Problems with Echo's 590 and 620

Рет қаралды 2,768

6 ай бұрын

Пікірлер: 35

@mfsaws8240 6 ай бұрын

I have never had a base gasket leak with dirko or moto seal. I have had a leak on a 500i with hylomar and I am very vigilant about cleaning the base and applying with gloved finger. So yeah only use it for piddly stuff. Good luck!

@bryanthornton6787 6 ай бұрын

You answered a couple of questions that i've been asking. I hope you get the saws figured out.

@glennmckinley3058 6 ай бұрын

Good video, we learn more from our setbacks that eventually become our successes. Videos are much more credible when things are not always perfect. You could have buried that but thanks for sharing it.

@stanleymason8155 6 ай бұрын

I would double check you didn't accidentally pull the impulse line loose! Just got a great deal on one that piston looked new I figured carb but somehow they had pulled or blown it loose. Acted very similar!

@michaelwhiteoldtimer7648 6 ай бұрын

I sure love to run my ported 590, it has plenty of power

@dubbssawshop 6 ай бұрын

IMO, ive tried Hylomar and a cheaper version and have had no luck with it, idk why, does great for some and crappy for others. Definitely doing the typical run around tuning issue.

@Super-Dave-Outdoors 6 ай бұрын

Motoseal and JB Weld do the same for me. Cant get either to stick to what i want and cant get it off of the things i dont want it on.

@dubbssawshop 6 ай бұрын

@@Super-Dave-Outdoors that's how it goes for some reason, Motoseal and 3B 1184 are my main go to. Little brake clean to clean it up and give it a decent coating. 👍🏻 Crazy how that works.

@Super-Dave-Outdoors 6 ай бұрын

I'm meticulous with surface prep, small engine mechanic for a living so no stranger to gaskets, adhesives, seals, etc. Certain products dont work for me, no clue what it is.

@Doc-Cole_Trickle-of-Chainsaws 6 ай бұрын

👍🆙👽

@charlesjenks2710 6 ай бұрын

great video.❤

@novicelumberjack 6 ай бұрын

Thanks, Charles.

@JandSChainsaw 6 ай бұрын

Use soapy water in a spray bottle

@TumbleweedRancher 6 ай бұрын

Yes, I have used this for low pressure (up to 50 psi) systems for years.

@forrestebert5276 5 ай бұрын

Hey Boedy did you check the decompression valve? Mine failed on my 2165 plugged it up and runs beautifully! Just a thought my friend!

@c3homeimprovementllc927 4 ай бұрын

The fuel filter is making it lean out stuck in tank

@c3homeimprovementllc927 4 ай бұрын

Hold saw on side and run

@c3homeimprovementllc927 4 ай бұрын

Is the fuel filter stuck on one side make it lean out

@Leave_Nothing_Stock 6 ай бұрын

So why not just run a base gasket? Has always seemed like the easiest option to me

@novicelumberjack 6 ай бұрын

These Echos have a stupid cardboard type gasket. I hate them. I discard them always.

@Leave_Nothing_Stock 6 ай бұрын

@novicelumberjack gotcha. You obviously don't do the volume make it worth the time, but I know donny has rubber coated gaskets made so he doesn't have to machine some saws. Wonder what that process is like

@Macgyver-ranch 6 ай бұрын

Has anyone used the wife's Cricut cutter to make repeatable gaskets?

@novicelumberjack 6 ай бұрын

@Macgyver-ranch I have a cricut. Could totally do it...but why would I?

@tedneitzel 6 ай бұрын

Yea it seems good under load but who knows maybe it can even be better once you get it running right!

@tjgrossman 6 ай бұрын

What do you use to set the timing gap on the flywheel? I have struggled with this every time!

@Super-Dave-Outdoors 6 ай бұрын

Index card, business card, piece of paper folder over twice, .015" feeler gauge

@brandonsmith3447 6 ай бұрын

Air leak I’d say. The revs raise b/c it’s leaning out when you’re doing nothing/ideling . I’m an idiot and approve this message. Loading up to me would lower the revs right, too rich??? Then it’s dying when I finally used up the juice.

@Doc-Cole_Trickle-of-Chainsaws 6 ай бұрын

👍🆙BigGuy

@aaronpowell4885 6 ай бұрын

Wonder if electrical contact cleaner would work🤔 definitely not as aggressive as brake parts cleaner. If it's leaking at the base, so far anyway, I've not had any problems with motoseal.

@lonnieholbert8898 6 ай бұрын

Do you delete the gasket on the 590? or have to cut it?

@novicelumberjack 6 ай бұрын

Both. Gasket delete and .010 from base.

@crazyfeller5704 6 ай бұрын

Definitely hunting around when it did idle.

@novicelumberjack 6 ай бұрын

I'll dive back in tomorrow and get it straightened out.

@Houseworksaws 6 ай бұрын

Is that saw advanced? I know some saws when advanced too far they will not tune out right. But you’re definitely trying to tune around a problem by the sounds of things. Hope it’s something stupid and easy because ain’t no one got time for that BS..

@novicelumberjack 6 ай бұрын

No advance. Gotta be leaking at the base. The cylinder skirt was pretty close, but it cleared accordingto the measurements. Didn't want to cut it if I didn't have to, but I may need to cut it.