Prototyping with Applied Science: Design and build a bite sensor

Рет қаралды 138,853

3 жыл бұрын

Join me in brainstorming and building a bite force sensor that allows paraplegic musicians to smoothly control an expression pedal. This video will include construction tips and tricks, methods, material selection, and a little design philosophy.
Tiny linear potentiometer used in final design: www.digikey.com/en/products/d...
Spring-loaded linear potentiometer: www.digikey.com/en/products/d...
Sil-Poxy for bonding silicone rubber to itself and other materials: www.smooth-on.com/product-lin...
Sorta Clear 40 - Platinum-cure silicone molding: www.smooth-on.com/products/so...
Light-cure 3311 adhesive: www.mcmaster.com/1700A253/ (expensive, but this tube will last a long time)
Blue lasers on eBay "5mW" wink www.ebay.com/itm/3-Packs-900M...
Braided shield, highly flexible, 4-conductor cable: www.digikey.com/en/products/d...
Fabric reinforced silicone sheet: www.mcmaster.com/8612K51/
Mechanical CAD on github: github.com/benkrasnow/BiteSensor
Support Applied Science on Patreon: / appliedscience

Пікірлер: 996

@mumiemonstret 3 жыл бұрын

You mean there are burglars that won't appreciate a scanning electron microscope or plasma sputter chamber?

@CamaroRick 3 жыл бұрын

Prob thought it was an old tv

@joshuahuman1 3 жыл бұрын

Sounds like they weren’t fans of the channel so at least its not a someone targeting him specifically from the channel

@parkerhuntington1360 3 жыл бұрын

Don't forget that oscilloscope 😳

@sasjadevries 3 жыл бұрын

Well educated people usually get a well paid job and don't have to steal. And if a burglar would be smart, he wouldn't be robbing garages himself, but he would set something up to decrease his own risk. (hire someone else, setup online scamming, hacking a bank account, etc) Just breaking open a garage is really one of the most primitive ways to steal someone's property.

@AlessioSangalli 3 жыл бұрын

@@sasjadevries sure, but I'm surprised Applied Science did not booby-trap his shop with all that stuff inside

@drink__more__water 3 жыл бұрын

I appreciate the honesty, or at least directness, of calling a product "Sorta-Clear"

@olik136 3 жыл бұрын

"is it clear? " "nah- sorta clear though! " "but how clear is that? " "40...it is about 40 clear "

@DrakeOola 3 жыл бұрын

@@olik136 Pretty sure he said 40 refers to the rigidity or durability of the silicone

@UltraBadass 3 жыл бұрын

well be careful kids if you get sued a lawyer might pick your products name

@vintyprod 3 жыл бұрын

@@DrakeOola it's a joke

@yunusalih 3 жыл бұрын

@@vintyprod its sorta funny

@matthewjohnstone7324 3 жыл бұрын

When your equipment requires so much education to sell that it's not even worth stealing

@jjoonathan7178 3 жыл бұрын

How much for a 10-gram baggy of sourcemeter? Asking for a friend.

@misterhat5823 3 жыл бұрын

Tweaker only after what they can pawn... Pawn shop wouldn't know what to do with most of his stuff.

@fanplant 3 жыл бұрын

What about the bong, sorry the molecular pump?? Did the pump survive?

@nomadpilot6442 3 жыл бұрын

This makes me very sad that some idiot is trying to smoke weed with that

@fanplant 3 жыл бұрын

@@nomadpilot6442 it probably didn't get touched and if it did could you imagine inhaling oil mist?

@hinz1 3 жыл бұрын

You should market these as TIG finger pedals. Old 2 button TIG torches are awkward to operate and foot pedal doesn't work if you're like lying under your car or in standing position, so that thing somewhat nicely integrated into a TIG torch would be totally nice.

@864awesomeness 3 жыл бұрын

I can't believe you were robbed by the grinch

@jimurrata6785 3 жыл бұрын

Many thieves watch the obituaries to see when a whole family will be at a funeral. Like its not bad enough you've just lost a loved one.... 😡

@johnpossum556 3 жыл бұрын

My brother in law was not there!

@kylejacobs1247 3 жыл бұрын

I guess the burglar didn't recognize a turbomolecular pump when he saw one.

@alaric_ 3 жыл бұрын

To be honest, i think he barely understood the difference between screwdriver and a hammer... Burglars are not know for their intellect.

@SeanHodgins 3 жыл бұрын

Half of prototyping is knowing when a design is a dead-end. Great explanation of your process. I guess the good news about burglars is that if there was a Venn diagram of "Can identify expensive scientific equipment" and "steals things from people's garages" the overlap is incredibly small.

@skipfred 2 жыл бұрын

Maybe he didn't want to be the only guy at the pawn shop trying to hock a homemade SEM

@treesap3749 3 жыл бұрын

Sorry to hear about your Christmas “anti-present”. It’s awesome how you were so light hearted about it!

@ZoonCrypticon 3 жыл бұрын

He needs to design an "anti-burglar" system to prevent these "anti-present" and "anti-pleasant" situations.

@longshot7601 3 жыл бұрын

Where were Daniel Stern and Joe Pesci on Christmas Eve?

@fpfree8821 3 жыл бұрын

I can tell you it's very hard to push a wheel barrow with one arm so be on the lookout for a two armed man that may be carrying out small paid jobs like moving some bricks or getting rid of some lawn clippings. Probably called Barry or something. Bazza. Lives within walking distance...

@TimLF 3 жыл бұрын

"you might be thinking" yes that's exactly what I was thinking.

@Arnogorter 3 жыл бұрын

Next up in Prototyping with Applied Science: Home security system

@alohathaxted 3 жыл бұрын

Home human disposal unit.

@paulstaf 3 жыл бұрын

Trunk Monkey Theft Retrieval System: kzfaq.info/get/bejne/sM-eZZmW39zLf2Q.html

@ActuallySettle 3 жыл бұрын

Yeah I want to see this guy do some high tech 'Home Alone' traps

@treesap3749 3 жыл бұрын

As a pianist, and someone with a working jaw, I really appreciate this!!

@sumduma55 3 жыл бұрын

How would your singing be affected by one of these? I'm wondering if a pad of some sort that you could tilt your head to engage and manipulate might be a better solution.

@bigiron4018 3 жыл бұрын

@@sumduma55 might be tricky because somebody without legs uses their whole upper body to balance when sitting usually, it’s more difficult than it is for able bodied people. So making it a head movement thing could put them off balance potentially. Could be wrong, just throwing out thoughts

@VeniceInventors Жыл бұрын

@@sumduma55 Was thinking about that while watching the video and quickly realized that the kind of motion used on a sustain pedal could quickly become uncomfortable as it often requires quick dampening between two notes on different cords

@whatsonchannelB 3 жыл бұрын

"building and trying is faster than trying to estimate what it is you want to achieve" -- there's some true hacker spirit right there.

@jason-ge5nr 3 жыл бұрын

most of that is incredible, but the most incredible is that you 'found' what you were looking for on digikey.

@bschena 3 жыл бұрын

har! exactly. only search Digikey when you already know what you are searching for...

@firstmkb 3 жыл бұрын

Kind of insane - fortunately they don't carry the cheap knockoffs too, as far as I know.

@AwesomeGames56 3 жыл бұрын

An interesting point, that super white lithium grease is what’s used in a lot of manual paper towel dispensers because it works so well with those types of plastic. My father did property management work (janitorial mostly) for a college and he would occasionally replace the grease in the dispensers on campus to keep them moving smoothly and it’s something I learned myself for use in some of my own projects.

@dittilio 3 жыл бұрын

This format of video should be mandatory for capstone projects, masters and PhD dissertations as preamble for final product presentation. There is SO much knowledge and value in being able to follow the path of reasoning, trials, errors, obstacles (burgled!!). And the key I think is that it's not 'judged', it's so relaxed and conversational. It's just, "I wanted to achieve A, by doing B, but ended up with C. I'm kinda okay with C."

@Flojer0 3 жыл бұрын

There are "mouthpiece pads" at music shops sold for woodwind insturments. That's what musicians use against bite damage.

@calchen6603 3 жыл бұрын

Every time you post a long form video I tell myself "Ah I'll watch some of it". Always end up sitting through the whole thing. This is the clear hallmark of an effective presenter

@hadinossanosam4459 3 жыл бұрын

As an amateur pianist, I do want to point out that (acoustic) piano pedals are not linear: they have a clear pickup point, where resistance suddenly increases and the transition of dampeners on the strings to off the strings happens, usually within only two or three centimeters of pedal movement. This has the benefit of enabling much faster pedalling (by limiting the effectively used range), and marking the half-pedal point. However, the original electronic pedal probably didn't emulate this, and given the short range of your sensor, it's probably not beneficial to do this and further shorten the effective range. Random tidbit: Grand and upright pianos have different dampener mechanisms (I think grands have gravity-return dampeners, which obviously wouldn't work for an upright), which leads to drastically different pedal feel between them: some uprights can have almost linear responses, while grand pianos tend to have very defined pickup points with sometimes annoyingly small effective ranges. As a result, half-pedal tends to be much easier to hit consistently on an upright than on a grand (but also has different effects, ...) Edit: Disclaimer: I play pretty much only acoustic pianos, so there may be some nuances to pedalling on electronic pianos that I am completely unaware of.

@AgentWest 3 жыл бұрын

A feel similar to that can be re-created by slightly changing shape of the ramps from basic slope. From what you're saying it would probably be better to have it steeper at first (less force, more travel of jaw. Easier to hold.), then to 45 around half way (linear, but the transition can be felt), then flatter (more force, less travel) near the end. Or maybe just two slopes with the transition half way?

@coal6tamarack2374 3 жыл бұрын

Some dude really broke into that shop and thought to himself "nah, expensive rubidium lasers and electron microscopy equipment - I’m just gonna steal a wheelbarrow and some cordless drills"

@jimurrata6785 3 жыл бұрын

They thought what am I going to pawn for my next fix? Burglars aren't looking for some unique thing that is going to attract attention or hard to get rid of.

@JLocke573 3 жыл бұрын

Anyone who's going to go around stealing out of garages is a fucking idiot so they probably didn't know what anything was besides the basic power tools.

@ameturephysicist 3 жыл бұрын

I wonder what the street price of an electron microscope is...

@evilplaguedoctor5158 3 жыл бұрын

I think Jim is closest, power tools can be sold with litre suspicion. Electron microscopes tend to have to small of a sales pool to blend in.

@Basement-Science 3 жыл бұрын

well burglars are usually poor and have very little education meaning they cant get a job. Not too surprising they wouldnt know what is worth something in Ben's garage.

@jatag100 3 жыл бұрын

Every non-engineer executive or manager needs to watch your channel. Especially this episode. This is excellent in clearly explaining R&D work and how prototyping without fully defined requirements is necessary. So many requirements can only be determined through prototyping. Excellent video!!!

@user-qf6yt3id3w 3 жыл бұрын

Imagine what a complete shit you'd need to be to burglarize someone's lab on Christmas Day and steal their tools.

@ChaosPootato 3 жыл бұрын

Especially Ben's, he seems like such a nice guy :(

@jhonbus 3 жыл бұрын

Probably someone with a serious drug addiction. There's only one thing that matters. Explains why all they took were tools, too. You know you can sell them to a pawn shop, and all that other stuff, although you and me know it's really awesome or expensive, is just an unknown variable.

@MrKfadrat 3 жыл бұрын

someone else got their presents though, slightly used, without invoice, but working

@horrorhotel1999 3 жыл бұрын

@@jhonbus That seems like an extremely prejudiced assumption to me. As a consequence of the pandemic lots of people have it really bad right now - aside from that there's a million possible reasons why you would need to resort to stealing. Glad to hear nothing irreplaceable was stolen, but I feel mostly sorry for the poor soul who was forced to resort to such extreme measures, no matter their reasons

@aerobyrdable 3 жыл бұрын

@@horrorhotel1999 Not sure why that's a prejudiced assumption. It seems to me you two are pretty much in agreement with one another

@johnyoungquist6540 3 жыл бұрын

You can tune the useful rotational range of a pot with silver conductive paint. It works with composite or wire wound.

@AppliedScience 3 жыл бұрын

That's a great idea!

@siggyincr7447 3 жыл бұрын

I was wondering how you were going to glue those silicone parts together. Always fun to learn about a tool/product you didn't know existed but could come in handy in the future.

@artemiygolden2853 3 жыл бұрын

The potentiometer laparoscopy was amazing!

@finnsuchara1992 3 жыл бұрын

Fiber coupled microscope lense would be supper cool. Also did you know they did surgery on grape. "Allegedly" :B

@MisterPornthep 3 жыл бұрын

I usually buy the smaller tubes of Sil-Poxy because eventually the tube will harden all the way once opened and I don't use them that often.

@firstmkb 3 жыл бұрын

WSINW If I was as smart as Ben, I would store all of my glue under pressurized argon, and it would still be good when I wanted to use it. But I'm not.

@rlrfproductions 3 жыл бұрын

Two things that came to mind watching this: 1, have you taken into account possible toxicity of the glue and grease? 2: Once hermetically sealed, won't crushing the device increase internal pressure and add back some of that pneumetic 'bounciness'?

@N4w4k 3 жыл бұрын

I would also add: how many volts does the piano send into that potentiometer? Is there a risk of electrical shock?

@EdTannenbaum 3 жыл бұрын

1: It looks like the tube with the wire in it will equalize the pressure.

@JTLaser1 3 жыл бұрын

The fun in inventing something that currently doesn’t exist is the thousand things you learn along the way. I came up with a patented LASER optical delivery device in my back yard, and I’ve never had so much fun!

@alakani 3 жыл бұрын

For the pneumatic version, you could try using a MAP sensor from an old GM to read the pressure, they're a couple bucks at the junk yard. Maybe use an arduino to read it and flatten the response curve in software, have it drive a digital pot for the output, it'll probably be fine. Chewing on squishy things is fun

@kebakent 3 жыл бұрын

That ramp design was pretty cool. I really like how the pressure distribution should be irrelevant. I wonder if this would be applicable for keyboard designs.

@nipunagunarathne4882 3 жыл бұрын

spacebars already have a mechanism to achieve that, but it's different

@Kori-ko 3 жыл бұрын

I'd imagine using such a stabilization method would be incompatible with everything too

@BlayneMahoney 3 жыл бұрын

Guitar hero frets yo.

@EdwardTriesToScience 3 жыл бұрын

That design is so simple yet so effective, and sad to hear that your shop was robbed

@mp6756 3 жыл бұрын

Thank you for breaking breaking down the most difficult part of design down into bites Pun intended. Showing the reality that the first, sometimes simplest idea convinces the builder he has found the ultimate solution. At least I have done that too many times. I will beat my original idea to death before I realize it wasn't such a great idea.

@rpavlik1 3 жыл бұрын

You're so right about how the best solution looks simple but required all the steps to get there and a process that was not simple.

@electronicsNmore 3 жыл бұрын

Congrats on reaching 700k!

@fonkbadonk2957 3 жыл бұрын

Hold on a second. This channel is still sub 1M!?!? What the...? I've been watching for several years by now, and always assumed that he is way over 1M even back then. I've never actually looked at the number. Heresy!!

@tijssens 3 жыл бұрын

How can the best channel on youtube only have 700k subs. I send shares to all my geeky friends!! Do your best fellow science nerds :)

@johnmccanntruth 3 жыл бұрын

That’s a pretty cool solution you’ve come up with. I’d be interested to hear the feedback from the musician. And will there be further tweaks...? Anyhow, thanks for sharing! Oh yeah, forgot to send my condolences along for your tools. I’m glad you weren’t hurt, tools can usually be replaced. God bless!

@karljay7473 3 жыл бұрын

Amazing! I want something like this to control the pedal on a TIG welder. The thing about it is that it's much larger, so I'm not sure if there's a way to do that. Maybe have one small one that controls a motor that controls a larger one. Use one of those to simple control a powerful stepper motor that controls the pedal. Make it into a trigger control and put it on the TIG torch. Interesting.

@DanieleGiorgino 3 жыл бұрын

I've gotten into silicone casting and have been having a lot of problems with bubbles. I love how you barely mention your process and all of your castings look perfect.

@Steve_Just_Steve 3 жыл бұрын

I think he's shown it the past and he did mention how to prevent bubbles.

@DanieleGiorgino 3 жыл бұрын

@@Steve_Just_Steve Yes, the solution is to just buy a vacuum chamber but Ben's so blasé about it it kills me.

@Steve_Just_Steve 3 жыл бұрын

@@DanieleGiorgino Or make one. Or I think you can find a cheap old pressure cooker and use it as pressure pot, but I know what you meant.

@SkigBiggler Жыл бұрын

@@Steve_Just_Steve I’d second this. Did it myself. A slab of acrylic and an old pressure cooker are all you need. Cut a ledge into the acrylic and make a seal using silicon, then plumb some sort of fitting for the vacuum hoses. It doesn’t need to be super precise if you’re not getting down to super lower vacuums, cause the vacuum will pull all the parts tight and prevent leaks.

@ericlotze7724 3 жыл бұрын

I'm adding this to a list of HIDs for an OS version of that "Xbox Adaptive Controller" system. Amazing Project (As Always lol)

@danielpirone8028 3 жыл бұрын

Yamaha used to have breath controllers ( introduced back with the DX7 )

@SianaGearz 3 жыл бұрын

Breath controllers are pretty standard, but they are not very good for a pianist as a pedal replacement. Because you can continuously press down on the pedal for pretty long phrases - potentially indefinitely - but you can't really breathe out continuously, you have to breathe in once in a while. Also breath strength control is not so precise, you get expressive phrases, but you can't just hold the same exact airflow. Also i think they're digital and connected via MIDI.

@danielpirone8028 3 жыл бұрын

Great point!

@twdodd439 3 жыл бұрын

Im only 13 minutes into the vid but i got a suggestion..... what about using the tongue. The lips and teeth anchor the device and the tongue operates a lever within the mouth cavity. the paddle could stay low and you lift the paddle to activate. that would allow for both rapid and incremental/analog positioning. Sorry to hear about the robbery, you're a great guy that just wants to teach. Thanks for the great content!

@pulesjet 3 жыл бұрын

You can also sandwich some conductive foam between to metal contacts and create a variable resistance source.

@wuddadid 3 жыл бұрын

Been rough without a video these past few months

@jong2359 3 жыл бұрын

I am sure being burglarized on Christmas supersedes your feelings of perceived loss for something that is given to you for free.

@anonymousarmadillo6589 3 жыл бұрын

@@jong2359 He was joking, no need to be so edgy about it.

@alangunn7254 3 жыл бұрын

Ironic that the answer to a bite sensor was "Teeth" :-)

@ic3l0s 3 жыл бұрын

Would be nice to see an update on how it performs in actual use by the player. Very cool to see the different iterations and realizing there are more boxes to tick than previously thought. Makes me appreciate a well designed product that just works and is intuitive.

@rdoetjes 3 жыл бұрын

I glue silicone with the same silicone. No need for an extra product. And the advantage is that you can make your “glue” as liquid as you want by thinning it down with naphtha. And always for skin and mouth use, use a platinum silicone. That’s non toxic, I believe smoothing is all platsil. And a good Platsil sets in 20-50 minutes that’s also nice :)

@Rapidpanda1st 3 жыл бұрын

Another plus for the ramp design is you could change the shape of the ramp to create perceivable 'steps', or even give it a curve to change the felt spring rate.

@Reth_Hard 3 жыл бұрын

The first thing I would've try is to make something using a bicycle brake cable with, of course, a potentiometer and a spring at the end of it. For the mouth piece you can just 3D-print something, not quite sure exactly what would be best shape/mechanism, and also I'm not sure if the brake cable would have a bit too much friction to work well...

@martin_mue 3 жыл бұрын

A PTFE lined bowden cable was my first thought as well, stiction should be acceptable. It could even be routed through a gooseneck pipe mounted to the keyboard. That would allow the user to position and "store" the mouthpiece relative hygienic in air.

@tymekuzarczyk6021 3 жыл бұрын

That's awesome. Everything: you helping disabled person, design process and showing it to us

@ronniepirtlejr2606 2 жыл бұрын

The best thing I can think of that has full feedback is Hydraulics, like what's on a vehicle. Or at least partially hydraulic. I cannot wait to finish watching the video & see what you came up with.

@KJTmcG 3 жыл бұрын

Gotta wonder what kind of burglar would fail to second guess themselves after a quick glance at the contents of your garage!

@fischX 3 жыл бұрын

@@pleaseyourselfsir gosh, bring your political bullshit somewhere else.

@jimurrata6785 3 жыл бұрын

@@fischX Thank you! 😎

@AtlasReburdened 3 жыл бұрын

Well, the idea of being a burglar, and the idea of being a deep thinker don't really mesh well in my head, so I'd say probably the normal kind.

@electrontic 3 жыл бұрын

This is basically what I do at work, and it's really cool (and educational) to see someone go through the same process! This was great!

@rossmiller2204 3 жыл бұрын

Disheartened to hear about the burglary, but glad to see it didn't get you down! I wasn't aware of anything that could adhere well to cured silicone, which got me to thinking: a video about adhesives (especially for plastics/difficult to bond materials) similar to your video regarding cleaning solvents/detergents, would be amazingly helpful to a wide range of viewers.

@321tryagain 3 жыл бұрын

Absolutely brilliant insight into your design process. Thank you.

@forestlampcraft472 3 жыл бұрын

COOL!

@lidarman2 3 жыл бұрын

As a laser guy, I can't stop looking at your breadboard.

@hpekristiansen 3 жыл бұрын

Next christmas, I will take that instead of tools - I now know it is worth more.

@AppliedScience 3 жыл бұрын

We'll soon have some good demos done with the new optics toys! It's also amazingly convenient for mechanical fixturing and adjusting of all sorts assemblies.

@lidarman2 3 жыл бұрын

@@AppliedScience My go-to phrase is "Hand me a 3/16" ball driver."

@tophan5146 3 жыл бұрын

I hate that the youtube algorithm forgot to show me this channel. Thankfully I randomly remembered it.

@Teklectic 3 жыл бұрын

PETG might make a better FDM prototyping filament than PLA for applications like this due to it's greater durability and food safe properties; I think with a bit of clever rearranging this exact design could be acceptably reproduced with FDM :) So much good information here, thanks for sharing!

@TechGorilla1987 3 жыл бұрын

This is something I can really sink my teeth in to!

@Mireaze 3 жыл бұрын

Boooooo!

@ASCENDANTGAMERSAGE 3 жыл бұрын

Me like pun

@ethan-loves 3 жыл бұрын

Very cool! Thank you for sharing. I'm curious, have you ensured that all of the exposed surfaces of the sensor are made of non-toxic materials?

@bf0189 3 жыл бұрын

Sorry you got burglarized during the holidays and no worries about the lack of videos! I'm just glad you're okay and they didn't steal anything exotic. I found your struggle to find the right lubricant very interesting and useful in the future if I ever use the same silicone for a project.

@benjaminshropshire2900 3 жыл бұрын

It'd interesting that a lot of videos I've been finding lately have been dancing around the question of upfront design vs build and iterate. Scott Manley and his videos about SpaceX and SLS, Wintergatan and his progressively more pragmatic work on the MMX, Doug and his design philosophy for SV Seeker of "We build it right because we build it twice".

@karlm5022 3 жыл бұрын

Probably waring a gum shield might be a solution for puncturing the silicone

@solarcrystal5494 3 жыл бұрын

Can your next project be a homemade security system?

@NiHaoMike64 3 жыл бұрын

Perhaps with some energetic yet safe chemical reactions as the alarm? (Like firecrackers but substantially less likely to start a fire?)

@wahyutriwibowo1803 3 жыл бұрын

@@NiHaoMike64 or maybe active denial system using mid-power microwaves like those on US military?

@anonymousarmadillo6589 3 жыл бұрын

@@wahyutriwibowo1803 High power laser beam with OpenCV based eye tracking.

@wahyutriwibowo1803 3 жыл бұрын

@@anonymousarmadillo6589 High-power Infrasound speaker for some artificial spooky feeling

@MrAidanFrancis 3 жыл бұрын

Time for a LockPickingLawyer colab

@CarlMarvin 3 жыл бұрын

Love that you're uploading again! This project was fascinating. Watching the design flow had me interested the whole time

@Peter_A1466 3 жыл бұрын

You can't use elastic hoses in a hydraulic system. 😁 Nice video, once again I learned a lot! Sorry to hear about the burglary.

@Steve_Just_Steve 3 жыл бұрын

But everything is elastic.

@Peter_A1466 3 жыл бұрын

@@Steve_Just_Steve everything is elastic, but some are more elastic than others...

@Steve_Just_Steve 3 жыл бұрын

@@Peter_A1466 Was just joshin' ya.

@Peter_A1466 3 жыл бұрын

@Anifco67 changed it 😁

@UncleKennysPlace 3 жыл бұрын

You use the SpaceX design philosophy! You need an alarm. With a gamma ray emitter.

@NiHaoMike64 3 жыл бұрын

Or some item that looks like a nice power tool but is actually a smoke bomb. So it gets stolen and then 5 minutes after the thief leaves with the loot, there's suddenly a huge amount of stinky smoke. Another idea is a radio jammer that activates if stolen, if such a device is legal to own but not operate.

@SianaGearz 3 жыл бұрын

@@NiHaoMike64 As much fun as thinking about setting traps is, i wonder if they in turn make for legal pitfalls for the property owner. What if the burglar trips because he's frightened by a smoke bomb and injures his ankle? Might sue the property owner.

@uint16_t 3 жыл бұрын

Love the design process and all the considerations!

@nixxonnor 3 жыл бұрын

Awesome brainstorming, troubleshooting and solutions

@DarkOoze123 3 жыл бұрын

A hall effect sensor with a rotating/sliding magnet should be able to work as a potentiometer with low friction.

@bschena 3 жыл бұрын

linear-output Halls output a voltage, not a variable resistance, so it may or may not work properly as he mentioned not knowing exactly how the "inside" circuit is constructed.

@SonOfSofaman 3 жыл бұрын

I had to look up "lubricious". Turns out there are two definitions, one of which is not in any way applicable in this context.

@joooooooooooe 3 жыл бұрын

I googled. I laughed.

@Crabe05 3 жыл бұрын

This is such a cool project! And a very great hindsight into engineering processes in general!

@TheDrunkenMug 3 жыл бұрын

Lovely workmanship, well done !

@Spirit532 3 жыл бұрын

Are there any concerns about health safety with the silicone, and more importantly, the epoxy and the high temp pads? For something that goes into someone's mouth, I'd be a bit concerned about that, besides just waterproofing.

@SianaGearz 3 жыл бұрын

Epoxy is not a health concern. It crosslinks completely (after a while - maybe wait a week after it has cured until you declare it safe) and becomes pretty close to inert. Even if you break off and swallow a chunk, even if it's slightly contaminated, you can pretty much assume that nothing will come out of it. Silicone is not generally known for potential contamination during manufacturing, but if there was a contamination, it would potentially leech out. Eh, small risk i guess :D

@JeffDriskill 3 жыл бұрын

...and if the silicone fails what about that lithium grease?

@Spirit532 3 жыл бұрын

@@JeffDriskill You'll taste it immediately, lol. Highly caustic.

@SianaGearz 3 жыл бұрын

@@JeffDriskill Many people have accidentally ingested small amounts of grease and lived to tell the tale, it's probably not good for you, but it's not highly toxic either. But since the silicone is slightly water permeable, it seems like it would potentially breed bacteria, especially as it accumulates damage. I think the device should simply be re-shelled regularly. Or maybe used in a protective sheath of some kind, like a piece of medical glove, a finger cot, a... pardon me, what's your first Google hit on "latex dry bulk disposable microphone cover"? :D

@SianaGearz 3 жыл бұрын

@@jorje58965 The silicone glue is for sure a complete misnomer, it's a weld, not a glue.

@zdog90210 3 жыл бұрын

I think the final design is like abstract art where everyone thinks they can do it, but as an art teacher said "well then why didn't you do it?"

@paulblair7515 3 жыл бұрын

It's the little things in these projects, those little tips and tricks that can be used for so many other things I find most valuable. Excellent video thank you

@rogerbeck3018 3 жыл бұрын

i loved the detail of you thinking, and the value of time in research

@TheTsunamijuan 3 жыл бұрын

@Applied Science , Could you explain how you went about finding safe adhesives/materials for interfacing with a mouth. I know smooth on makes a number of food safe materials. But It seems like adhesives and possible after tastes from compounds could be a problem. I know you have many years of developing human interfaces. But this one certainly seems to add additional problems.

@bschena 3 жыл бұрын

agreed. I was hoping to hear the words "biocompatible" or at least "non-toxic" - though, to be honest, most Silicones are...

@kajraske2002 3 жыл бұрын

Sounds like they took stuff they felt they could easily sell, really.

@TJStellmach 3 жыл бұрын

Yeah, a lot of comments here talking about how valuable that scientific gear supposedly is, but stolen goods are only worth what you can easily sell them for.

@steezydan8543 3 жыл бұрын

Yeah I'm in a trade school ATM and the teachers have a thousand stories about students stealing things, and then them finding it online only a few days later. All of our tools and machines have our school's name physically etched into it, so someone steals a 500 dollar multimeter and they don't even bother to grind off the goddamn school's name before they put it up for sale. Many such cases.

@rantaoca491 3 жыл бұрын

I really appreciate you talking through your thoughts during the design process

@rockyrivermushrooms529 3 жыл бұрын

Awesome! I always enjoy watching your projects.

@drink__more__water 3 жыл бұрын

I think you just made a very fancy MX Cherry Red switch lol

@bschena 3 жыл бұрын

Cherry Reds are still just binary switches, not linear output like what he's making here.

@drink__more__water 3 жыл бұрын

@@bschena True, I was more reffering to the 'feel' of the switch. So it's more of a very very fancy red switch :P

@matthewellisor5835 3 жыл бұрын

I hate to hear that about your shop being burgled. Even when it's just stuff, it's still a violation and the emotional hit of "someone was in my shop/garage/car/house" sucks. I cannot abide a thief. Now, before anyone might say to think of the other guy who might be so down that he saw no other option, I call that victim-blaming. I've never turned away a person who, coming to me, asked for help. I have had my offers of help rejected far more often than not!I've had to ask for help, been turned down but kept trying until I found it.

@ScottCard 3 жыл бұрын

Nice project. I use those pots as low-cost extensometers. They are great because they are disposable when things go wrong!

@cls9474 3 жыл бұрын

Thanks a lot for this nice assortment of techniques and parts useful for a variety of projects!

@55Ramius 3 жыл бұрын

I assume a elabrate alarm system will be added or mods to one already there to raise hell if somebody comes in. It is sad this happens.

@0xbenedikt 3 жыл бұрын

Is the final product completely non-toxic?

@SianaGearz 3 жыл бұрын

It's a good GUESS that it's likely nontoxic, even if the materials don't come with FDA or equivalent approval, the reactions used in manufacturing aren't known for toxic side products. I'd say the poisoning risk is pretty much zero, even if it turns out that something in the surface layers isn't entirely kosher. Also biting all the way through and ingesting grease wouldn't be great, but it seems a little too inert to be really dangerous. Now that you got me thinking and Ben mentioned that silicone actually has quite a bit of water permeability, i'm wondering about hygienic situation though, what the replacement regimen on the outer cover should be.

@gth042 3 жыл бұрын

That reinforced silicone is likely cured with something pretty nasty. Good (excellent) proto version though!

@JeffDriskill 3 жыл бұрын

This was my concern as well. This is something that would be in the pianist's mouth A LOT.

@AppliedScience 3 жыл бұрын

@@gth042 Actually, it is FDA compliant for contact with food.

@gth042 3 жыл бұрын

@@AppliedScience Sweet, fiber reinforced too. Handy for ...things :)

@netmagi 3 жыл бұрын

Outstanding video! Really enjoy the way you shared the challenges and your thought process for solving them.

@ChengIan 3 жыл бұрын

Really enjoy watching the evolutionary process behind an engineering build, and all the tips and tricks, this video has taught me so much!

@sendep7 3 жыл бұрын

lithium grease in someone's mouth....? also is the smooth on food safe?

@rogeriocosta1035 3 жыл бұрын

Yes. There are food grade lubes over there. I would try then before go to the lithium.

@krzysztofswitkowski5364 3 жыл бұрын

It also was the first thing that worried me. Lithium grease is not the best choice for the device in mouth. I would also avoid MoS2 etc. In fact silicone grease is wide used in food production machines, but pity its not working here well.

@matgggg55 3 жыл бұрын

Dam good thing that burglars are stupid , I would have had a field day in your shop! Lol but I’d never steal

@UpcycleElectronics 3 жыл бұрын

I'd get caught for sure. After entering I don't think I could muster the strength to leave the Cave of Wonders.

@TJStellmach 3 жыл бұрын

Sounded to me like they stole stuff that could easily be sold on the secondhand market, no questions asked. Nothing stupid about that, if you're a burglar.

@mib5116 3 жыл бұрын

Heart warming project, great example of problem based learning, great video!!!!!! Cheers mate

@absalomdraconis 3 жыл бұрын

Something you might try if you ever get another request like this is a leaf spring in a parabolic shape, with an led & photosensor focused on the internal surface. By changing the spacing of the spring's ends, you get both a different focal spot, and a different restorative force from the spring. I think it was in relation to some game console that I first heard about this technique.

@fascistpedant758 3 жыл бұрын

Within a two week period they stole most of my mechanics tools in my garage and then the tools I had at my sons cottage which I was renovating.

@changeagent228 3 жыл бұрын

Surprised you didn't use a hall sensor.

@mckenziekeith7434 3 жыл бұрын

Watch the video again. He explains that it has to be all passive in order to mimic the existing pedal. Hall sensor is a powered circuit.

@SianaGearz 3 жыл бұрын

@@mckenziekeith7434 It doesn't strictly HAVE to be all passive if you can find a purely resistive way of interfacing, such as via two LDRs - but that is prone to issues too. Passive is the best solution for sure. I think you don't even have to use that particular input - you can use MIDI IN on the instrument and just feed it CC64 on all channels or on a channel mask or channel selector.