2019 - 2023+ Chevy / GMC Truck Amp and Subs Install

Рет қаралды 112,551

Жыл бұрын

Parts linked in the description below!
Watch a full tutorial as a 2020 Chevy Silverado will have four new Skar Audio 8" subwoofers and Kicker 1800w RMS amplifier installed. We will also be using an AudioControl LC2i and Epicenter for our line out converter and signal EQ for our amplifier. These amp and subs will be integrated to the factory audio sound system.
Note: This vehicle was equipped with the Bose amplified system from the factory. We will be retain the Bose audio system fully, and this install only integrates into the factory subwoofer for signal. If you do not have Bose, you will need to obtain your signal from your rear door speaker channels or behind the factory radio.
This video applies to Chevy Silverado or GMC Sierra trucks for years 2019, 2020, 2021, 2022, 2023, and newer. This video also includes amp rack installation, wiring, and testing.
Non-Bose Chevy / GMC Truck Stereo wiring diagram (if not using the T-harness):
Front Left (+): Blue
Front Left (-): Brown / Blue
Front Right (+): Yellow
Front Right (-): Yellow / Black
Rear Left (+): Green
Rear Left (-): Green / Black
Rear Right (+): White
Rear Right (-): Blue / Black
Click here to see the front door speaker install on this truck:
• 2019 - 2024 + Chevy / ...
*For the rear door speaker install, click here:
*For a multi channel amp(s) install, bypassing the Bose amp, click here:
• 2019 - 2024 + Chevy / ...
If you have any questions, leave a comment below! Be sure to like and subscribe!
Parts Used (Amazon Associate / eBay Partner Paid Links):
*Skar Audio 4 Gauge OFC Wiring Kit: amzn.to/31f0r2U
*Skar Audio SDR 8" DVC 4 Ohm Subwoofer(s): amzn.to/42L1IbK
-Recommended amplifier for those subs: amzn.to/46EiWdP
*GM Truck Box for (4) 8" Subwoofers Ported: amzn.to/43wikVh
*AudioControl LC2iPro: amzn.to/42kWnYU
*AudioControl Epicenter: amzn.to/3Kp2zGw
*1' RCA Cable(s): amzn.to/44z1hmW
*Metra 9 Conductor Speaker Wire: amzn.to/3xK4PSk
*Rear Wall Amp Rack (non paid): soundsgoodstereo.com/products...
--If you are looking to add a MULTI-channel amplifier, or multiple amplifiers and want to totally BYPASS the factory Bose amplifier, you will need:
*Axxess AXDSPX-ETH1 DSP Bose amp bypass kit: amzn.to/3SwJsBe
*NOTE - If you DO NOT have the factory BOSE Audio system, you will not have a factory sub to tap into, instead, use this T harness at the radio to connect your speaker wire to your line out converter. This depends on the factory radio, refer to Pac to determine which harness is needed for your install:
*Pac LPHGM71 Radio T Harness: amzn.to/3Uk7GA9
OR
*Pac LPHGM72 Radio T Harness: amzn.to/49r2Y83
Disclosure: As an Amazon Associate / eBay Partner I earn from qualifying purchases

Пікірлер: 246

@ProvoBeastAudio Жыл бұрын

Parts used linked in the description of the video. Check it out!

@yuniordelacruz3628 2 ай бұрын

I have a 2023 gmc elevation non bose audio will that amp rack fit on my truck?

@MerleHaggler Ай бұрын

@@yuniordelacruz3628yes

@fulanito47 Жыл бұрын

i love it! good job! very clean!!! I'm actually looking forward on buying this truck in the near future.. pretty much what i want to do also. props to sound good stereo for making that amp rack!🤩

@timothymedders7110 3 ай бұрын

Just wanted to say thanks for posting this. I installed quad 8's in my 24 GMC SLT. It was easy with this excellent video.

@davidrendon9838 2 ай бұрын

Did you have a problem with remote unlocking doors and turn on the Amp? Like a couple of others have commented about?

@ClemsonNigel 10 ай бұрын

Wow!!! This set up is so clean. I have a 2020 AT4 with the same Bose system so this video is exactly what I needed. Just wish SC was a little closer to Utah so you guys could do it lol

@ProvoBeastAudio 10 ай бұрын

Give it a go yourself! All parts we used are linked in the description.

@tosby1 6 ай бұрын

South Carolina? What's the name of the shop

@juliansdiamonds 8 ай бұрын

This job is absolutely 💯 beautiful !!!! Thank you for this !!!!

@19gkk1le5 11 ай бұрын

Huge thanks just picked up a 23

@frubalcava2208 Жыл бұрын

Everything looks really nice 💯

@itz_andyt 5 ай бұрын

Amazing job well organized 🔥🔥

@johnathanstarnes2149 5 ай бұрын

Super clean great job

@victorreyes4971 2 ай бұрын

Option one: You would have to remove the seat every time you want to make quick or minor adjustments. Option two: leave the rear passengers without a comfortable back rest 😅

@gyfhj 8 ай бұрын

Great video Brother! 💪🏼

@19gkk1le5 11 ай бұрын

Crazy clean 👌

@henrythompson5624 10 ай бұрын

Super clean setup I wish you guys can hook up mine

@aisensoto190 7 ай бұрын

Could you do a video on how you do the wiring with more detail and how you make it look that clean

@gumbeelee21 Жыл бұрын

Nice job!!!

@redsmith882010 5 ай бұрын

Wish i would have seen this video on the amp rack, i did how ever order the same one recently. I also went with a T-harness from LLJ Customs that plugged into the bose amp and left pig tails for the LC2i. My problem how ever was finding the right size amp to fit behind the seat....if it's over 2.5" tall, the seatwon'tt fit. I was using the SFB2000 for almost 3 years before the cooling fan quit working.Took some time to find a new a new stronger amp but, found the DC Audio 3.5k that fit perfectly...with a luttle grinding of some plastic off the seat for extra clearance. Almost back in action.

@redsmith882010 5 ай бұрын

My other issue was the mounting bolts for the rack....I had to counter sink all but 1 so there was room for the amp to sit. So, unfortunately I couldn't assemble everything outside of the truck...had to install the board then the equipment.

@davidrendon9838 2 ай бұрын

Good info on the amp height. Looks like the Skar equivalent 1500 is 2.25 height. Should fit.

@hitemup85 8 ай бұрын

I have a 2014 Cadillac CTS with Bose would I still need an Amp- pro or Navtv if I’m installing a Audiocontrol DM 810

@IPvFletch 5 ай бұрын

did you have to trim rear seat back foam? or those foam surrounds which stick out along the sides? Thanks!

@thomasnew8606 Жыл бұрын

didnt show the actual subs or final look and sound???? The factory stereo can keep up with all of that sub power now?

@overtime0101pg 4 ай бұрын

Thanks for this video. It's well thought out. Question: can I use a PAC SNI-15 Preamp Adapter, PAC SNI-50A Line out converter, and PAC SNI-35 Variable LOC Line out converter to achieve the same as your LC2i PRO 2-Channel Line Output? BTW, I don't have the Bose Amp/Speakers @ProvoBeastAudio

@patjunick8965 3 ай бұрын

How do you put all that stuff behind the seat with all its foam? I just took my seat out to try and fit two self contained 8 inch JVC subs and they don't fit. One would directly in the middle, but the two don't.

@jesusmelendez1054 3 ай бұрын

Que ermoso travajo me encanto una chulada de jale viejon

@MrBamf00 5 ай бұрын

I have a 2018 Silverado with Bose can I use those same blue and green wires to provide a signal for my LCI2?

@engineered2 4 ай бұрын

How much foam trimming did you do on the back of the seat?

@parangutirimicuaro2 Ай бұрын

Hi great video I have a question or many, I am in the proses or planning to replace all the for speaker and add a subwoofer , I was planning to live everting the same way , I’m talking about the door speakers and tweeters. Until I saw your video , my question is can I bypass the boss amp or replace it all together and if yes HOW ?? Thank you. (3500hd Sierra - boss audio system)

@kadenhorrell9691 6 ай бұрын

I have a Silverado without bose , which wires do I tap into for mine

@dheasley2 5 ай бұрын

Skar says these 4 8" boxes can handle the evl and svx woofers. What do you guys think about that? Everyone don't seem to think so. I find it annoying that the 8",10", and 12" boxes that fit my truck are only compatible to the lower grade woofers unless i raise the back seat and i don't want to do that.

@GMCB-pu8pk 7 ай бұрын

How much does this set up cost with parts and labor? I want to do something similar in my truck

@Alex_MKE 4 ай бұрын

Why cant you connect to the stud of the battery terminal? Im having issues with either ground or power amps not turning on

@davidrendon9838 2 ай бұрын

I’m following this set up exactly. What size wires are the four 8’s using in the box? The wire kit you linked to use has 16 AWG. Is this correct to use?

@cjcallen5974 2 ай бұрын

are you able to pull your remote off of the bose amp wires if you are not using the lc2 in the video? and do you know which wire that would be?

@ProcessHF 2 ай бұрын

On the 2024s that nipple on the grommet does not exist. GM says to pass the wire through the plastic slit directly on the bottom of the grommet with a metal rod. It's a massive pain in the ass (specifically on the diesels)

@blackhornet25 3 ай бұрын

Is the lc2 or Lc7i pro needed if i have audiocontrol's dm-810 on a factory radio?

@johnamorrison82 7 ай бұрын

Awesome video! A lot of help for me while I'm installing my stereo. The only issue I had and I notice it for you too, the seat belt rubs the LC2i. Any ideas? I don't want to redo it all.

@ProvoBeastAudio 7 ай бұрын

For how often the seat belt won't be used, customer didn't care, and wanted it there.

@daverobertson1172 Ай бұрын

Can you do a amp install on a 24 Chevy Silverado crew cab without the bose system??? With all the parts you buy...

@ljpsr Жыл бұрын

Great video as usual!! I have a question. In a f150 I want to install a lc7i. Is there a harness in the back where I can pick up a signal without going up front to the radio? I'm also removing the pac ampro.

@ProvoBeastAudio Жыл бұрын

Hey there, thanks! Amp Pro connects that the radio, along with any T-harness on the market. The only instance where a harness is available in the rear would be trims with the Sony / B&O audio system from Ford where you can add the bypass harness at the factory amp in the rear. So the answer is a "yes, but...". Depends on your trim.

@OEFVETERAN 2 ай бұрын

Does the Bose amp still amplify the Bose speakers and the new amp the subwoofers only? Thanks! 🙏🏻

@kevindesson6730 4 ай бұрын

Would you happen to know the speakers wire colors for a 2023 yukon?

@julesbruchez-theartofgrapp9646 9 ай бұрын

Seems like a small power and ground wire for that type of draw

@firefox0915 3 ай бұрын

Did you remove that factory foam pieces off the rear of the seat so everything had room?

@yaboihuskymolly1159 4 ай бұрын

What is the thing you moved all the way to the right of the amp board?

@VWfanatic8 11 ай бұрын

How does that box sound?

@aaron44ornelas 5 ай бұрын

Do light dim ? Can it mess up electrical system ?

@TheTitansman1 Ай бұрын

Are the circuits you tapped into for subs only or could you run additional speakers off it?

@chrismuncey6023 2 ай бұрын

I used the same wires for signal with a jl 10 w7 an lc2i and a 1000 watt jl amp for some reason the signal from the sub out sounds terrible and the full range signal I can't get the jl amp to cut-off at 80 do I need a dedicated sub out?? Past the lc2i? Plz help!

@Digital7C4 11 ай бұрын

Where did you set your AccuBass Level and Threshold and Output Level? I have the same truck and and LC2i Pro as well and will be finishing my install soon. Thanks!

@ProvoBeastAudio 11 ай бұрын

Honestly, since it wasn't a personal truck, I can't remember. The LC2i pro instructions have a guide on walking you through the process of how to set that up properly.

@andyh8239 7 ай бұрын

In the process of installing a LC-6-1200 amung other things. Seems to me once the back seat goes back in the seat foam is going to blanket the amplifier quite tightly. (Not even sure the back rest sill even go back in with the amp mounted.) Did you have to cut the foam for this install? Any overheating issues? I drove a few miles without the rear seat and wow was that noisy. 10x louder than expected. If you do cut foam, does it increase cab noise much?

@-Primer- 7 ай бұрын

None of the channels show that, or the seat reinstalled. I have 3 amps on my custom rack and I had to do a lot of trimming and it still wont fit perfectly. The bottom of the seat is about 2 inches from going back into place. The "foam" on my 2024 GMC3500 PRO CREWCAB is not a soft foam, but more of a molded Styrofoam. Very dense, but cut well with a Oscillating Multi Tool.

@travispinkerton9916 11 ай бұрын

Hopefully you respond but I’m running do jl 13tw5v2-2 wired to 1 ohm and I’m running the line out converter but not the epicenter. Will the epicenter give me more bass? My lows hit very hard and my highs hit pretty good but think there could be room for improvement…

@gerardobernardino1092 10 ай бұрын

You need a bass knob for your amp. The epicenter is used to bring out the bass that's in music such as rock, Mexican, etc.

@Handwrench83 11 ай бұрын

23 sierra, factory signal sucks. Can't even turn my mb1024s up without the factory radio maxing out first. What do you recommend for the signal input so that it doesn't suck? Thos is a non bose stereo with an unknown line converter

@gerardobernardino1092 10 ай бұрын

LC7I with a custom harness from @Grayback1973

@gerardoreyes711 9 ай бұрын

Any idea if the set up will still work for two 10’s, or would you be able to explain what I’d have to do differently. Thanks

@Signatureofheaven 7 ай бұрын

The set up will work with 10 inch subs. Just make sure that you have the proper type of subs that will fit under your seat, recommended shallow subs, unless custom built enclosure, requires lifting the seat.

@andyh8239 7 ай бұрын

Did you lose the fader with this install method? I assume those are the rear speaker full range outputs, thus avoiding the need to (sum) the front highs and lows? I suppose this was for a sub install only, and no other drivers were amplified beyond the factory.

@markvveinotte1766 5 ай бұрын

He tapped the subwoofer wires so no it doesn’t affect the fader and there’s no full range signal cuz of the Bose amp

@ksigherrera 8 ай бұрын

Great Video! Question. Can that board be used on a Non-Bose truck? Their website doesn’t have a board for a non-Bose.

@Signatureofheaven 7 ай бұрын

The amp rack from the website will not work for non bose. They say there is foam behind the seat that doesn't allow the amp rack to fit properly. Fits perfect for Bose equipped trucks

@Chipum 10 ай бұрын

Awesome install very clean… just a quick question what is the price for everything in video installed? Thanks great channel

@ProvoBeastAudio 10 ай бұрын

Sure, we linked everything in the description for the current prices.

@naughtyca131970 11 ай бұрын

what is the ohm load of the bose for dash speakers? are they 3.5in size speakers and can i just get a aftermarket speaker and replace the dash speaker? thanks

@Signatureofheaven 7 ай бұрын

You can buy aftermarket speakers and drop in if they are the same size. The bose amplifier will still amplify the sound, which in turn will make them sound good. The speakers are 2.5" in the dash.

@arturoltx4059 Ай бұрын

Why instead of tapping the wires, why didn’t you use the plug and play T harness for the Bose amp connector??? 🤔

@darrylm7588 6 ай бұрын

Where is the factory sub in the new GM trucks? I just pick up a 2024 AT4 1500. Is there more of a simple solution for the sub amp? I have an older Audison LRx 1.1k mono block with high level inputs, could I not just use the signal from the Bose amp and go directly into the Audison?

@jcook8191 3 ай бұрын

Not sure on the 24 models but my 21 model has the Bose sub in the console

@mikeganard6751 Жыл бұрын

Looks great! I have a LC7i I’m looking to install. Can I get power and ground off my distribution block instead of the amp? Also would I need a fuse for the LC7i?

@JasonWW2000 11 ай бұрын

Yes, you can get power and ground from there. Add a small 2A inline fuse on the power wire going to the LC7I.

@mikeganard6751 11 ай бұрын

@@JasonWW2000 ok thank you!

@armandojimenez3596 5 ай бұрын

Hi I have a sound system but the subs are not working and the sound system is turn on

@tyroneferrell1602 5 ай бұрын

Nice work where are you located??

@dsgaragedavid1987 9 ай бұрын

I’m using the lc6 and I have the Bose system I’m not getting a signal from the rear speakers any advice

@Signatureofheaven 7 ай бұрын

Use the signal from the front, yellow/Yellow & Black

@kenacyt 11 ай бұрын

What signal is that on the plug that you tapped into? The GM accessory Kicker sub shows using a yellow & yellow/black pair near the passenger front kick panel, is this a better spot to pull the signal from?

@ProvoBeastAudio 11 ай бұрын

It's the Bose subwoofer wiring connection at the Bose amp. It's right there instead of running the wiring to the bose subwoofer in the center console.

@gyfhj 7 ай бұрын

Do you have a part number for the harness you’re using to tap into the sub wires?

@sebastianmartin3424 11 ай бұрын

Are your 4 8” subs 2 or 4 ohm? I’m curious to see how you wired them to get 1 ohm final impedance?

@Half_Gassed 8 ай бұрын

He literally said dvc 2ohm load skars, and then shows the wiring diagram as to how they wired them down..... it's like you didn't even watch the video 🤔

@MerleHaggler Ай бұрын

No issues with the ANC?

@growitwemowitllc1752 10 ай бұрын

When I go to the site for amp rack it says won’t work for mine cause I don’t have the Bose. Seem odds since the only difference is the amp in the back and I don’t have that? Would it still work?

@gerardobernardino1092 10 ай бұрын

The only reason why it says it won't work is because your truck(like mine) has foam behind the seat. And because we have less mounting studs.

@growitwemowitllc1752 10 ай бұрын

@@gerardobernardino1092 so it will some what work? I moved the foam from mine

@gerardobernardino1092 10 ай бұрын

@growitwemowitllc1752 it'll work no problem just add extra mounting brackets.

@ejy99 9 ай бұрын

Great video and very clean install. I have question that you may be able to answer so I can get my install done right. First, I have not taken the backseat off, so I cannot confirm I have the same amps in the back, but I assume so since I DO have the Bose system in my 2021 TB. I am doing a very simple install. A kicker pre-fab box, an Alpine mono amp, and a Kicker LOC. The LOC has the 12v turn-on lead coming off of it. Models below for reference. My question is, in your install you tapped into the Bose amp with the white and grey speaker leads from the blue and green wires in the harness. In every other video I have seen, people are using the yellow/yellow and black wire into a LOC to go to the mono Amp, usually in the front passenger kick panel. Is there a reason you did this? Is it because you need a full-range signal to go into the LC2? If I can get to the yellow/yellow & black wires right there in the rear near the harness, I don’t see a reason to put the LOC in the front passenger Kick panel like I have seen most do. What signal comes from the yellow/yellow & black wires? For my simple setup, what is my best course of action? Thanks for the recommendation! Kicker TRTP 10” Sub Box Alpine S-A60M Mono Amp Kicker 46KISLOC2 Speaker wire to RCA LOC

@johnspratley6691 9 ай бұрын

Same here as far as the Bose output wire. I have been trying to find a video of someone coming from the Bose subwoofer. Stumbled one would go to the door speakers, carrying the highs, when there is a input from a sub, carrying the lows. Wouldn’t the door speakers give out the wrong signals, especially when adjusting the settings on the head unit? Im sure the LC2 will make up for that but it’s probably going to have some sort of interference when adjusting on the head unit.

@ejy99 9 ай бұрын

@@johnspratley6691 I think after seeing so many videos on YT that say to use the yellow/yellow&black that is what I am going to just do and see how it works out. I am going to trace them back to where they end behind the seat versus running my LOC all the way up to the kick panel. That just doesn't make sense to me. The Amp should be able to take the full range signal, if that is what is coming through those wires (Y/Y&B), and just pull the lows using the low pass filter, at least as I understand it. I have used LOCs with full range signal before and it works fine. Ill come back on here and let you know how it goes. Thanks for the reply.

@Frankd1277 4 ай бұрын

Did you find the yellow and black wires near the amp? I currently am in the middle of a subwoofer install and can't figure out what wires to connect to the loc.

@Signatureofheaven 2 ай бұрын

You can use the signal from the bose amp yellow/yellow&black wires to make your connections easy. You can use the Audiocontrol LC2I Pro or the Pac Audio SNI-35. If all you're doing is adding a subwoofer amp, get the signal from the rear. You just have to remove the seat.

@bnastystuntz Ай бұрын

How would i just run the rca to the amp from the lc2i without that epicenter module. Would i go strait to where the rca out goes from.the epicenter module?

@ProvoBeastAudio Ай бұрын

without an epicenter, just LC2i output right to the amp input.

@angelrios6624 5 күн бұрын

Approx how much is that work with labor and parts ?

@jamessmart7605 10 ай бұрын

Could 0/1 gauge wire fit through that grommet in the fire wall

@gerardobernardino1092 10 ай бұрын

Yes, it will. I have 2/0 running through mine.

@franciscoovilla1666 3 ай бұрын

I have the same install with an audiocontrol lc2i. And epicenter. But im getting a thump sound when theres no music playing Any advice???

@Signatureofheaven 2 ай бұрын

A thump sound? When you turn on/off the system? While you're driving?

@user-el6ul7lk2d 2 ай бұрын

Does the epicenter get power and ground from the bass amp or can you get it from the lc2??? Thanks

@ProvoBeastAudio 2 ай бұрын

Both the LC2i and Epicenter need constant 12v and ground, which we snagged both from the power and ground terminals of the amplifier.

@bnastystuntz Ай бұрын

What signal wire did you use when tapping into the bose amplifier? Im assuming you tapped i to the subwoofer signal. Will doing it this way prevent the chimes bei g obnoxiously loud? Also i didn't see and noise cancelation bypass?

@ProvoBeastAudio Ай бұрын

No ANC found on this gen truck in this trim, and the blue / green wires shown we tapped into are the sub signal only which doesn't have any chime signal passing through it.

@bnastystuntz Ай бұрын

@ProvoBeastAudio thank you..

@jeffcaldwell3349 13 күн бұрын

How much would an install like this cost?

@robm5974 6 ай бұрын

Nice craftsmanship. Question on the overall system. It seems like 1800W would be a bit overkill putting it up against factory door speakers & amp? How did it sound overall? To me the factory Bose system lacks on the mid/high range already, did the subs drown it out?

@ProvoBeastAudio 6 ай бұрын

It's what the customer wanted. Yeah, it's tons of bass, but I recommend a more rounded system, just depends on your trim and budget. If you want more direction, send me a message on facebook or instagram.

@robm5974 6 ай бұрын

@@ProvoBeastAudio good deal, thanks for the quick reply!

@ivankorth4458 4 ай бұрын

How much for an install like this

@404spaz 5 ай бұрын

How would this affect door chimes on a non Bose amp silverado

@ProvoBeastAudio 5 ай бұрын

Non-Bose means there isn't an external amplifier in most cases. The radio powers the speakers internally. If you have that setup, all you need is the GM Radio T harness and line out converter we have linked in the description. Factory radio module is behind the glove box.

@user-zo4bw2dy2x Жыл бұрын

I have a 2022 chevy silverado non bose refresh interior would Iike to add a 4 channel amplifier for the doors without the t harness because I have th e black and gray plugs and can't find that harness anywhere.

@ProvoBeastAudio Жыл бұрын

Hey Happy to help. Send us a message on our facebook or instagram pages and we can help find a harness that would work for you.

@gerardobernardino1092 10 ай бұрын

John can custom make your harness @Grayback1973

@kelaro75 9 ай бұрын

I got with John for a integration harness for my 2024. He responded promptly and asked for specific info and now I'm just patiently waiting for my harness.

@poloturrubiartes7622 11 ай бұрын

I have a 2020 Chevy custom trail boss without Bose. I looked up the amp rack with the link and the website said it was not compatible to my truck. In your opinion could I use the amp rack that you used or will I have to find a different rack?

@ProvoBeastAudio 11 ай бұрын

I'd reach out to sounds good stereo to see if they have a solution for your truck.

@djcarkhuff 10 ай бұрын

It'll physically fit in your truck, but not all the mounting studs may be present to secure it to the back cab wall is all.

@Signatureofheaven 7 ай бұрын

You'll need to cut out the foam and add mounting brackets to get it to hold

@anthony03241980 8 ай бұрын

Got I huge question lol what wires did you tap into on the Bose bec I’m doing a 23 with the Bose I’m just wondering what wires you used and if you had any problems I will wait till you respond before I tap into anything

@ProvoBeastAudio 8 ай бұрын

just the factory sub speaker wiring (blue and green twisted pair at the amp). That is the only factory connection.

@gyfhj 7 ай бұрын

Is there a harness for this?

@anthony03241980 7 ай бұрын

Do you happen to know what wires are what back at the amp on the Bose amp so if I do door speakers

@djcarkhuff 10 ай бұрын

How thick is everything in relation to the seat back? How much of the foam had to be trimmed?

@ProvoBeastAudio 10 ай бұрын

We didn't have to trim any foam, and still had decent air flow. If you have a taller setup, or an amp that runs hot, then trimming is recommended.

@djcarkhuff 10 ай бұрын

@@ProvoBeastAudioThanks for the reply. I'm attempting to install a relatively simple setup, a pair of Kicker hideaways. They're about 3 inches thick, so that's why I was curious about the foam trimming. Thanks for the heads up.

@andyh8239 7 ай бұрын

Did any of the foam on the seat back-rest need to be trimmed for this setup? Does the foam press up tight to the equipment / compressed?

@-Primer- 7 ай бұрын

@andyh8239 7 ай бұрын

@@-Primer- I ended up 3D printing custom brackets with brass threaded inserts. Exoxied the brackets into place and the equipment is removable. I only had to trim on small piece of foam, but stuff does seem to squeeeze tight a bit on re-installation lf the seat. I purchased a 3D scanner so I can model it better for the sub integration which is next on the list of things to do.

@-Primer- 7 ай бұрын

@@andyh8239 Well that's clever. I'm pretty well versed with Fusion 360 and/but my printer is only 230x230. The idea of printing brackets to get the amps to sit "deeper" has got my gears turning. I guess that's a new project to work on --- DAMMIT !

@andyh8239 7 ай бұрын

@@-Primer- I used a profile gauge when I made them and they worked great but the 3D scanner thats on the way should be a game changer as you can mock it all up virtually and obtain perfect profiles. Could even scan the back of the seat foam to identify what needs to be cut. I designed a holder that clamps to a capacitor which fit perfectly behind the seatbelt strap (cap locks into place with set screws and leaves behind only a thin bracket when removed. I was even able to print connectors to adapt the tweeters to the factory dash harness. I made a mockup of the tweeters I wanted to ensure they would fit (Morel 728's) as the ScanSpeak ones I planned to use had too large of magnets. I'd like to scan the doors next to see if I could put some ScanSpeak Revelator 8's in the doors. Madisound has a lot of good stuff to choose from.

@davidrendon9838 2 ай бұрын

What’s the Skar equivalent amp…for this set up? Thanks. Great video!

@ProvoBeastAudio 2 ай бұрын

With those specific subs, the RP-1500.1D

@davidrendon9838 2 ай бұрын

@@ProvoBeastAudio ok thanks!

@bmanslayer94 8 ай бұрын

I got a 2024 silverado with bose pre installed and for the rubber grommet near battery terminal it doesn't have the accessory plug for me to feed through for positive. Any ideas?

@Signatureofheaven 7 ай бұрын

Check both sides of the truck under hood. Should have one on either or both sides

@kelaro75 7 ай бұрын

My 2024 didn't have a nipple. I just slit the big grommet on the passenger side.

@Signatureofheaven 7 ай бұрын

Good deal, good to know. Thanks!

@mrpanchito9215 9 ай бұрын

Did you have any problems with the noise canceling?

@ProvoBeastAudio 9 ай бұрын

This gen Silverado wasn’t equipped with anc.

@twomontess 8 ай бұрын

Why did you grab signal from front ? Why not the sub signal wire ? (The two Yellow wires) Now when he lowers the bass the sub goes away and when he fades or balance left to right the subs have no signal !? Second epicenter is not needed. Looks like a case of over sell to me.

@ProvoBeastAudio 8 ай бұрын

Did you not watch all the video? (Apparently not). We tapped into the Boss sub output for signal, not the fronts. Secondly, the epicenter was provided by the customer as he wanted it installed. We didn’t sell him any of this equipment as it was all provided by the owner of the truck. This truck went through two other shops before it made it to use to fix and make right.

@juliosandoval8244 6 ай бұрын

Why do you need a lc2i and a epicenter?the lc2i has the same function expect its a high n low adapter with bass enhancement plug in bass knob also

@ProvoBeastAudio 6 ай бұрын

LC2i doesn’t have any eq capabilities, just a line driver and bass roll off correction. The epicenter has a line driver function as well, but also eq function. If you want an (almost) all in one, check out the epicenter pro.

@juliosandoval8244 6 ай бұрын

@@ProvoBeastAudio I've installed the epicenter pro couple times.

@drawsawyer5881 9 ай бұрын

Started a complete audio upgrade in a ‘22 this weekend. Did you have to cut foam out of the back of the seat to get it back in. There’s no way I could mount that board and move everything around without doing so.

@zachschmidt2802 8 ай бұрын

Did you figure this out just ran into the same problem

@drawsawyer5881 8 ай бұрын

@@zachschmidt2802 I got a 2000w amp behind it. Had to cut a significant amount of foam off the seat. I did it in a way that the amp is contained in one of those areas that lead to the cab vent. Closed off the other cab vent. Theory is it’s going to push all cabin air/pressure out the vent with the amp right beside it and cool it. You couldn’t mount that board without taking all of the foam off the seat. I would definitely put some sound deadening on that back wall too. For me, the real downside is not being able to access the amp without unbolting the seat.

@drawsawyer5881 8 ай бұрын

Also moved factory equipment that was back there to behind the box under rear seat. Not as clean as this install, but it’s clean enough for adding an LC2i and mids/highs amp under the passenger seat, four eights under rear seat, and 2kamp behind the seat. No wires showing. GM does kind of make hiding wires easy with their huge channels down the side. Now if they’d just unlock my ECM…

@Signatureofheaven 7 ай бұрын

The amp board is made for trucks with the Bose system.

@frankparisi2433 8 ай бұрын

Really good video. Why not use an Epicenter Micro. One device does it all?

@ProvoBeastAudio 8 ай бұрын

Customer provided epicenter before the install. The Micro is indeed a better choice to save space, but since it was already purchased, we used what we had.

@frankparisi2433 8 ай бұрын

@ProvoBeastAudio I ordered an Epicenter. A little pricey but a nice toy.

@ayeayeronsearcy9402 9 ай бұрын

I followed your setup. I have the 23 silverado with bose. When I unlock the doors the amp comes on? What could be the cause of this? I'm assuming its the remote wire but just curious how to set it up to where it doesn't turn on til the truck is on

@Signatureofheaven 7 ай бұрын

You will need to change the way the LC2I comes on. You'd have to set it to Audio, or you'll have to run a remote wire to your fuse box.

@franciscoovilla1666 3 ай бұрын

Im having the same issue. When unlocking the truck all my system comes on. And sometimes im getting the thump sound of the subwoofers when theres no music playing Any advice??

@ayeayeronsearcy9402 2 ай бұрын

@franciscoovilla1666 same here. Been looking for a fix.

@davidrendon9838 2 ай бұрын

What did you end up doing?

@Signatureofheaven 2 ай бұрын

Depending on the LOC you're using... You will need to change the way the LOC comes on. You'd have to run a remote wire to a fuse in your fuse box that only comes on when the truck's ignition comes on and turns off. Sometimes the USB charger will work, or another accessory type fuse.

@jayh7423 2 ай бұрын

Hahaha please show us how you modified the rear seat in order to get it back on!!!

@AhmedAddas 8 ай бұрын

Why did you keep using oem bose amp?

@jcook8191 3 ай бұрын

Looks like The amp is still being used for factory Bose speakers and the Bose sub.

@traycain9372 9 ай бұрын

Do you have to modify the seat any?

@ayeayeronsearcy9402 9 ай бұрын

Just had to take the foam off the back

@user-je3iz9qf8i 10 ай бұрын

Not gonna sound matt the rear wall of the truck?(Behind the Amp Rack). Might as well since you have everything out. 8)

@civstu 9 ай бұрын

Are you able to reinstall the rear seat back or are you permanently leaving it off?

@Signatureofheaven 7 ай бұрын

The back seat goes right back on.

@jayh7423 2 ай бұрын

Ahahahahhahahahahhaaa No. It cannot. You have to cut the hell out of the foam.

@cmwilliams357 9 ай бұрын

Hello sir, Is there a amp rack for a larger amp for this truck?

@ProvoBeastAudio 9 ай бұрын

Check out sounds good stereo to find the one that fits your needs.

@cmwilliams357 9 ай бұрын

Thank you sir 💝

@Jdawg-hn5pd 3 ай бұрын

What’s the total for all this

@iwiredit 9 ай бұрын

Kicker 1800 watts @ 1 ohm means about 800 or 900 watts rms.

@ProvoBeastAudio 9 ай бұрын

Kicker puts the RMS wattage on their amps, not Peak power, sorry. This is indeed 1800 + watts @ 1 ohm per the birth sheet included with the amp.

@iwiredit 9 ай бұрын

@@ProvoBeastAudio Its good Kicker has changed and went back to there old roots. After they stopped the ZR series it seemed all there stuff was over seas and over rated power the quality went down hill in the mid 2000's But seems they revamped. So good on them.

@anthonyrosati8707 5 ай бұрын

Clean like ya nanas living room son

@davidhernandez-tc7ko 4 ай бұрын

Yo... send me a link for the Amp panel, that looks clean!!

@joshwright9257 2 ай бұрын

It's in the comments

@gyfhj 7 ай бұрын

Hey awesome video man! What are the dimensions of the amp rack?

@brockd13 6 ай бұрын

14.5 x 44.5 I just copied/built my own in an hour and saved $185

@gyfhj 6 ай бұрын

Me too! 💪🏼

@jonatana8531 7 ай бұрын

How could I add a 4 channel amp to the Bose? I have a 22 1500 ltz with Bose

@ProvoBeastAudio 7 ай бұрын

There isn't an AmpPro module yet to replace the OEM bose amp, so you will have to tap in for signal after the amp. There are Pac T harness available to help you do that, but you'll need some sort of high power LOC and such to accomplish this for internal summing, etc.

@jonatana8531 7 ай бұрын

@@ProvoBeastAudio I have a loc on a sub right now tapped into the speakers. I want to add a 4 channel so would I just cut the front and rear speaker wires into a lc5i and replace my loc from the sub into the lc5i then run my own wires door to door into the speakers? My speakers are also upgraded to Focal speakers. Cutting my harness isn’t my issue I can do that with no issue, I just know not to cut the front tweeters since that’s for phone calls etc..

@ProvoBeastAudio 7 ай бұрын

No need for cutting harnesses, there is a T harness you can use. Yes, reroute all into the LC5i or lC6i where you can do internal summing for your amplifiers.. amzn.to/48fWiZy@@jonatana8531