Porsche 917k from Fujimi the Le Mans 1971 winner 🏁 full build 1/24 🚀

Рет қаралды 21,176

Жыл бұрын

#adhoccars #fujimi #Porsche #modelkit #lemans
Hello! It’s been a long journey to finish another Porsche model kit but finally It’s over and I am able to present you Porsche 917K from Fujimi the winner at the Le mans in 1971. The Car itself is the 70's legendary racing car developed as Porsche 908 was not able to surpass the Ford GT40. It is equipped with 4,5l horizontal V12 cylinder engine and it has a specially-built lighter magnesium tube-frame chassis, whereas all the other 917Ks had an aluminium one. If it comes to the body the car has vertical fins and two air boxes on the tail section for better aerodynamics and cooling. As a result, the 'finned' 917Ks were faster than the 1970 versions and Porsche became the champion at the international manufacturers championship. K stands for Kurzheck which means a short tail. Which was evolved at the racetrack with gaffer tape and aluminium sheet as the initial 917s aerodynamics made it nearly undriveable at higher speeds BTW The long tail version had a maximum measured top speed of 386 km/h (240 mph). Ok so now about the modelkit, honestly, It was the worst model that I have ever build. I know that I haven’t made them a lot but number of crooked parts or the ones which just didn’t fit were huge. Experienced modeller for sure would have done it much much better but torn decals and the front hatch looking like tank hatch… This kit just went wrong :D Nevertheless I didn’t throw it to the bin and decide to make a video out of my not so good work. I wouldn’t recommend this kit to beginners but everyone who would like to find the limits of patience feel free to buy it :D Is there any model kit which challenged you so much that you wanted to throw it out? Share your story in a comment, enjoy the video! Thanks a lot for every like given, cheers!!
Recording just for entertaining purposes, there might be as many ideas for doing it as number of all diecast in whole world :D
I am a beginner but I am not afraid of mistakes :)
If you enjoy the video you can like it, subscribe the channel, leave a comment or even donate via Paypal.
Each option above is warm welcomed!
Thanks for any support given!
If you like it please subscribe, more cars and DIY are up to come!
If you enjoy this content, feel free to buy me a coffee to help keep me fueled while I spend nights creating it. THANK YOU :D
www.buymeacoffee.com/adhoccars9D
Instagram / adhoccars
Fujimi Porsche 917k 71 Le Mans Winner 126142 RS-88
Primers:
Mr.Hobby Surfacer 1500 Grey
Mr.Hobby Surfacer 1500 White
Thinners:
Mr. Hobby Leveling Thinner 400
Tamiya X-20A
Paints
Tamiya
X-18
XF-10
X-11
X-1
XF-1
XF-63
X-7
X-2
XF-2
X-26
X-27
Mr. Color 44
Clear coat:
GX112 SUPER CLEAR Ⅲ UV CUT GLOSS
Panel lining:
Tamiya Panel Line Accent Color Black
Decals:
Microscale Micro Set
Microscale Micro Sol
Wax:
Soft 99 Fusso Coat Black
Assembly:
Microscale Micro Kristal Klear
Tamiya 87038 Extra-Thin Cement
Polishing:
Tamiya Masking Tape 18 mm, 3 mm, 1 mm
Tamiya 87069 Polishing compound - Fine
Tamiya 87070 Polishing compound - Finish
Tamiya 87192 Polishing Compound Sponges
Tamiya 87090 Compound Applicator
Tamiya 87192 Polishing Compound Sponges
Tools:
Airbrush MIG AMMO AirCobra 0.3,
Tamiya 74522 Spray-work painting stand set
Sanding paper, files, sponges: 600/1000/3000/4000
Drills: 0,8 mm and 1.5 mm
Sharpie Black Permanent Marker
Tamiya 74052 Decal Tweezers
OLFA KB-5 knife
Italeri 1 mm Paintbrush
UHU Patafix white, removable adhesive pads
Microfiber cloth
Other tweezers and pliers from DIY store
Cotton buds and toothpicks
Intro:
Intro/Outro/Banner Creator : Admj707
KZfaq Channel : / admj707
Picture: Free vector from: vectorportal.com
Music: Dude - Patrick Patrikios
Font: Porsha Condensed from www.dafont.com
Adjustment: Adhoc cars

Пікірлер: 54

@Ovenmitttt Жыл бұрын

I love your comments. I laughed so hard I lost my coffee. Great work on the car!

@AdHocCars Жыл бұрын

Thanks!! Glad you had nice time watching this video! 😀

@jeangratton1085 Жыл бұрын

I have heard that this was a difficult kit to build but you showing us the warped areas now prepares me better for my build. All of a sudden it doesn't seem that scary anymore. The 917K is a beautiful car that I want to add to my collection and now I think I can. Thank you so much for this video.

@AdHocCars Жыл бұрын

Hi Jean. Thanks for your feedback I am glad that you have found my content valuable :) As far as I recall there were couple of more issues to challange like side windows (they didn't fit either due to their shape or warped body), martini stripes decals on the front fenders (I wasn't able to achieve the right curve even with decal softeners so I needed to cut them a bit on one side to get the right curve and then fit the stripes alignment), top hinges of the rear body (they are really thin so it is quite easy to bent them while checking the body alignment), front hatch (it is just too big compering to the real one, needed additional work). I have seen couple of great projects regarding this modelkit which were done with a lot of care for details and now I know how much effort was put to made this model look great. The 917 itself is a real beauty! :) wish you good luck with your 917 😀

@jeangratton1085 Жыл бұрын

@@AdHocCars Thanks for the follow-up. I think I'll print your comment and place it in the box until I start the build

@AdHocCars Жыл бұрын

You are very welcome! :)

@blackthorne1497 Жыл бұрын

Great Job. You have restored my faith in my ability to build a crappy Fujimi model kit. My last one was a disaster movie. I see that with some patience and time you can actually have a beautiful result. Thanks for sharing this video...I will give it a try.

@AdHocCars Жыл бұрын

Thanks for taking the time to watch and comment on my video! 😁 I'm glad that this project inspired you to give the Fujimi model kit another try 😀 full agree that these kits can be difficult and crappy...I struggled to achieve the desired level of quality with this particular project but It is fine... However, I strongly believe that patience is key when it comes to model building, and with enough time and effort. I wish you the best of luck with your kit! Thank you again for your feedback!😁 are you going to build another 917? 😀

@marcus7947447 Жыл бұрын

Great job. Can't wait for more.

@AdHocCars Жыл бұрын

Thanks for positive feedback😁 I hope that next projects will be at least a bit easier! 😀

@Jeff-cv4qn Жыл бұрын

Beautiful build!

@AdHocCars Жыл бұрын

Thank you for your feedback! really appreciate! :)

@SketoThanos Жыл бұрын

Beautiful car. One of my favorite!

@AdHocCars Жыл бұрын

thanks for your supporting comment! 🙃 i hope next project will be much better!😄

@michaelcooke2559 Жыл бұрын

Nice build. Very clean. Thanks for sharing.

@AdHocCars Жыл бұрын

Thanks Micheal! :) my pleasure!

@michaelhintzmikesminiature1812 Жыл бұрын

Awesome Video!!! Awesome Build!!!! Thanks for sharing

@AdHocCars Жыл бұрын

Thanks Michael for your positive feedback! 😀 I will do my best to make a next project even better! 😃

@ExorcisteDeMorteau Жыл бұрын

Excellent. Bravo.

@AdHocCars Жыл бұрын

Thank you!! 💪

@phone7491 10 ай бұрын

wow , just found your channel absoluty underrated video build for diecast. nice detailing man👍🏼

@AdHocCars 10 ай бұрын

Thanks for positive feedback! I think I won't get golden button for 1 milion subs but maybe I will reach 2k in a year or two 😂 your comment brought me feeling that my content is valueable and there are people who actually enjoy it! thanks!!😃

@ericverpeten8503 Жыл бұрын

Beautiful build! 👍👍👍👍

@AdHocCars Жыл бұрын

Thanks! glad you like it!!💪👍

@Deano084 6 ай бұрын

Looks fantastic! Great looking model.

@AdHocCars 6 ай бұрын

thanks!! there are couple of issues here and there but overall it looks quite nice!!

@inzMaraz Жыл бұрын

Good job 👍

@AdHocCars Жыл бұрын

Thanks a lot for positive feedback! :)

@keithsmodelsandrcs6593 Жыл бұрын

I've fujimis other silver martini one these awsome job browell done

@AdHocCars Жыл бұрын

I hope yours is better quality then mine as I have had some challenges with this white one 917!

@jayblair3207 10 ай бұрын

I pulled mine out of the stash to have a go with it. Your video will be playing along as I build it. Hopefully I can do the same justice you did to yours. I did toss the fist edition Kinetic 1/48 F-16 Sufa. That was a disaster

@AdHocCars 10 ай бұрын

Thank you! I'm really happy that you find this video valuable😀. However, this kit brought unexpected challenges, and due to a combination of its relatively lower quality and my limited experience, it didn't bring me much joy. I hope that in your situation, things will be different, and you'll overcome every challenge effortlessly! so Kinetic adventure won't happen again 😀

@NitroModelsAndComics Жыл бұрын

I passed on that kit a number of times. I may have to get one. Nice build BTW...

@AdHocCars Жыл бұрын

There are couple of more 917k kits from fujimi maybe others are less challanging 😃 Gulf one looks nice :) Thanks! I did my best! :D

@rolandpauscher2707 5 ай бұрын

There is a Firestone decal on the car but Good Year's are mounted....🤔

@AdHocCars 5 ай бұрын

True! There are two types of decals to choose from. Firestone and Good Year. I chose Good Year, there should be also AVON available as there is a 917k #22 in Stuttgart museum with this tires on :) but it isn't...

@ungurdani8346 3 ай бұрын

Salut my friend super car super video subscribe subscribe . ..

@AdHocCars 3 ай бұрын

Salut! thanks a lot!!

@markc7002 9 ай бұрын

Excellent result from such an uncooperative kit!!

@AdHocCars 9 ай бұрын

thanks!! it was a tough one indeed, I could build this kit better this time as I have some more experience today :D

@jakubmaecki1340 Жыл бұрын

Good job even if it was not so easy to build.

@AdHocCars Жыл бұрын

Thanks a lot! that was a quite difficult kit with a lot of challenges... fortunatly my next project Porsche 959 from Tamiya goes quite well! 😀

@jimmccormick6091 8 ай бұрын

for those in the know, was this the old UNION kit from Japan? (Which may or may not have been a HELLER kit at one point)

@AdHocCars 8 ай бұрын

That's interesting! I just watched a review of the UNION kit, and the sprues look a bit different. I would answer that these kits are different, but I haven't built either the Heller or Union kit. Are they as low in quality as this Fujimi kit? :)

@OnnoWeeda 9 ай бұрын

What a great build,despite the issues you had. I love the model and will keep your video as reference. May I ask how many layers varnish you used?

@AdHocCars 9 ай бұрын

Thanks a lot for feedback! sure, basically it is 3 - 4 ml of varnish in ratio 1:4 and 1:6 (clear coat : thinner). Every layer has min 5 minutes dry time and there are about 4 or 5 thin layers.

@OnnoWeeda 9 ай бұрын

@@AdHocCars Thanks, doesn't it get to thin? Thin like water?

@AdHocCars 9 ай бұрын

It gets really thin and it is quite easy to overspray. I am using AirCobra 0.3 airbrush with the smallest spot setting to avoid these kind of issues

@OnnoWeeda 9 ай бұрын

@@AdHocCars Thanks for your answer. I am stepping over from spraycans to the airbrush. It gives more control with the airbrush. So just asking around what other modellers are doing 👍🏻 Helps me a lot.

@AdHocCars 8 ай бұрын

You are welcome! I think that everyone has its own way of doing things, your research will help to find yours for sure! :)