How to Replace a Clutch plate pressure plate gear box refit mobile hgv mechanic Scania lorry truck

Рет қаралды 40,950

Chris Allen - Professional Struggler

2 жыл бұрын

Clutch pressure plate recon gear box re fit replaced Scania truck lorry hgv mobile mechanic semi rig mobile hgv mechanic

Пікірлер: 53

@lkreinmiller-author 2 жыл бұрын

Always amazed how mechanics keep straight the dozens of different jobs they do. Awesome.

@chrisstanton2333 2 жыл бұрын

Did this job for 32 years before retiring from it. Lining a clutch up by eye is always a bit dodgy as if you are the slightest bit out, you'll struggle. Easiest way is if you know someone at a metalwork company, ask them to turn one down for you. Even easier way is use an old 1st motion/ primary shaft from an old gearbox of the same type. Over the years I made up a collection of a dozen of them.

@jimmyquinn9639 8 ай бұрын

Lovely job Chris 🚛🚜🚚⭐️⭐️⭐️⭐️⭐️⭐️👍👍👍👍👏👏👏

@lukeframpton3671 2 жыл бұрын

Spot on I've always lined a clutch up by eye proper 👌

@brentsmith5647 Жыл бұрын

Brilliant man love watching and learning thank ❤️👀👀👀👀👀👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

@torquesteer2657 2 жыл бұрын

Good job pal 👍🏻

@charlescamilus8397 2 жыл бұрын

Good job mate I love the you explain and work I also getting some idea too thanks.

@davidhoy8363 2 жыл бұрын

Well done lad, used to do the same

@JoshuaJones-gb9ih 2 жыл бұрын

Mint video mate had me laughing all the way through

@Professional-struggler 2 жыл бұрын

Thank you mate! I hope you was educated as well 😂🤣

@patrickscanlon1631 8 ай бұрын

Wow sod ro doing gear box & clutch

@naisonmagonyo8509 Жыл бұрын

It's a stroogle, a big stroogle but we love it when it's in 😂😂😂😂😂😂

@mikebills9343 2 жыл бұрын

The age old problem of lining up the box ! I hate rolling about on the floor , specially now I’m nearly 65 , it gets harder to get back up 😂😂👍🏻😞😞

@mickyb90 2 жыл бұрын

chris professional struggler love it

@Professional-struggler 2 жыл бұрын

😆 well we are dieselmick, thanks mate

@patricksteele8007 2 жыл бұрын

What a funny happy Chavvy you really are. Keep on struggling mate.

@richardlaw5737 2 жыл бұрын

I’ve used a broom handle as a clutch lining up tool, wrap a load of tape around it so it’s a snug fit in the friction plate

@RobertSmith-fv3ux 2 жыл бұрын

Hi mate Proper work like me we love it Well I have to share this with you Had little iveco 10t for test checked over no day running lights which are also the side lights turns out it was the headlight at fault ,but you are advised to change both if one stops working the other one won't work& if you put one in &the other one has a fault it will destroy the new one £780.00 each what's wrong with a 20p bulb Have a great week end

@Professional-struggler 2 жыл бұрын

Oh my god that’s crazy! How do you explain that to the customer...... side lamp fault mate just call the bill £2000 🤣 yeah as you said what was wrong with a normal bulb! To much technology in simple things nowadays. Enjoy the weekend pal

@timpolis8620 2 жыл бұрын

If you can get your hands on a old gearbox input shaft and cut him in half you can use that as an alignment tool.

@sundramasiva2345 Жыл бұрын

Super

@mdtausif3934 2 жыл бұрын

Thank you sir

@andyg817 2 жыл бұрын

Ive had those spring pin bushes which are threaded, snap in half, especially front right. ,😃

@Professional-struggler 2 жыл бұрын

Just shows you they get some pressure on!

@johnwaby4321 2 жыл бұрын

If you don't struggle then the jobs not going right 😂😂😂😂😂

@125sm3 2 жыл бұрын

Do they not do a clutch alignment tool Like you use on cars?

@Professional-struggler 2 жыл бұрын

They do me old 🏍! And I’d advise any who hasn’t done one before to get one because it’s a sh*ter when you have to take the box out again because the plates in the wrong place lad🏍 💨

@aidanmitchell5345 2 жыл бұрын

Ah the old jeerbox job 😄

@stemartin6671 2 жыл бұрын

One of the places i worked used to cut the input shaft out of old boxes and use those to align the clutch up, and you’re right, it’s a total ball ache if you haven’t got them lined up 😂🤦‍♂️ even on cars they won’t go in it’s a f@cking nightmare pal 😂 top job btw 🤘🤣 And defo you just came up with the best explanation of being a mechanic pal- a professional struggler haha 😂 I’m using that one

@Professional-struggler 2 жыл бұрын

Yeah some places I go have some shafts it’s a good idea! That’s what we are mate strugglers 😂 thanks for the comment pal 👍

@stemartin6671 2 жыл бұрын

@@Professional-struggler struggle on pal 😝👌

@aldrinmartin3776 2 жыл бұрын

I once did a clutch where the starter fitted from the gearbox side, fwd car can't remember what it was. But it meant you could tighten the clutch cover AFTER the box was in position, made lining it up alot easier. Can you reach the pressure plate bolts through that big access hole on the Scania box ?

@FromMetayou 2 жыл бұрын

Was it an old astra they had like an inspection cover

@aldrinmartin3776 2 жыл бұрын

@@FromMetayou I know the old vauxhall novas had a cover on the bottom of the bell housing, you took the end cover off the gearbox allowing you to withdraw the input shaft. Do a clutch in 15min, without removing the box. The car I was thinking of was normal FWD set up , apart from the position of the starter motor, you could leave the clutch cover finger tight, mount the gearbox, and then tighten the clutch through the starter hole with an apprentice (me) turning the engine on the bottom puller to bring each clutch bolt into position. I want to say Meastro or Montego, but didn't they use VW gearboxes? .....

@hossainikbal1046 Жыл бұрын

im working with you

@simonmorgan7981 2 жыл бұрын

Cor sod that i stick to the warm scania workshop!!!!

@raymccarthy7492 2 жыл бұрын

Sealey do a good hgv clutch alignment tool kit does 90% of clutchs

@ChromeStacks 2 жыл бұрын

We have collected a of old input shafts over the years, have in a box in our workshop to use as dummy shafts makes the job much easier

@pietervorster5690 11 ай бұрын

How much do you torque the pressure plate bolts?

@hgvtechnician 10 ай бұрын

they meant to be 47nm

@simonelia8507 Жыл бұрын

Number professional strew

@russellmcallister6830 2 жыл бұрын

Proffetional strugglers and shite spellers we are!! Top lad chris

@archiegaming7584 2 жыл бұрын

Yes Robert

@Professional-struggler 2 жыл бұрын

What you think my lad? Good afternoons work 😬

@archiegaming7584 2 жыл бұрын

@@Professional-struggler when can I come to work with you again

@Professional-struggler 2 жыл бұрын

@@archiegaming7584 why does my work look fun 😂

@hollyallen7640 2 жыл бұрын

It doesn’t! 🙈 obviously just loves his daddy ❤️

@joshuawoodford9911 2 жыл бұрын

That bar is over kill for bolts that are meant to be 47nm on clutch plate 😂

@migsy2728 2 жыл бұрын

Fuckin ace

@charliewills8546 2 жыл бұрын

Never seen anyone put loctite on clutch bolts

@Professional-struggler 2 жыл бұрын

You have now 😂

@andygotting9152 2 жыл бұрын

If you aren't swearing at it be very wary you haven't missed something out.

@ibrahim-fr9tq Жыл бұрын