Plumbing Tap & Sink Waste: Kitchen Part 7

Plumbing Tap & Sink Waste: Kitchen Part 7 | The Carpenter's Daughter

Рет қаралды 80,112

The Carpenter's Daughter - Vikkie Lee

5 жыл бұрын

In this video, I show you how I fit a monobloc Vapsint mixer tap for my kitchen sink and install the grey water waste pipe and trap.
Also, if you love what I do, please could you be so kind to vote for me to win one (or two) blogging awards? 😀
I'm under:
Section 4 - Tastefully Vikkie &
Section 11 - The Carpenter's Daughter
Here's the vote form and I'd MUCH appreciate your help again: bit.ly/34FzySS
Thanks so much x
VIDEO LINKS:
Speedfit plumbing video: • Utility Kitchen Part 2...
Cutting hole for sink: • Cutting Laminate Workt...
Plumber Parts Kitchen Sink Waste I followed *NOTE I HAVE SINCE ADDED A GASKET UNDER MY SINK DRAINER: • KITCHEN SINK WASTE - H...
Things I Used
As an Amazon Associate, I earn from qualifying purchases made through links.
Vapsint monobloc mixer tap: geni.us/thXCSUy [Amazon]
Speedfit Monobloc M10 15mm (*Depends on your tap): geni.us/LTQrs [Amazon]
Mcalpine Sink Trap with Washing Machine: geni.us/rrqw [Amazon]
Pushfit 40mm elbow: geni.us/OrFGwf [Amazon]
40mm pipe clips: geni.us/inGZ [Amazon]
---------------------------------------------------------------
You can also find me at the following places
🛒Shop in my Etsy Store: www.etsy.com/shop/CarpentersD...
Support Me Via Patreon:
/ thecarpentersdaughter
The Carpenter's Daughter Blog:
www.thecarpentersdaughter.co.uk/
Instagram:
/ thecarpenters_daughter
My Facebook Page:
/ carpenters-daughter-15...
Pinterest: / carpenterslass
Twitter: / carpenterslass
---------------------------------------------------------------
FOOD:
My Food Channel:
/ tastefullyvikkie
My Food Blog:
www.tastefullyvikkie.com
My Food Facebook Page:
/ tastefullyvikkie
Instagram:
/ tastefullyvikkie
Pinterest:
/ tastefullyvik
Twitter:
/ tastefullyvikki
---------------------------------------------------------------

Пікірлер: 127

@TheCarpentersDaughterUK 3 жыл бұрын

Here's my written guide if it helps: thecarpentersdaughter.co.uk/renovations/plumbing-tap-sink-waste/

@eleftheria1463 3 жыл бұрын

I need to do this in my own house and it is refreshing to see someone relatable making content like this! Thank you 😊

@michaellovell1368 2 жыл бұрын

Isn't it a GREAT feeling when all of your efforts actually WORK ?? This brought back memories of my own plumbing efforts in years gone by. Wish I'd have had the plastic fittings that are so readily available these days...but you still have to work everything out and then fit it all together. This video will be invaluable to the first timers...and even those who have already attempted other plumbing projects before.

@beesknees508 2 жыл бұрын

Fantastic! To see the joy in your face at the end '' I did this '' :) Yes you did. An excellent job! Fair play. :) A great video -thank you

@robzaphy 4 жыл бұрын

I’ve worked with both copper and plastic. I prefer copper but each to their own. You Did a great job.

@DannyT1503 3 жыл бұрын

Really great helpful videos. One tip you need to leave a gap of 60mm from your valves etc to your pipe clips to allow for expansion. That’s right out of the handbook from JG speedfit. If it’s to close the expansion could push against the pipe clip and the seal will fail. Hope that helps for the future 👍🏻

@Roof 5 жыл бұрын

Wow really like your channel! I’ve been doing bit of DYI and I’ve found your videos really helpfully! Thanks for uploading!

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks! :) And any time ;)

@garydouglass9577 5 жыл бұрын

I really like what I see! Cool job 🎄🎄🎄👏👏

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks Gary :) Glad I challenged myself on this now :)

@user-pn3xc1rg3g 5 жыл бұрын

Small pieces of 15mm copper pipe used as spacers is a neat and clean way to bring the pipes away from the wall. That's the best method I've found. Although maybe the hep will work the same way, as it will be hollow and rigid enough to take a screw. Great work as always 🙃

@TheCarpentersDaughterUK 5 жыл бұрын

Yes, I was hoping it would be the same with plastic plumbing :) Thanks for the tip :)

@EuroB0B1 5 жыл бұрын

Yeah hind sight being the great thing it is, services to and from sink needed a little more planning but hey i say this as spark and you have done more plumbing than i ever have. Also fitting out the sink furniture before fixing in absolute genius, if you dont mind i wil borrow that one day! As always great vid and great to see you gettin stuck in.

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks and feel free to use that idea haha. Planning is definitely not my favourite part of DIY, but I'm definitely getting a bit better than I used to be lol. It'll be great to look back on this if I ever need it :)

@jonsmith8582 5 жыл бұрын

Spot on with the idea of fitting some wood packers for the pipe clips , a dab of no-nails will hold them in place , wait till the no-nails has set and then fit the clips , top video as usual

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks for the tips :) Will definitely use some wood now as it sounds the strongest option :)

@carolesmith9093 3 жыл бұрын

You solved a problem for me as regards the sink bit. Thank you

@David-ve9zm 5 жыл бұрын

Really enjoyed watching this series of videos. What I have really taken on board from you is that it is worth taking your time and breaking the project down into smaller manageable tasks which makes it far less daunting. My late father-in-law used to say "measure twice & cut once". Looking forward to the next project.

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks! Breaking it down has been much easier for me to digest too.. and a few deep breaths 😄

@ranjankc121 5 жыл бұрын

Brilliantly done.. voted for you...

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks again so much :)

@logcoatingservices 5 жыл бұрын

I like the easy fix, plastic fittings - very cool

@TheCarpentersDaughterUK 5 жыл бұрын

Me too!!!! I suppose any pushfit I feel dubious about, but the seal inside seems to do the trick 😊

@MakingItOutOfTheWoods 5 жыл бұрын

So much to do - you did an awesome job 👏👏👏🌲🦊🌲🤩

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks, Claire 😍 And totally worth it!!

@I_Am_Michael 5 жыл бұрын

good job with the routing and slowly fitting the connections. wood scraps can make it easier to bring the supports to the pipes for support. and if you paint happy faces on the scrap blocks they do a better job supporting things. flexible pipes and connections with rubber or silicone seals are so much easier than the old way with rigid pipes and glue. great job. already voted for you. now for the ultimate question. is this all Hans approved? I am sure it is. HA!

@TheCarpentersDaughterUK 5 жыл бұрын

LOL to the happy faces 😂 And thanks so much again 😀👍

@jonathangrosvenor2917 5 жыл бұрын

Nice job - I fitted my sink last year too. My only ‘tip’ would be to silicone under the sink basin, I.e where the sink meets worktop. That way, no water or cleaning product will seep under the basin and damage the worktop or cupboard. Keep up the good vids!

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks! That's exactly what I'll be doing next and clipping the sink in to place :)

@gort5583 5 жыл бұрын

Great to see well done.

@TheCarpentersDaughterUK 5 жыл бұрын

Thank you 😁

@stephentamlyn6633 2 жыл бұрын

Amazing

@SCRAPWOODTOCRAFTWOOD 5 жыл бұрын

Great video vikkie as always

@TheCarpentersDaughterUK 5 жыл бұрын

Thank you Warren :) Always worth challenging yourself! You just never know what you can achieve :D

@SCRAPWOODTOCRAFTWOOD 5 жыл бұрын

@@TheCarpentersDaughterUK like they say the world is your lobster 😂😂

@kanecree4570 5 жыл бұрын

for the waste pipe clips i usually cut two small little bits of 15mm copper (or smaller) at about 1cm long or size required and use some longer screws. this steps the clip off the wall that little bit that is required.

@TheCarpentersDaughterUK 5 жыл бұрын

Thank you so much! :)

@theenforcer9965 4 жыл бұрын

found it love them taps

@paulr8898 5 жыл бұрын

Looks good it came out well. As other people have said silicone around the wast where the two metal parts meet in the bowl. And longer screws with the pipe clips and off cuts of 15mm pipe. But nice job.

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks so much! :)

@TheCarpentersDaughterUK 5 жыл бұрын

Update, I've now found a spare gasket from sink waste that came with another sink, so the drain is now sorted! Thanks for bringing this to my attention!

@LevBulgarski 5 жыл бұрын

Hats down!

@mpgrewal00 3 жыл бұрын

You make it look so smooth and clean but in reality....

@terryrobinson3016 3 жыл бұрын

I love how honest your videos are and really informative. I'm just wondering have you had any leaks with the jg speedfit fittings as I'm thinking of fitting a shower using them. 👍

@TheCarpentersDaughterUK 3 жыл бұрын

Thanks :) I've never had a leak from my own Speedfit plumbing, but ive had to repair one my father in law installed under our toilet sink. I found it's far better to replace a £2 piece from scratch and throw the old one away. The leak was very slight, but I'm a worrier 😂

@terryrobinson3016 3 жыл бұрын

@@TheCarpentersDaughterUK Great thanks for getting back to me. You have my vote. 😁

@mattwright1726 5 жыл бұрын

Great vid, great channel

@TheCarpentersDaughterUK 5 жыл бұрын

Thank you so much! 😊

@Mikidy303 5 жыл бұрын

Good Job! Code won't allow me to use any flexible pipe for waste water in my region, but I like what you've done. And you got my vote again. Recently was assigned a new IP by my ISP. I can't think of a better way to use it.

@TheCarpentersDaughterUK 5 жыл бұрын

Haha, thank you so much again! :) I wonder why you can't use flexible pipe? 🤔

@Mikidy303 5 жыл бұрын

The major problem with them is that they collect the dirt and grime that’s supposed to flow down the drain. The zigzag sides are great for slowing down the flow of water and letting the gunk sit and collect. Making matters worse, since they slow down the flow of water, gunk can easily collect further down the pipe, especially if they pipe already isn’t 100% clear.

@MsPdog1 5 жыл бұрын

Cool!

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks so much :D

@jhmsmarttv795 5 жыл бұрын

Lovely video Vikkie! Don't mind the five clowns who just had to downvote the video. They did that just because they are jealous of this hot DIY:er. 😘

@TheCarpentersDaughterUK 5 жыл бұрын

Haha, thanks so much! Great use of the word clowns too 🤣🤣

@kevpatchett5680 5 жыл бұрын

Longer screws then cut some small pieces of 15mm pipe the same length as the gap from the clip to the wall these will act as spacers and you will be able to tighten the clip up nice and snug. I do this all the time it’s a lot neater and tidier than using a piece of wood.

@TheCarpentersDaughterUK 5 жыл бұрын

Thank you! :)

@kevpatchett5680 5 жыл бұрын

You are more than welcome ☺️

@anthony342 5 жыл бұрын

thats what i do , im a plumber

@kevpatchett5680 5 жыл бұрын

I am also a plumber 😃

@ewanbaxter9199 4 жыл бұрын

Of course before you connect (Your washing machine outlet) to the spigot you have to cut the sealed end off the spigot to the diameter of your hose.

@srasul8 Жыл бұрын

Thank you so much for this. Life saver can you use a bottle trap instead of P trap. Which is best?

@TheCarpentersDaughterUK Жыл бұрын

I've used bottle traps when I need save space. I've read since a p trap has better flow, but I'm not a plumber - it's just something I read.

@normanboyes4983 5 жыл бұрын

Did I miss you siliconing the sink to the worktop? Have you got an effective anti. - siphon loop for the dishwasher drain?

@philmccole2634 5 жыл бұрын

Nice job hun

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks so much :)

@KdeB 9 ай бұрын

If there is gurgling after your tap water goes down, consider replacing the McAlpine with a built in Vented McAlpine, it happened to me so was an easy fix.

@daz3660 5 жыл бұрын

to tighten the waste to the sink you could always use an old chisel or flatten the end of a offcut of 15mm copper pipe x

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks so much" Prefer the idea of a chisel compared to a smaller flat head screwdriver :)

@ericcorse 5 жыл бұрын

Well done, Its kind of fun like a puzzle, assuming you don't have to go the store 53 times.

@TheCarpentersDaughterUK 5 жыл бұрын

Yes, it was 😁 I look back and it was relatively simple, but some head scratching when you're learning the ropes 😊

@BossmanEight 5 жыл бұрын

Using blocks to shim out pipe supports is perfectly normal around here. Try to hit wall studs when you're securing the blocks. If you can't do that then make sure to use proper drywall/sheetrock/plaster anchors. (I have no idea what they're called in England.)

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks so much :) I think they're just called plasterboard fittings around here, but know what you mean ;)

@Bazza1973ify 5 жыл бұрын

Damnit Vickie, when you said "you know you want to" I spat my cuppa out...... You never say that to me 😈😈😈

@TheCarpentersDaughterUK 5 жыл бұрын

🤣🤣🤣🤣 you can't make it up 😂😂

@plumber13946 4 жыл бұрын

Use bits of flexi pipe as spacers for the waste pipe clips.

@sbajwa2480 3 жыл бұрын

Good work beautiful lady . One problem my eyes watching you more, rather than what you doing. you are gorgeous. Blessings.

@ilookafterthewater601 5 жыл бұрын

Another cracking good job seriously well jobbed, then :o) And I'm a tad dubious about the voting thing! I get this message: "Thank you! Your vote has been registered!" But the heart never seems to be filled in red; it just has a red outline. Is anybody else experiencing this??

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks, I thought the same too to be honest lol. You could try this link instead bit.ly/2S2XFE6

@MQureshi1 3 жыл бұрын

what is the size used for pipes for kitchen sink waste? 30mm or 40mm?

@TheGreg2710 3 жыл бұрын

40mm

@jimmyman8031 5 жыл бұрын

Why not clip to the wall but use bits of 15mm pipe as spacers between the clip and the wall? That’s what I’d normally do. Neat job by the way.

@TheCarpentersDaughterUK 5 жыл бұрын

Thank you:) And thanks for the tip :)

@Autonomous1969 Жыл бұрын

The problem I had is that some sellers say 1.5" is 38mm and some say it's 40mm.

@TheCarpentersDaughterUK Жыл бұрын

I spotted the same problem in Wickes last year when I needed to get a very specific waste pipe.

@TheCarpentersDaughterUK Жыл бұрын

Ended up having to use a reducer

@jonyG1991 3 жыл бұрын

16 sad people giving her a thumbs down ..no need for it

@amcluesent 5 жыл бұрын

Probably a personal choice, but a telescopic unit would be an option to adjust height of P-trap to get the correct degree of fall for the waste pipe - www.wickes.co.uk/FloPlast-TW473-Telescopic-Appliance-Half-Trap---40mm/p/431942

@TheCarpentersDaughterUK 5 жыл бұрын

Ahhh! That's a great idea! Thanks! :)

@DasArab 5 жыл бұрын

Yea scrap wood behind, or just put the clip on to the pipes and use longer screws and dont tighten them hard against the wall.

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks!! I wondered about longer screws, but with it being plasterboard, I think the first method will be better 😊

@phildxyz 5 жыл бұрын

Good work, but I'm afraid I'm old fashioned and use copper everywhere I can in my house - except waste of course...

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks so much! One day I'd love to give it a try with copper! I think plastic is particularly great for learners like me 😁

@actiongirl5 5 жыл бұрын

I think both have it's place in the world of plumbing. I prefer copper but when you do not have tools or the ability to work with copper pipe then as long as you use the plastic pipe properly and for the right use I do not necessarily think it's the worse thing ever invented and I can really see the pros.

@phildxyz 5 жыл бұрын

@@actiongirl5 I'm sure you are right - just all those push in rubber seals make me a bit nervous :)

@actiongirl5 5 жыл бұрын

@phildxyz Obtaining quality made and tested plastic pipes, end caps, valves, etc will at least minimise faults or leaks. I'm with you on the old copper, nothing says reliability like shiny freshly soldered copper pipes..... ;D

@fro0tyl0opy87 5 жыл бұрын

Copper all the way for me and looks beautiful when buffed up

@fireblaster9961 4 жыл бұрын

Hold tight

@nikereebokpuma3406 Жыл бұрын

Your beautiful 💞

@GD-qu9hr 5 жыл бұрын

With the waste pipe I'd use some spare bits of 15mm copper to make spacers so the clips stand off the wall

@TheCarpentersDaughterUK 5 жыл бұрын

Thank you so much! :)

@11982463 5 жыл бұрын

need plumbers mate or silicone

@jamiefors5062 5 жыл бұрын

You really need to put the hose crook around that washing machine hose, water could siphon back into the machine the way you have it. Fair play for doing it yourself 👍

@RahimRahim-cc7rl 3 жыл бұрын

like like

@paulyh4531 5 жыл бұрын

Yer just get some Packers of wood the fix the clips to that there's no real wieght there anyway . 👍

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks so much for the tips again :)

@imransheth4171 5 жыл бұрын

Can u fit my tap?

@TheCarpentersDaughterUK 5 жыл бұрын

:D It might be a VERY long time til I get round to it lol... I've agreed to do SO much around my house 😂

@DaveJudd 5 жыл бұрын

You forgot to seal the drain, it might leak with plug in.

@TheCarpentersDaughterUK 5 жыл бұрын

At what time? There's a seal underneath the drain with that plastic bit.

@DaveJudd 5 жыл бұрын

Plumbers mate or silicone around the waste has you set it in sink.

@TheCarpentersDaughterUK 5 жыл бұрын

Just to give you an update - I've now found a spare gasket from sink waste that came with another new sink we had (although the actual sink got damaged in transit), so the drain is now sorted :) Thanks again for bringing this to my attention!

@DaveJudd 5 жыл бұрын

Most plumbers use silicone or putty because the foam gasket fails and you get callbacks.

@actiongirl5 5 жыл бұрын

We had our kitchen sink fitted by a fitter installed the kitchen and he did a similar thing, no silicone no nothing just the gasket the sink started to leak into the cabinet below and the same went for the overflow as the rubber seals just do not seem enough on their own and this was a Franke sink. I would highly recommend silicone for the seal. I did that with ours and 6 years on not a drip!

@andrewdavies1312 5 жыл бұрын

First?

@TheCarpentersDaughterUK 5 жыл бұрын

Yes.... YOU WIN!!!!!!! 😂😂

@andrewdavies1312 5 жыл бұрын

My first 'first' comment ever. Not gonna lie....feels good haha

@TheCarpentersDaughterUK 5 жыл бұрын

😂😂

@TheCarpentersDaughterUK 4 жыл бұрын

Hi all, if you love what I do, please could you be so kind to vote for me to win one (or two) blogging awards? 😀 I'm under: Section 4 - Tastefully Vikkie & Section 11 - The Carpenter's Daughter Here's the vote form and I'd MUCH appreciate your help again: bit.ly/34FzySS Thanks so much x

@regmccormack3157 5 жыл бұрын

It is great to see a chick doing a trade and are you qualified?.

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks! No, just learning as I go along each week for my own house renovations. I won't touch electrics or gas though.

@nachtdiertje1972 5 жыл бұрын

It will work, but no craftmanship is shown. Work straight and plumb en fasten the pipe, not the couplings. Look into regulations and then start a YT-movie. Also 1 cm/40 cm is much too much. Your drain will fall dry and clogging will appear. 1cm/100cm is much better. Also the whole rerouting with the water is strange and takes too much material.

@TheCarpentersDaughterUK 5 жыл бұрын

Thanks for the feedback. I'd like to clarify that I haven't said I'm a craftsman. Nor is this a tutorial.