Hello from Michigan, I have found that if you don't want to go back over what you have plowed already ,speed is the key, it will help move the snow farther away from the blade. Also with a long driveway, go down the middle with the blade straight then angle the blade and push the snow to both sides.

Great job Adam and great assessment, reminds me of one I had on my 4 wheeler, learn the same details, great fun!

I had a rear three point plow on my tractor was great for backing up to doors step etc made by land’s pride I miss running it thanks for the memory

Take the teeth off your box blade and use it to drag in front of the garage doors. Plus use it to push backing up.

Flip your scarifiers around and the box blade is an awesome snow tool as well. Can doze it backwards, and clean up blade trails going forward. Can also get up close to obstacles like garage doors and pull it out. Will take a while to figure out the most efficient way to do your lot...... Montana Dan

I bet you're glad you didn't shorten the height of the blade. The snow was to the top most of the time. Russ. Esko, Minnesota

Plows awesome got one myself they are must have attachment if you get snow

Plow looks like its nearly perfect. It just needs some Red Bull. (that means wings)

I've always manually "edged" the buildings before plowing/blowing the snow. The time and effort it takes to do so is a lot cheaper than the mistake that will cost you. But that's just me. - Nice rig, I like it.

👍Looks like you have a pretty good feel for the newness of this project. Just like any other attachment; it will train you to its needs and capabilities..😎

Cute poppy.

Good stuff! U need a pick up with a plow on it.

I plow my driveway with a 12 hp lawn tractor and a 46" blade . Your tractor would probably be a little large for getting into the smaller places I plow and I have to push everything onto my property because not allowed to push snow into the street, but it gets done, if it is too deep I pull out the snow blower. LOL

Suggestion; Put sides on that plow and double its productivity.

You could’ve welded your quick attach plate further up on the A-frame because you don’t need to have a pivot on your Snow plow It looks like it works well

Works well. I haven’t got any snow yet but tomorrow it’s going to snow. I built a box blade going to try. I will post a video after that

I used to do this with my atv and a plow. Now I have a BX23S with a front end snow blower. I move the snow once. No moving piles anymore. I do like the plow that you have. I had to get off the ATV to angle the blade.

I have a snow blade for a skid steer loader. A few things that I have learned, some the hard way. On my skid steer the plow frame needs to be level with the loader arms all the way down so that the blade is always at the same angle to the ground. I just run the loader frame all of the way down. If the height of the back end of the snow plow frame changes it will change the blade height when sitting on the skids. I use a whole bunch of large flat washers to adjust the skid height. They are a bit expensive but it makes very fine adjustments possible. The extras are always up on top so they don’t get lost.

Problem with plows on FELs is they stick out to far and like to push the tractor sideways. As you use it more you'll probably find you can go faster than you think you can now and the plow works better at those speeds

Pushing snow w/ an open station compared to an all season cab is a night & day difference.

A lot of people gravel drives take a length of black pipe, use an angle grinder and cut a strip down the middle, then tack it onto the existing cutting edge, it certainly will save gravel but if you get 1" of snow then ice on top I dont thing you'll like the results of the front blade, although if you have a rear blade it should counter act that.

YOUNG MAN , WHERE I LIVE IN NORTHEAST LOUISIANA WHEN DOES SNOW HERE , REALLY OVER ALL , WE CALL IT ICE SNOW DON'T LAST LONG , BUT I THINK ONE TIME LAST ABOUT 4 DAYS ALL OVE LOUISIANA EVEN WAY SOUTH LOUISIANA TOO

A little tip from a old pro a little speed will help with rolling your snow and make it easier with moving the deep snow.

good job Adam on the plow. Western, Boss, Meyer etc wouldve charged obnoxious money for same concept setup. probably at less the quality to boot

what you need is a set of two ft wings on each side

I made the same thing for mine b series Kabota

This is why I just use my loader bucket. Gets the job done quicker. You can’t angle the dam things becuase the plow pushes the nose of the tractor the opposite way and not enough weight on steer tires

Lot less gravel this time. I really enjoy my rear blade for backdragging. Might be something to look into. 🤷‍♂️

Put chains on your tires. I have a small new holland 25hp4x4 and you can't stop it with the chains and a bit of skill. I love the angle blade I may have to get one and put the bucket and snow blower away.👍

I been planning to build one of these myself. I got a plow blade from a side by side. its missing all the attachment parts so I need to do some building of that part. I been putting it off now for 2 years that I have had the plow blade. its made by Warn. did you notice a lot of side forces pushing the loader frame right or left? that is my biggest concern is tweaking the loader arms with so much side force.

What was messing up the plow pushing was those front things on the plow THT make it stand

I am having a dilemma. I now have a case 1845 skid steer. I found a kabota B1402 M with a front end loader with a 4 foot bucket. It also comes with a 4 foot Roto tiller and rough cut mower. My skid steer is great for clearing snow but that’s basically all I use it for. I would definitely get more use out of the Kabota tractor. Any thoughts would be greatly appreciated. Would the Kabota be good for snow removal?

Makes me appreciate my mini skid after watching this.

Always push 2 rows out of garage and 2 rows opposite direction .....don't let wind rows to get bigger than 50% of height of blade id give you a c plus grade

Hi Adam...Im in the process of taking my old western plow setup and mounting it to a quick connect plate...I'm really excited... Do you have any fears of bending your FEL??..I see some people comment about this in other forums

Just think if you had a snowblower on the back of your tractor you be blowing the snow instead of pushing it into piles

Needs more practice on snow moving for sure

Great job. I’ve enjoyed using my new plow on my John Deere 2210. We made some videos of it if you get a chance to check them out, we’d appreciate the views. Beautiful blue sky in your area that day.

It appears you needed all the height of that blade.

Hopefully I'm 250 to join

Learn how to plow and build a boxend

Rookie mistakes. Watch others with experience for clues.

young man , u look like u are pretty tall have u every look at a bigger kubota loader tractor L2501 , BETTER STABLE AND BIGGER FRAME , HAVE GEAR DRIVE TRANMISSION because H S TRANMISSION HAS NOT MUCH POWER , IF I LIATEN TO ALL THAT " WHING" ALL DAY LONG I WOULD GO NUTS !

I'm sorry... Whilst I DO NOT CARE what color your hardware is, you NEED better hardware! Better hardware equates to LESS time 'cleaning up' and a MUCH 'CLEANER' clean!