. With out resistor transmitter 0oz help
@aijazahmed9113 Жыл бұрын
I recived pir sensor without jumper conection how l fix this pl guide me thanks
@padmanabhanr42425 ай бұрын
How to increase the time delay between first and second sensing for example to 30 or 60 seconds?
@dertutorsdersaurabh21705 жыл бұрын
After connecting pir module led is continuously getting on off without any motion
@ashutoshmallikakaraj5273 жыл бұрын
remove the jumper completely and test it . . same issue with me but solved now . . .may be it ll help you as well . . . good luck
@8dsonglovers8823 жыл бұрын
sir apne jase bata ya vese led lagaya per apne app chalu bandh ho raha hai kya karu
@arunnair41303 жыл бұрын
@@ashutoshmallikakaraj527 didn't understand
@sanjoymazumdar-iz3rs Жыл бұрын
dada may Amazon ka 230 volt Ac motion sensor ke sath buzzer lagaya, 4diod brize bany aur positive negative ke sath 220uf 25 v condencer aur AC negative ke sath 68k resistant lagaya. jab sense hota hay tab loudly bajta hay, lekin har bakt ek low kuuuu... noise hota hay. ap bata sakte hay kaise e low kuuu... nosise bondh hoga
@shahadathossain99827 жыл бұрын
how to adjust those two sensitivity and duration ✌✌
@natarajansrinivasan9402 жыл бұрын
0⁰⁰⁰
@ethicalhacker12 жыл бұрын
With a screwdriver like you would turn a screw with a screwdriver
@Filcoka7 ай бұрын
you are the best!
@MrRamtahiliani19 күн бұрын
i have connected circuit but my pir censor is nor working only light gets on what is the poblem
@ABID519 күн бұрын
@@MrRamtahiliani what is the supply voltage?
@vipinkp47305 жыл бұрын
How much dc volte use ing for testing
@ABID55 жыл бұрын
5v adapter
@MohamedAshraf-bt3vc2 жыл бұрын
What is the Maximum volt i can give there ?
@ABID52 жыл бұрын
12v also
@sammy28885 жыл бұрын
Hi good video , can i use this sencer to my 18w driver led ceiling lights .pse help .. tks
@ABID55 жыл бұрын
Yes. Follow this circuitdigest.com/electronic-circuits/automatic-room-lights-using-pir-sensor-and-relay
@pratikjoshi72073 жыл бұрын
It's working Thank you
@Marpacifico2 жыл бұрын
Thanks, it is working.
@himanshupatil45486 жыл бұрын
can i use led bulb instead of small led light
@ABID56 жыл бұрын
kzfaq.info/get/bejne/f89gg5qT3K6lc6s.html
@kylefrancisbanares91335 ай бұрын
why others use relay if it is working without what the use of that relay
@RK-kl3lz4 ай бұрын
1. If you want to control AC - stuff like 110/220 Volt - bulb or even some appliances 2. OR if you want to run some DC motor Directly it is barely enough for some Led but even then good to use some NPN transistor like 2222N
@8236310 ай бұрын
It can prevent working accident.
@Sajanepal24 Жыл бұрын
My pir sensor auto give output after around 1 hours.can you tell me the solution
@ABID5 Жыл бұрын
What kind of power supply you are using? What's the voltage?
@Sajanepal24 Жыл бұрын
@@ABID5 i give 5 voltage by using stepup module from lithium battery.
@robertknott11243 жыл бұрын
What power is being used here ?? It shows no connection to anything. If mains power is being use it is pretty unsafe to my observation.
@ABID53 жыл бұрын
See description
@dj_sorra8605 Жыл бұрын
For 5v led what power you need?
@misbahofficial2025 жыл бұрын
It nmanya soket ap gan yng d kbel menuju sensornya
@areebabdullah50014 жыл бұрын
I want to connect this same sensor to 12v water pump is it possible? If yes please guide me..
@ABID54 жыл бұрын
similar concept envirementalb.com/motion-sensor-light-switch/
@areebabdullah50014 жыл бұрын
@@ABID5 thank you so much.. last question should connect 12v power adapter to relay bcz my pump is of 12v
@ABID54 жыл бұрын
yes,
@MrNams3 жыл бұрын
My PIR module alwyas give high voltage? equivalent to input vcc
@ABID53 жыл бұрын
Some faulty modules maybe
@muhammadsulamanhashmi56164 жыл бұрын
Aslamuaalikum, Bhai is my Trigger ka kiya kam ha? zara explain kr dyn: m chahta hun k agr Room m enter hon to LIGHTS on ho jayn aur jb tk room m rhy lights ON he rhy: aur agr 1 sy zyada persons room m hon to lights on he rhy aur jb tk last person room sy bahir nahi jata lights off na hon. Please is m kch help kr dyn: Shukriya Sulaman Asif From Sialkot.
@ABID54 жыл бұрын
This sensor Doesn't support such a condition.
@unclepaul8331 Жыл бұрын
What is this, put the diafragm for learn peoples🤔
@bishwajitperfection36336 жыл бұрын
Can i connect buzzer in place of LED
@universallentertainment50186 жыл бұрын
Desi Editing yes
@chandanomkar2 жыл бұрын
What did you do with gnd? I did not understand that part.
@ABID52 жыл бұрын
Sorry for earlier reply it was for another comment. Gnd meant the negative terminal of the module, we will connect it to power supply ground(negative pin)Also the led negative goes to power supply ground / negative pin.
@ayodhya74004 жыл бұрын
this sensor detects ambiant light or not?
@ABID54 жыл бұрын
not
@DivyanshuPantluvuall7 жыл бұрын
My output in LED is always showing High... Could you please tell me how to resolve it
@ABID57 жыл бұрын
cases : 1/Adjust the timer pot,may be it's set to maximum. 2/ Use more than 4 volts. 5v is good. 3/ Change the jumper connection. 4/Or Your module is defective .
@moniquemoniquemoniquemoniq14095 жыл бұрын
someone found this answer??
@bartpatton34092 ай бұрын
Anyone got answers?
@manystuff6 жыл бұрын
theres no need of relay , resister , transistor?
@ABID56 жыл бұрын
the video and title is about the """ Simple""" test
@Hyacinth-ff4eg Жыл бұрын
Where to buy this connector cable?🙏🏼
@ABID5 Жыл бұрын
It's called " Jumper Cables/ Wires " very cheap and available in any online electronic store
@surajjaiswal3016 жыл бұрын
2 se jyada bulb use kar sakte he
@ABID56 жыл бұрын
kzfaq.info/get/bejne/f89gg5qT3K6lc6s.html
@gnarlzafunk2thalore4 жыл бұрын
Hi what song is this
@ABID54 жыл бұрын
luu gia khang lau dai cat
@ratnotimur94824 жыл бұрын
Bi dimana ya dan kasih info
@technicaljd48236 жыл бұрын
How much maximum volt we can applied?
@ABID56 жыл бұрын
5 to 12 volts DC
@technicaljd48236 жыл бұрын
Thanks vi
@dj_sorra8605 Жыл бұрын
Powered at 5v what voltage does it output?
@ABID5 Жыл бұрын
3.3v
@dj_sorra8605 Жыл бұрын
For 5v out what should be done?
@ayoraz_0144 Жыл бұрын
@@dj_sorra8605 put it at 8v
@tejaskansara22765 жыл бұрын
My led continues glow in tedting
@ABID55 жыл бұрын
how much volt was applied?
@tejaskansara22765 жыл бұрын
@@ABID5 9v
@sontolie72936 жыл бұрын
My PIR doesn't sense any motion, help me sir.
@ABID56 жыл бұрын
May be it is damaged.
@sontolie72936 жыл бұрын
ABID Inc. I just ordered, it.
@sontolie72936 жыл бұрын
ABID Inc. Sir I did your simple test and when I connect it to the 5volts power supply it stop the current and when I wave my hand to it, the led light doesn't turn on. What is the problem sir? Please help me, this is for my project in school.
@ABID56 жыл бұрын
send pictures here : abidhasansaumik@gmail.com
@michelfrance755 жыл бұрын
This module has no sensitivity, a few tens of centimeters at best.
@ABID55 жыл бұрын
Some Chinese clones,cheap sensor from ebay has this problem; I've seen.
@michelfrance755 жыл бұрын
All these HC-SR501 modules are Chinese-made, including the one shown here.
@akshatsachanttb2 жыл бұрын
it's not working please reply
@ABID52 жыл бұрын
The output signal is very low be sure to check with a multimeter.
@Mztechgaming5 жыл бұрын
Arduino is used in this setup...?
@ABID55 жыл бұрын
No, It's just a simple way to test.
@qinxz29883 жыл бұрын
good music in the video would like to download it for yourself, share
@ABID53 жыл бұрын
kzfaq.info/get/bejne/eK6FedNizZ3Qiqc.html
@sunnyprateek91866 жыл бұрын
Bhai buzzer kam rate pe kaha milega online me
@ABID56 жыл бұрын
I'm not from your country, but this may help you : (Rs-14) www.xcluma.com/active-passive-buzzer?search=buzzer&description=true
@alfredanto055 жыл бұрын
@@ABID5 cmmon stop lying, you r an indian
@NirajKumar-bn3cu4 жыл бұрын
Sir mere project mein bulb toh glow ho raha hai lekin off Nahin ho raha hai
@ABID54 жыл бұрын
adjust the timer by turning the knob
@NirajKumar-bn3cu4 жыл бұрын
@@ABID5 knob turn on off Kar rahe hain par phir bhi bulb continuous flow ho raha hai
@NirajKumar-bn3cu4 жыл бұрын
Glow ho raha hai
@ABID54 жыл бұрын
could be the sensor is bad
@NirajKumar-bn3cu4 жыл бұрын
@@ABID5 sir do din pahle turn on off Kar ne par work Kar Raha tha lekin aaj Nahin ho raha hai kya relay mein problem ho sakta hai
@MrRamtahiliani19 күн бұрын
kindly reply
@LoneWolf-bl4mj6 жыл бұрын
what's the brown color?
@ABID56 жыл бұрын
negative of battery,
@michaelcarroll48325 жыл бұрын
To the author: Do you have a schematic of the connections? I am not sure the setup with all the wires connected. From your other replies, you are using 6 volts to supply power? Is that correct?
@dertutorsdersaurabh21705 жыл бұрын
Maine pir se led connect kia Vo bina kisi mition ke apne ap hi 3 -4 second me bar bar jal bujh rahi hai
@ABID55 жыл бұрын
what is the input voltage?
@dertutorsdersaurabh21705 жыл бұрын
@@ABID5 9 volt ki battery hai
@dertutorsdersaurabh21705 жыл бұрын
3-4 second me apne aap bilink kar rahibhai led
@ABID55 жыл бұрын
you need to adjust the delay time by turning the timer knob
@dertutorsdersaurabh21705 жыл бұрын
@@ABID5 ek bar full left kar chuke Ek bar right full kardia Ek bar bich vala ful kardia Light ki timing to change hoti hai lekin apne ap hi jalti hai apne ap hi bujhati hai, Ye problem hai Kya mera pir sensor kharab hai
@NirajKumar-bn3cu4 жыл бұрын
Please reply fast sir
@electron68076 жыл бұрын
How its range
@ABID56 жыл бұрын
20 feet
@dhamonsta5 жыл бұрын
Bilal Khan how it’s range? How does this make sense?
@mdalibmaris51754 жыл бұрын
LED...without current limiting resistor.....LED will suffer...
@ABID54 жыл бұрын
no. the output current of sensor is limited. so no need.
@hi-techgt50516 жыл бұрын
Can I use 220v ac
@ABID56 жыл бұрын
you need a dc adapter
@hi-techgt50516 жыл бұрын
A B I D where I get it
@ABID56 жыл бұрын
go in a shop brother
@hi-techgt50516 жыл бұрын
A B I D okay how to connect DC adapter
@micagloba88653 жыл бұрын
Can i use a 12v siren instead of led?
@ABID53 жыл бұрын
Yes, you need to use transistor/mosfet to turn on the siren.Follow the diagram i.ytimg.com/vi/ugDPdgGekNo/hqdefault.jpg