Powering a pi

  Рет қаралды 3,757

Matthew Lawrence

Matthew Lawrence

4 жыл бұрын

Powering a raspberry pi with a buck converter from a 24v battery
visit www.flightradar24.com to find out how to build a flight tracker yourself.

Пікірлер: 13
@brentjohnson6654
@brentjohnson6654 2 жыл бұрын
Good video. I think the volts for the pi a bit higher like 5.1-5.5? Do you get a low power warning on the pi desktop? Again, thanks for the video.
@dalesmith8666
@dalesmith8666 4 ай бұрын
what's the part number of the device? (on the chip)
@mmdirtyworkz
@mmdirtyworkz 3 жыл бұрын
Why not use micro USB connection for power, leaving GPIO pins free for other stuff?
@mathewlawrenceml
@mathewlawrenceml 3 жыл бұрын
You can do. I just did it this way because I had the parts to do it this way and for ease. As in this use case I have no need to use the GPIO.
@mmdirtyworkz
@mmdirtyworkz 3 жыл бұрын
@@mathewlawrenceml Oh I see. Just starting with the Pi so I watch as much videos/guides as I can. Awesome setup you got there!
@mathewlawrenceml
@mathewlawrenceml 3 жыл бұрын
@@mmdirtyworkz thank you. And good luck with your projects.
@khushsharma
@khushsharma 3 жыл бұрын
can we measure battery power % in raspberry pi if you use buck converter
@mathewlawrenceml
@mathewlawrenceml 3 жыл бұрын
You would need a external ADC as the pi has no analog inputs. But it could be done.
@khushsharma
@khushsharma 3 жыл бұрын
@@mathewlawrenceml I have ads1115 but my battery is 12volt and I use buck converter to get 5volt ,will ads1115 give me reading from buck converter directly
@mathewlawrenceml
@mathewlawrenceml 3 жыл бұрын
@@khushsharma no your need to use a resistor devider to bring the voltage down to a safe level. As feeding 12v into the ADC will damage it. Say for example you used a 24k resistor from the 12v to an input of the ADC and a 9.1k from the same input down to 0v that will give you a 3.3v I put for 12v battery level.
@khushsharma
@khushsharma 3 жыл бұрын
@@mathewlawrenceml no sir my question is ,I am getting 5v from buck converter which is connected to 12 volt battery. Can I measure battery level from that 5v( buck converter ) by ads
@mathewlawrenceml
@mathewlawrenceml 3 жыл бұрын
@@khushsharma not after the buck no. You'll have to take a sample from the input of the buck. Unless there buck chip has any Comms on it. But that would require looking for that chips datasheet ect.
@lunge1
@lunge1 2 жыл бұрын
Ebola crisis, lmao
Raspberry Pi Battery Power
20:34
ExplainingComputers
Рет қаралды 336 М.
Install a buck converter on YOUR 3D printer for the raspberry pi
8:13
Georges Gadgets
Рет қаралды 29 М.
WHO DO I LOVE MOST?
00:22
dednahype
Рет қаралды 43 МЛН
Чай будешь? #чайбудешь
00:14
ПАРОДИИ НА ИЗВЕСТНЫЕ ТРЕКИ
Рет қаралды 2,9 МЛН
Китайка и Пчелка 4 серия😂😆
00:19
KITAYKA
Рет қаралды 3,7 МЛН
DC-DC XL4015 CC-CV Module Test & Troubleshoot
16:53
SIRFLOOZ
Рет қаралды 13 М.
How to power Raspberry Pi and Arduino from LiPo batteries
18:36
Answering Your Pi 5 Questions | Cooling, Overclocking, Power and More
9:40
Raspberry Pi UPS? Do you need this?
6:01
Crosstalk Solutions
Рет қаралды 20 М.
DIY powerbank for Raspberry Pi 4. Part 1
8:29
Pavlo Khmel
Рет қаралды 7 М.
How to Power Raspberry Pi from your 3D Printer | Buck Converter 5V
4:11
Using cheap car parts to easily power your 3D printer's Raspberry Pi
11:27
2$ LiPo Charger & Boost Converter? || TP5410 Test
7:28
GreatScott!
Рет қаралды 533 М.
Drok Buck Converter | This Thing Rocks!
7:31
Ham Radio Tube
Рет қаралды 15 М.
Building a Touchscreen Android Tablet
6:01
Electo
Рет қаралды 679 М.
WHO DO I LOVE MOST?
00:22
dednahype
Рет қаралды 43 МЛН