Program New Key Fobs To Your 3rd Gen 4Runner!

No video

Program New Key Fobs To Your 3rd Gen 4Runner!

Рет қаралды 61,499

Күн бұрын

In this video, I run you through the simple process of programming new key fobs to your 3rd Gen 4Runner (and other early 2000s Toyotas). The job only takes a couple minutes, but there are a few tricks you need to know to be successful, so stick around till the end!
Cheat sheet: docs.google.co...
New key fobs: amzn.to/4bSiF8N
Blank keys: amzn.to/4cSgq6V
Keyfob Covers: amzn.to/4d9a5DC
Cheers,
Carter

Пікірлер: 160

@mileseubanks5104 3 жыл бұрын

A couple tips I've learned - if the locks get tired either help them like shown in the video or lock and unlock the doors manually with the key in the door. Also, to see if your vehicle has keyless entry the chirper will be mounted to the passenger fender near the firewall in the engine bay (at least on my 01). The chirp volume can be adjusted levels 1-5, it is set at 3 from the factory. On my vehicle I removed the chirp completely.

@PartimeOverland 3 жыл бұрын

Right on! Thanks for sharing your knowledge brother! I'll pin this so people can use the info

@mileseubanks5104 3 жыл бұрын

@@PartimeOverland thanks!

@leetang1056 2 жыл бұрын

I think I have multiple door lock actuators that aren't working fully...Like it will unlock and lock once or twice in a row but after that it might be lacking power. Would I still be able to use the manual option to set my key fobs?

@andrewknasiak5290 2 жыл бұрын

Found using key in door easier than using the lock/unlock switch

@leetang1056 2 жыл бұрын

@@andrewknasiak5290 I guess I just need new actuators...mine wouldn't work at times when I use the key either.

@gregoryjohnson7824 Жыл бұрын

This is an excellent video on programming the third GEN 4Runner key fob. The most helpful part of the video was the suggestion to help the door actuator button move up and down at the same time that you cycled the lock and unlock button. I was unsuccessful in programming my key fob until I Executed this procedure. Then it worked perfectly. Nice job with the video!

@tbassiii 2 жыл бұрын

I’ve never seen a key fob work for a 3rd gen none the less program one... I was actually able to complete this with your video. Thank you!!!!

@kalesoup7633 2 жыл бұрын

Just did mine(2000 Sr5 sport) after struggling for so long. Thanks for the tip, only the drivers door needs the lock to move I just left the others unlocked. Got it first try and I also pushed the button in the door jamb. Thanks!!

@PartimeOverland 2 жыл бұрын

Brilliant! Love hearing that mate

@seanflanagan5211 Жыл бұрын

Thanks for the video and the cheat sheet. My son just bought an 01. It’s his first car and he’s very happy to have a fob that works!

@PartimeOverland Жыл бұрын

Brilliant! Glad you guys got things working. Tell your son he has the best car ever;)💪

@anthonyjimenez6902 Жыл бұрын

I know it’s been two years but man after literally 34 tries not exaggerating I finally got my key fob to program and it’s all thanks to your tip. Thank you so much man 😭🙏

@franciscojchandler3013 Ай бұрын

Thank you Senior. After a few tries and following your directions. I got it to work. I did have to do the manual pull of the lock button at the same time as exercising the internal switch . The lock actuator died after many tries. It all worked out just great. BTW this is in a 2000 4R. SR5 . Thanks again .

@Jefyb 4 ай бұрын

Worked perfect. I was ready to rekey the car and tried this. Fob works like it’s brand new. Thank you

@jaimesco2013 2 жыл бұрын

Thank you. Anyone having trouble I had success going slow and using one hand manually pulling the lock up and down in sync with my other hand switching the lock. I hope that made sense.

@genxiong2695 11 ай бұрын

Another tip if your actuators are not cycling properly or/shot and you've tried pushing down/pulling up on the driver's side door lock knob with no luck. Try this last option: You can manually use your key into the driver's door from outside and turned it back and forth (similar procedure as in this video 5). That was the only way I was able to get it to work as it was my last option.

@jdunn706 16 күн бұрын

This video successful helped me to fuck up my locks in my gen 3 4Runner making them not unlock or lock period with the buttons or key in the door!

@joyrdkid1 2 жыл бұрын

It worked for me. Had manually lock/unlock while using door switches. Thanks

@1malikalik 2 жыл бұрын

Woooohooooo!!! finally Chris Fix showed his face. Thanks Carter for the insight very helpful 👍

@PartimeOverland 2 жыл бұрын

Haha! How'd you know it was me;) Glad to help brother!

@1malikalik 2 жыл бұрын

@@PartimeOverland Anytime Chris fix. Glad you take humor very well. Looking forward to see more GREAT content from you.

@aidanbrom8117 2 жыл бұрын

Thanks so much for this. My actuator is also going out and I didn’t think I could do it by hand. Much appreciated

@OverlandPNW 3 жыл бұрын

Nice fob upgrade. I'm a big 4Runner fan and have an overland build. Cool channel. I'm in to see what you guys do in 2021. I clicked everything.

@PartimeOverland 3 жыл бұрын

Thanks for checking it out! We got lots of things in the works for 2021, stay tuned;)

@breidy07 3 жыл бұрын

It worked! Thanks so much .I did the trick where you pull and push the lock while you do the cycle because same as you my actuator stops working after you do it a few times.

@PartimeOverland 3 жыл бұрын

Awesome! Glad to hear it!

@neiro314 3 жыл бұрын

my actuators doing the same thing but i cant seem to get it to work still ive done it like 6 or 7 times and im scared to break my door lock lmao

@yolondafowler4285 6 ай бұрын

Thanks so much!! Thanks for suggesting manual lock and unlock option. Now the remote works.

@DreamWarrior1987 Жыл бұрын

I appreciate the tips at the end and I went back out and tried it with the other hand helping the actuator and it worked! Thank you 🙏🏽 I really appreciate your video!

@newcastleLvr 3 жыл бұрын

Great video!! The Google drive document was very helpful! I was able to do this in a matter of minutes!! Nice job. Thanks

@PartimeOverland 3 жыл бұрын

Awesome brotha! Thanks for the feedback💪

@newcastleLvr 3 жыл бұрын

@@PartimeOverland can multiple FOBs be programmed at the same time?

@jamesh.edwards6188 Жыл бұрын

Thank you! By far the best video on Key fobs!

@sarahmorris7618 2 жыл бұрын

Great resource - so appreciate getting the benefit of your precise directions

@AntonioClaudioMichael 2 жыл бұрын

Very informative video and Nice tips been trying for awhile to get 2 of my rigs to work that pull lock up with one hand while using the switch worked for me

@DavidRodriguez-hd3wt Жыл бұрын

Another tip. If your actuators are going out, you can use the key on the outside door handle perform the lock and unlock procedure.

@j.g.92 3 жыл бұрын

Never heard of this. Sweet tip!

@PartimeOverland 3 жыл бұрын

Thanks brotha! Glad to help!

@Andr3wTaylor Жыл бұрын

So my lock button works but my unlock button does not work. Will reprogramming the fob help?

@MortenDamm 6 ай бұрын

In the cheat sheet it says to hold the lock button for 2s. In the video you do the unlock button. Got my 1996 Prado turbo diesel to go into programming mode but the $22 fobs didn’t work. 😢 Great instructions though. Thank you 🙏

@Bru946 Жыл бұрын

I did all the steps correctly. At the very end it does it’s little unlock and lock when I hold down the unlock for 2 seconds. But after closing the door. Nothing happens when I hit the buttons again. Any idea?

@paulstark6414 Жыл бұрын

Dude! Thanks for the extended explanation.

@ChaddRainsFPV 2 жыл бұрын

Does this disable your old key fob from working? My spare got stolen, hoping for an easy fix 🤙 Appreciate the detailed vid brother.

@james9862 7 ай бұрын

Worked first time. Thank you

@solodare06 2 жыл бұрын

First try! Thanks so much for the help!

@sterlingwallstrum8975 Жыл бұрын

Great Video and resources, but I cannot get this working for my '97

@toddtrigiain7483 28 күн бұрын

2002 4runner needs to be in Valet mode first. Turn key on 3 times then remove key. Then key in one time and follow the 5 lock steps. Not sure you end with one turn key on at end or 2? I have seen both ways.

@jesrobles6405 Жыл бұрын

Just clicked on ur link and Amazon said it doesn't work for a 1997 4runner. What year is ur truck?? Would really like to purchase a key fob. Thanks

@tiamogonzalez3641 2 жыл бұрын

I having actuator issues too and can't seem to get it in programming mode. 😕

@stb1815 2 жыл бұрын

Thank you very helpful, great page btw

@mistermatsuda 3 жыл бұрын

That tip of helping the actuators out manually did the trick bro! Thank you

@PartimeOverland 3 жыл бұрын

Awesome, glad to hear it brotha!

@chrisburger4518 3 жыл бұрын

Great tip on the drivers door actuator going bad. My 01 has 142K miles and the actuator failed during the 5x on/off process. The programming would only work when I manually lifted the door lock tab up and down with each n'off cycle. Thanks!!!

@PartimeOverland 3 жыл бұрын

Glad to help! Those actuators are a pain... took me forever to figure that one out

@TrentsGarage Жыл бұрын

I have a 1999 SR5 with keyless entry (verified by original window sticker) and the rs3000 security system but I can't get the fobs to program. I am able to get it in programing mode but the fobs won't program.

@Matts-cars 4 ай бұрын

The VIP RS3000 appears to program differently than the ones in this video. The RS3000 was a dealer install (not a factory install) and the instructions are different. Sadly though, I can program the key fobs for the RS3000, but it seems to forget the key fob programming about an hour later. I have not found a solution for that yet.

@juliadeck-russell6664 2 жыл бұрын

We lost the keys and I had a new key made it’s obviously got the chip in it. I still have the original remote though. it doesn’t seem to be programming with anything I followed instructions carefully. It has new battery. when the door is open and I start doing the cycling it only locks and unlocks once and then the rest of the time it doesn’t respond to me pressing lock and unlock. anyone know the answer for sure?

@mr.mikepatino5968 Жыл бұрын

When I lock my front door, the alarm is set and will go off when I turn the key to ON. What should I do? Does the alarm setting mess up the sequence?

@PartimeOverland Жыл бұрын

It shouldn’t. Do you have an aftermarket alarm system maybe?

@justindoyle5972 3 жыл бұрын

So I bought a key fob got everything programmed but the rear window.how do you get the key fob to roll down back window?????

@Chromirage 8 ай бұрын

Just programmed mine thanks to your video. Maybe a stupid question but, does the window button only lower the window and not back up?

@Juan67_Az 2 жыл бұрын

Worked for me on 1999 toyota 4runner. Had to pull and push the lock to.

@PartimeOverland 2 жыл бұрын

Glad to hear it!

@GABRIEL_CRAFT 3 жыл бұрын

Great video and thank you for the links too!

@TheNancymikesc 5 ай бұрын

I just bought a 97 Hilux Surf and I need a fob. I’d like one with lock unlock and rear window up/down. Where should I get one?

@Sqwidwood Жыл бұрын

I have a question. Do you have the little box with a green dot under your driver side chair? I’m asking because mine doesn’t have it and I’m not sure if you need it for this to work. Thanks

@allenh7835 Жыл бұрын

Late reply ,but the black box can be under any seat or behind the drivers side kick plate. Dealer installed ,usually under drivers seat , but not always.

@fdr511 2 ай бұрын

I got the doors to lock and unlock but the rear window will not go up and down by the key fob, any help with that.

@potterportraits 2 жыл бұрын

Key to on twice clears all remotes. Key to on once let's you add 2nd remote.

@Matts-cars 4 ай бұрын

Any chance you have programming information for the earlier 3rd Gens with the dealer installed VIP RS3000 keyless entry system on board?

@Kyle-hf8dq 2 жыл бұрын

Will this work on a 97? I see on Amazon the key fobs say 1999-2009

@kimbrazo 2 жыл бұрын

Good lucking now brother you are the best

@hyenapeacekeeper2220 11 ай бұрын

Because of the rear glass button, I am going and getting a fob tomorrow 😂

@tynado1173 2 жыл бұрын

My electronic locks were too tired for this method. Locking and unlocking with the key in the driver door worked great though!

@bleach8672 3 жыл бұрын

Thank you for the video🙏🏻

@PartimeOverland 3 жыл бұрын

No worries, glad to help!

@allenh7835 Жыл бұрын

The box has 2 plugs. On my 97, one plug was disconnected. I plan to try it but expect to disconnect battery at 3am when it ???

@Mike_44 3 жыл бұрын

I recently bought a ‘00 4Runner Lmtd. The previous owner had an Autopage alarm installed but its key fob doesn’t work, all the door locks act crazy (some lock/open, some don’t) and I have to lock the doors manually before exiting the car. Is it possible to program the Autopage key fob as well or it has to be a Toyota key fob? Thanks for the video btw! Edit: I tried it on my car and unfortunately it didn’t work.. I hear this ‘ tick tock clock sound’ coming from under the steering wheel after using the key fob.. maybe all the actuators are bad on my doors, will have to look into it deeper. Thanks again.

@sammanning6178 3 жыл бұрын

I just bought a 00' 4runner Limited yesterday!!

@throbinhood3321 2 жыл бұрын

Could I use this for a lexus fob?

@rileymerline4858 7 ай бұрын

Do you need to do anything special for the rear window? Mine won't lower the window, but everything else works.

@tonyisme4934 3 ай бұрын

Can a 1990 4Runner have a key FOB? It has electric locks

@simonh2734 2 жыл бұрын

Thanks alot the manually pulling and pushing the lock worked ! Btw the rear window doesn’t work with the fob but does when i put the key manually into the hatch keyhole. Any tips how to make the key fob work for the rear glass? Also any clue how much the dealer will charge to cut and program the key??

@PartimeOverland 2 жыл бұрын

Sweet! Not sure about the rear window... I've heard mixed answers on that one. For me it worked - I would see if you can ask a tech at your dealer

@user-rh3tm7nk4l 2 жыл бұрын

very useful

@benkohout6495 10 ай бұрын

Having issues when I get the car into programming mode then press for 2 second and 1 second on the new remote and no response. Is there any tips for this part? I’ve see Hold unlock and lock and then hold lock. Also see unlock and lock and then unlock like in your video. No luck with either way any ideas?

@RosieTas 3 жыл бұрын

Good job. Very understandable. Like of course

@qt9195 2 жыл бұрын

This process will not work if you have aVIP RS3000 box under the driver seat. I have a 97 4Runner OEM fob PT398-07100. Check other videos for instructions. You have push and hold the green reset in for 5 seconds and the most important part is you MUST push the top button of your fob within the 5 second range. Mine finally worked after numerous attempts.

@goofsaddggkle7351 2 жыл бұрын

I have a ‘98 and trying to get it to program a used key fob I bought on eBay (same as my old one - heart shaped with 2 black buttons and a green button). Hope this works - that box you mention isn’t under my seat lol

@tynado1173 2 жыл бұрын

I have I programed but the window button doesn't work. Any suggestions?

@israelrodriguez6986 Жыл бұрын

Will this work if I have an aftermarket alarm installed with a different keyfob that is not the original???

@abiudflores3645 3 жыл бұрын

Everytime I unlock and lock my 4Runner it would stop registering and one door would be unlocked and another door would be locked and the process won’t work

@user-up1wy3sy8k 3 жыл бұрын

Somehow when I did this, I was able to program the new remote, but it un-programmed my old remote in the process. What did I do wrong? I cannot get it back in program mode.

@PartimeOverland 3 жыл бұрын

I've had the same trouble. For now I just have one fob programmed. If I ever lose that one I'll just program the new one. You can try the process again, but unless you really need both working, I would just leave it. Up to you if you want to futz with the programming sequence againXD

@SimplyThinkDreams 2 жыл бұрын

For anyone reading these comments, you must program all of the key fobs at the same time. Program one fob. Keep the door open and then do same procedure of holding lock/unlock for one second and then unlock for two seconds. Repeat again for any additional fobs.

@genxiong2695 11 ай бұрын

@@PartimeOverland Someone stated that Key to "On" twice clears all remotes. Key to "On" once let's you add 2nd remote.

@HenAndPenn 2 жыл бұрын

No 3 clicks :(

@blameabletub174 10 ай бұрын

So at the end when I program it. The door locks cycle when I press LOCK and UNLOCK on the fob, then I hold the LOCK. But it doesn’t program to my remote…

@mherson91 6 ай бұрын

Same problem here!

@mherson91 6 ай бұрын

Update-I kept at it and got it to work.

@brandontignor 3 жыл бұрын

Okay real question, So my 1998 came with the factory anti-theft keyless entry keys and so fast forward to now its not as accurate anymore and doesn't catch the unlock signal and when I need to get into the truck and use the basically "dead key" the alarm goes off and it goes into anti-theft and I cant start it until I FINALLY get the truck to catch the signal. Will this fix my issue or should I really go to the stealership to get it done there. :( Please someone have answers :3

@oklahomie22 3 жыл бұрын

Will this work if I have an alarm? With different key fobs already. Also, will the back window roll down after it’s programmed?

@PartimeOverland 3 жыл бұрын

It will reprogram the rear window, yes. Not certain on the alarm, but it should work fine

@denneyevangelista555 3 жыл бұрын

I noticed you were doing this on a facelift model, would this sequence and fob work for a pre-facelift as well? Thanks!

@PartimeOverland 3 жыл бұрын

Yessir! I've done some work on the front of my rig, but the programming should be the same for any 4Runner with keyless entry.

@denneyevangelista555 3 жыл бұрын

@@PartimeOverland awesome! Thanks!

@itsedwinguzman 2 жыл бұрын

I need some help I replaced my door lock actuators by changing the little motors and I been trying to program my 2 OEM remotes but sadly it just worked with one only which I want both of them programmed any solutions or tips?

@goofsaddggkle7351 2 жыл бұрын

Someone above mentioned if you turn the key on then off twice it actually erases all programmed remotes so just turn it on then off once to save already programmed remote.

@georgeheckard3109 2 жыл бұрын

I have a potentially stupid question. Will this work by doing the locking portion from the passenger side door? It's a long story, but the locking mechanism on my 99 doesn't register when the doors are locked or unlocked, but the passenger side does.

@eddoura 2 жыл бұрын

Answer: NO

@brucewayne2773 3 жыл бұрын

I called the dealer, according to my vin I do have keyless entry. tried to program it numerous times to the T. Even tried the manual lifting of the door lock tab as I pushed the lock/unlock. Do you know where the brain is located at?

@GuninGames 2 жыл бұрын

I've done the exact same sequence in my 1996 4Runner SR5 4x4 with an RS 3000 Toyota VIP Security box and I can't get my Runner to go into reprogram mode even after matching the exact same pace as you

@qt9195 2 жыл бұрын

I got the same issue with my 97

@nonsense6783 3 жыл бұрын

Does this work if I lost my old fob and want to replace it with a new one?

@PartimeOverland 3 жыл бұрын

Yes! That's exactly what I did in this video.

@denisgonzalezblandon1538 3 жыл бұрын

@@PartimeOverland does the vehicle turn on with the new key? after programming it or is it a different process just for the key and not the keyfob?

@joelreynaga4566 3 жыл бұрын

We’re did u buy the key cover

@PartimeOverland 3 жыл бұрын

Hey! Check the 4th link in the description. I just added it

@caydenvandeventer7423 3 жыл бұрын

Does this work with a fully stock 3rd gen?

@PartimeOverland 3 жыл бұрын

Yessir! Should work just fine

@darknessxshadow1045 3 жыл бұрын

Does this work for 1997 4runner?

@PartimeOverland 3 жыл бұрын

It should... I can't confirm for sure though

@JacobWithACamera 3 жыл бұрын

The actuators on my vehicle simply tire out too quickly, I’ve tried several times and the vehicle hasn’t gone into program mode. Will try later.

@mistermatsuda 3 жыл бұрын

Mine too but I helped it along with my hands, up and down... it' worked!

@JacobWithACamera 3 жыл бұрын

@@mistermatsuda I’ll have to keep trying.

@felixhernandez1242 3 жыл бұрын

@@JacobWithACamera did you get it

@JacobWithACamera 3 жыл бұрын

@@felixhernandez1242 Nope, my door lock actuator failed lmao.

@4rft5 3 жыл бұрын

will this work on a 98?

@eddoura 2 жыл бұрын

@fmidden8053 3 жыл бұрын

What do you do if your 4 Runner has push button start?

@eddoura 2 жыл бұрын

That is an aftermarket FOB. It will not work. It means, most likely, your 4 Runner did not come with an Antitheft feature.

@IronDuck1776 3 жыл бұрын

Will this work for a 1998?

@PartimeOverland 3 жыл бұрын

It should🤷‍♀️👍

@IronDuck1776 3 жыл бұрын

So for anybody with a 98 year model 4runner watching this video for guidance... Unfortunately the method used to program the keyless entry in this particular video does not work. But the good news is that the answer is simpler. With the car turned off and the drivers side door open, You just need to locate the electronic control unit under the drivers seat. Press and hold the green programming button on the side for 4 seconds. Then quickly turn the vehicles key from the 'off' position to the 'on' position and back to 'off'. Do this twice, but do not start the vehicle. Press the unlock button on the key fob. And unlock the drivers Side door. Then hold the green button again for seven seconds and repeat the same process with the lock button on the key fob and drivers side door. And its done.

@4rft5 3 жыл бұрын

@@IronDuck1776 did you get this fob from the video or a different one?

@IronDuck1776 3 жыл бұрын

@@4rft5 I had a slightly different key fob. But I tried the process I mentioned in the above comment with 2 different kinds of key fob and it worked both times for my 98

@alexescobar6297 3 жыл бұрын

@@IronDuck1776 could you give any more tips