Very nice informative video, thanks ! I'll be following forsure!
@rodzillamotorhead4262 жыл бұрын
Could you please add in the timing chain guide installation to this video? I too had to pull my flywheel back off and clean off the retaining compound to get the guides in place. It's a MAJOR hassle and is the only glitch in this otherwise very helpful video series.
@troymcdonald90862 жыл бұрын
Yea Thats Kind of a Big Skip i Noticed when he was putting the head on ! I was like Where did the guides come from did i miss somthing Nope just forgot that part!
@troymcdonald90862 жыл бұрын
Even with that it is the Best Rebuild video that ive found it Helped me rebuild my 16rzr 1065 HL !
@user-er6xo5nt5r11 ай бұрын
(2016 RZR 1000xp HL) Watched video a few times (assembly) also have the tech manual, bought a disassembled engine(exhaust valve broke off and did some damage), got the short block together and noted the jet piston (piston oiler) not installed. This is not listed in Tech manual nor video, talked to my local service tech and they didn't find it either. He commented nothing unusual for Polaris to not list everything. Get to pull apart and figure out where oiler goes?!?! Had to order new Oiler since one of the tubes was bent. Otherwise a good informational video.
@irfanrasool1098 Жыл бұрын
Thanks, dude your video very helpful
@rawbdiggity Жыл бұрын
Just got my xpt motor back together today. Thanks Charles great vids.
@zackbrown6555 Жыл бұрын
How is this hot rod rebuild kit holding up? Anyone else use this kit and would you recommend it.
@primitivomendozamata664310 ай бұрын
It's fine good
@joshuacarr60492 жыл бұрын
Is it absolutely necessary to use the cam shaft timing plate when timing ? Didn’t put my stuff TDC when disassembling and having trouble getting the timing right.
@NO-background-music-in-videos.2 жыл бұрын
Excellent..
@stitches489710 ай бұрын
Hey Charles I’m just getting my engine finished up from a rebuild I’ve got a 2020 xp1000 with the automatic style tensioner that bolts to the cylinder housing. Is it normal for the front 2 intake valves to be slightly open when setting the timing on the engine ? I had to move the intake cam so that it would open the valves slightly just to get the camshaft timing plate on. I tried taking the buckets off to see if it was shims size but the cam lobe was hitting the spring. So what I did was torque the caps, set the timing plate on the rear then install the sprockets and chain. After that I installed the tensioner to hold everything together and made sure it was fully seated by slightly moving the cams to get the tensioner to ratchet outward. After doing this the engine seemed to be perfectly in time but the front 2 intake valves stay slightly open at Tdc is this correct? Thanks again!
@MrRoush3602 жыл бұрын
Is it possible to get the pistons, the piston sleeve, back into the top end with out taking the engine complete apart?
@rmatvmc2 жыл бұрын
With one piston high enough, the other would be too low. I would plan on a full disassembly to make sure the rings aren't damaged on assembly. -Charles
@jacobecavalier14992 жыл бұрын
Yes it’s possible
@sphen4176 Жыл бұрын
Isn't TDC on the flywheel a + mark?
@danielmaehren882 Жыл бұрын
No just a straight line.
@troymcdonald90862 жыл бұрын
Ypu sure skipped over a big step like attaching the connecting rods?
@joshh21712 жыл бұрын
I have been following this video series to a T... this one you guys totally skipped over the installation of the chain guides. I had to pull my flywheel back off, use the puller even (since the compound had set up). 😞
@joshgay94633 жыл бұрын
What year and model was this?
@germanlopez47962 жыл бұрын
So about the crank seal on the clutch side of the motor I notice it has a flange if I was able to remove that with flange and all without damaging the engine case can I install a conventional seal without a flange and have no issue with leaks???
@troymcdonald90862 жыл бұрын
It will blow out thats why the flange is there . To much crankcas pressure?
@nestoralanindagarcia65012 жыл бұрын
👏👏👏 maestro
@JoshuaReed-e9oАй бұрын
What did you figure out on this? I'm in the same situation right now.
@oscarparedes22963 жыл бұрын
Tengo un problema me puden agudar x favor
@oscarparedes22963 жыл бұрын
Es muy importate gasteste 2000 dolares de mi bosa algien aguedeme x fava