Sir yes it can be done , but battery needs to be disconnected for at least 15-20 mins , because almost all modules have capacitors and they can store a little bit of energy for some time , so we need to wait until those caps are drained

@@yourDIYneeds thanks

Perfectly fine

Sir was the alignment done in the right manner ?

Yes, I took it to 3D alignment

Can you tell me the exact code you are getting sir ? Because i want to know , whether the angle sensor is reading wrong angle or it's not working .

P160900 B201000 U042800 Here are the codes

Sir 5w40

@@yourDIYneeds castrol or shell?

Sir shell

Sir OBDeleven device and their app

Sir have a look at this video - kzfaq.info/get/bejne/jpOjgZydv8mbqWw.html

Hanji sir bilkul

@@yourDIYneeds thanks bro bhai... You tube pai bus apke he channel pai reply aata hai.thanks bro keep it up

Sir , it won't get successful

First is to make sure that the steering module is getting proper voltage , Check continuity for grounds , as half of communication faults are just because of drop in voltage . And check the electrical connector of the steering module for any corrosion buildup

@@yourDIYneeds i have checked the wires expect on the steering house because it is hard to get there. Is the module at this type at the steering wheel?

Then try scanning the module and check the resistance and power voltage on the module from the diagnostic tool .

@@yourDIYneeds i wil try i have now autel my vcds it not working. And do you know where the module is?

Module no. 44 Go in live data and check the parameters

Sir , it will be safe but not that reliable

@@yourDIYneeds will something happen to the engine? I just want to get rid of the lag and improve driveability that's it, no high end remaps

It will improve driveability, can't say anything about the lag , because it depends upon engine to engine

Sir , can you tell me which vehicle you exactly have , because a lot of vehicles may require you to code the new battery as per the specs of the new battery , so that the alternator can adjust itself for charging

@@yourDIYneeds Thanks for the reply. It’s a 2012 1.6 TDI Vento. Does PQ25 platform require battery coding like MQB?

No sir, PQ series of BCMs doesn't require battery adaptation, alternator has a specific part called " voltage regulators" which can go bad , but that doesn't make the voltage reading "000" , it will start to throw out either massive amounts of voltage or no voltage at all . If there is no issues with the engine cranking , and alternator is doing its job of charging the battery and powering the electronics , then it can't be alternator . What i feel like is , its more of a fault with the voltage reading circuit of the BCM itself , because at the end of the day , both ECM and BCM are nothing but just very advance Multimeter which has the capabilities to send and receive signals multiple times per second . If voltage is low then it will throw a code but that's not the situation here i guess. So either the transmission end of the stream is bad or the receiver end , in both of the case we will get the same code . Hope i made a valid point to understand .

@@yourDIYneeds Thank you so much for the input. I’ll test it out and let you know of the results.

@@yourDIYneeds Hi, I took out the negative terminal off the battery for about 5 mins and put it back on. Cleared the error code and it didn’t come back. Thanks a lot. One more query. Is it bad for Camshaft position sensor to be higher than 4.8 degrees? I got timing belt replaced earlier and still the values sits at 5.25 in warm conditions. Could it be a bad sensor or timing needs to be rechecked?

Sir , screen replacement can be done but finding the right screen will be a task

Sir you check their official website and check for price and do let me know the price , because i have a person who is into these things , then afterwards i ll confirm from him , whichever will be less expensive , you can buy from that source

Yes sir approvals are formed on the basis of presence of specific additives, they make a lot of difference in longevity of the engine

Sir i gave it to my cousin, as we can not drive any diesel vehicles which are 10 yrs old in national capital

@@yourDIYneeds OK bro,, but missing d beast,, u know what it feels 🙌

Yes sir

Have you checked glow plugs ?

@@yourDIYneeds no I have not check but is that only the issues or other one because after the engine start car not automatically off but when we off the engine and then trry to start it's not starting and after same time it's started so glow plugs is the issues????

Sir had car ever ran without fuel , air got into the fuel system ?

@@yourDIYneeds yes... Not run but trying to start

Sir may have to check the pressure of high pressure fuel pump

Sir they are available in obdeleven platform and if they are not then you can search for it

Sir i was basically testing voltage and continuity In continuity polarity doesn't matter In Voltage it does but it shows reading in -ve And i was sure that alternator is producing power not drawing it 😅😅

Yes , voltage issues can create the issue

Obdeleven

Sir i am doing good , hope you are also doing well, you can contact me on my mail everydaydiyhelp@gmail.com

Sir gave it to my cousin , as it was 10 yrs old now and we can't drive a vehicle which is 10 yrs old in national capital

@@yourDIYneeds hope you meet your cousin soon and make some videos❤.. Your safari's videos were stress-buster😅

😂

Sir if you are using Android then its for €40 If apple then €60

Yes procedure is exactly the same

@@yourDIYneeds thanks boss, I'll go try now. I have same issues. Red steering. But sometimes its fine... Sometimes it makes this problem.

Unfortunately on my golf that did not resolve the issue. The red steering light still comes up

Tried disconnecting the cluster ?

@@yourDIYneeds yes... I disconnected the cluster.... And connect it back after 5 minutes. Didn't work, now left it disconnected and batteries are disconnected too now .. i will connect it in the morning and see how. Is there other fix for this?