I literally installed following every step and I made my control go crazy
@CraigsChannel Жыл бұрын
Finally the videos up 😁 my messages for the past 2 weeks are "When's the BDM-030 video coming?" 😄
@jenskarl3341 Жыл бұрын
if i get the rise 4 kit with 4 paddels can i use this video and not going to use l3 or r3 and pad?
@CraigsChannel Жыл бұрын
@@jenskarl3341 yeah it's pretty much the same setup. Just skip the taking out of the trackpad and soldering if you don't want L3 or R3. I don't use them either
@jenskarl3341 Жыл бұрын
@@CraigsChannel thanks!
@ExtremeRate Жыл бұрын
Yea finally bro 😁
@josearturozaunruiz1113 Жыл бұрын
How can I do it without soldering?
@HateBeinAlive Жыл бұрын
Heart stopped a second thought you guys had already found a way to add 4 paddles to the EDGE
@ExtremeRate Жыл бұрын
Bro don't you think it's too soon for it lol
@RYVENANT Жыл бұрын
Doesn't the edge have paddles already?
@aegiswing Жыл бұрын
@@RYVENANT never. enough. buttons.
@MADDOWG22 Жыл бұрын
No way i watched your old vid on your channel and was hype to see you're now on the official channel. good shit dude ur guides are awesome
@princegray32269 ай бұрын
I can confirm if you have bdm 040 it will work with this version!
@isquig8 ай бұрын
I was wondering I just got a new controller thanks doggy
@BwinSZN Жыл бұрын
can you please make a separate, shorter video of installation without mapping the touchpad and other parts, I find this confusing even with skipping the time stamps
@kwoni3337 Жыл бұрын
Yea all these videos say "skip ahead" if you're not doing the touchpad, but you skip ahead and it's missed about 5 necessary steps that were part of the touch pad section. Feels like nobody actually proof read/watched the video without context
@fredredd41010 ай бұрын
yes these videos are utter trash
@famezy91039 ай бұрын
Just in case you still haven’t done this, you need to watch the videos for older version PS5 controllers BDM 010 and BDM 020
@TheGameOverBoys9 ай бұрын
@@famezy9103do those videos work for the bdm 030 tho?
@famezy91039 ай бұрын
@@TheGameOverBoys The kit for BDM 030 is the same as BDM 010 and 020, but for the BDM 030 you have to solder the cables provided in the kit in order for it work. You don’t need to solder for the older BDM 010 and 020 unless you want to remap the L and R sticks
@Antoine..10 ай бұрын
After 3 hours, i finally did it 🍾 without L3, R3 and pad because i only need X and O
@derickxo9 ай бұрын
Out of curiosity, did you solder them? Because I really don't need the TouchPad or the L3 and R3 buttons
@xxsatxx8 ай бұрын
@@derickxo same
@Cjohnson54496 ай бұрын
@@derickxoyou don’t need to solder if you are not using touchpad or R3,L3
@BaneIsAlive Жыл бұрын
Thanks for these paddles. I have 4 of these funny enough. I was thinking when would we get back buttons for the PS5 controller ? The paddles are good but they do feel like an extension on the PS5 controller. I feel if we could get back buttons which are not too extensive ( like the ps4 ones ) but sit a little deep into the shell of the controller with the intention of it being part of the controller will be great. A membrane style back button like the face buttons of the PS4 controller will be something new to the community.
@CraigsChannel Жыл бұрын
I wouldn't mind trying buttons, but think I'm that used to paddles now they might feel weird! Guess it would be nice to have a choice as I've no idea what percentage of people prefer paddles and others who prefer buttons. Them new half dome button on the Edge seem interesting
@BaneIsAlive Жыл бұрын
@@CraigsChannel yeah the paddles are nice but when I swap to my default PS5 controller I realise how much space the RISE4 takes. Trying something different like the buttons will be nice but I understand the rumbles get in the way when trying to do something in the handles.
@ExtremeRate Жыл бұрын
@@BaneIsAlive We are working on the new kit and it's the buttons style! But as you said there is not much space inside so a membrane style is a challenge!
@ExtremeRate Жыл бұрын
@@CraigsChannel Half dome back buttons?
@NapkinsMD Жыл бұрын
Soldering is turning me off from purchasing this & the English “if you don’t need ___ button can be mapped to rear button” is so confusing. I just want to be able to press x on a paddle without soldering. If I just plug ribbons in will I be fine with it still working?
@CraigsChannel Жыл бұрын
No need for soldering if you only wany X and O
@chrisphillips11148 ай бұрын
Works great. I even broke one of the original ribbon cables off and still works. Was probably just for reset
@-DeScruff Жыл бұрын
I think a tip I would give to help with aligning the yellow ribbon with the motherboard, is to use the screw driver (or similar small rod that can fit through the holes) as a pin to temporarily help align the thing.
@shamasmahroof8054 Жыл бұрын
Hey. When you installed the do u also complete the fpc part if ur not programming L3 or touchpad?
@-DeScruff Жыл бұрын
@@shamasmahroof8054 What do you mean? If you are asking if you need to attach the wire/ribbon even if you are not going to use the kit for L3/R3/Touchpad. Then the answer is no. If you are not going to bind L3/R3/Touchpad you can skip soldering, or attaching the L3/R3 ribbon to the main ribbon cable
@shamasmahroof8054 Жыл бұрын
@DeScruff at the 10:10 minute mark if u could look at that please where he puts the Eva tape on. Is that part also necessary if not using touchpad or L3?
@-DeScruff Жыл бұрын
@@shamasmahroof8054 So I am not 100% sure if it is necessary at all. Its meant to help apply more pressure on the ribbons for better contact. If you have the tape might as well do it.
@shamasmahroof8054 Жыл бұрын
@@-DeScruff thanks alot mate
@iJulioRocha11 ай бұрын
This was the most incredible tutorial I've ever followed. Thank you so so much for this complex yet so simple tutorial
@sawek7669 Жыл бұрын
Please make rise 4 kit and click triggers for Dualsense edge. it will be perfect pad.
@ExtremeRate Жыл бұрын
We will try!
@user-oe8oe8rg1j11 ай бұрын
Thanks mate my controller is ruined I can't play on my ps5 anymore
@Desilv Жыл бұрын
Would be huge if you make a 4 paddle edge controller with clicky triggers.. maybe exactly the same paddles as the edge has but then two more 😳😳
@ExtremeRate Жыл бұрын
We will try bro, but frankly it's really hard
@RyoAdR Жыл бұрын
@@ExtremeRate can I paste Two PF Rise FPC cables with the contacts on the motherboard ? I have a PF Rise for extremerate paddles and another that I found for clicky triggers.
@damiankowalczyk94056 ай бұрын
if the light flashes three times , it indicates there is a problem with installation. How can i fix it ? Pls help
@Yugo5300 Жыл бұрын
Thx Einstein for making me close the hole damn thing before noticing that no light is burning on the kit
@ExtremeRate Жыл бұрын
So have you fixed the issue?
@Yugo5300 Жыл бұрын
@@ExtremeRate yes, it seems the light button isn’t visible like it is on other controllers i customised with your backbuttons.. although my mic isn’t working (can’t hear people, they hear me) but I don’t bother opening it up again because everything works fine with a headset on 👍🏻
@ImagineMeTrying Жыл бұрын
What do I do if I don’t have a soldering iron
@CraigsChannel Жыл бұрын
You only need to solder 'if' you want to remap L3/R3 or the trackpad, most people only use the symbol buttons
@hybrid11theory756 ай бұрын
Nice kit. Installation was easy with such an in-depth guide. I don't like alu pedals, u constantly get electro shocks from these while gaming... lol
@garrettst99220 күн бұрын
Worked for about two months.
@Adub_69 ай бұрын
Can someone please confirm that if you don’t want to remap L3, R3 or touch pad that you don’t need to solder anything? I’ve installed the bdm-020 before which didn’t but it’s not really clarified in the video
@Bsidesthepoint7 ай бұрын
I fucking agree with you bro. screw this guy for not saying that in audible words. lol, It's a great video well explained if you want to map the touchpad and the R3 L3 buttons. I ended up ruining a ribbon cable and bought a new one. I watched this video again and realized I didn't have to do any of this trickery if you ARE ONLY GOING TO RE MAP THE SQAURE, TRIANGLE, X AND CIRCLE buttons.
@rfG1112 Жыл бұрын
What's the purpose of installing the EVA tape under the original fpc board? Also can't you just put the remap fpc board on top the original like normal? Similar to the BDM 020 installation of the remap fpc board.
@shamasmahroof8054 Жыл бұрын
Did u manage to find out if that step is necessary as I'm going to be installing my kit soon just need to figure out if that step is necessary?
@rfG1112 Жыл бұрын
@@shamasmahroof8054 Nope. But I installed it without and no problems.
@gavgoodbye2yesterday91011 ай бұрын
Is this kit the same one that fits the BDM010 & 020 too? I bought a kit ages ago and it seems to have all of the came bits but my controller died and I only have a newer BDM030 now - will it still work? Help lol
@RodsDadBod Жыл бұрын
Ive had my back buttons on for about a month now and theyve been good. But today i noticed theyre not reacting as much even though the click of the paddle sounds fine. I have one set to jump the other to interact/reload and theyre both kinda not reacting properly.
@mav144fps7 ай бұрын
do you have to have a soldering iron
@TheGrichka10 ай бұрын
it is necessary with the welding device... if you don't have it the kit is useless i think
@vince910810 ай бұрын
Just a question, is BDM 020 and 030 has the same installation method? I don't do the touchpad or L3 or R3 just straight to the X, square, circle button
@nathanmaxwell842 Жыл бұрын
After installation my controller will not turn on. It will light up orange when connected to a usb C cable but that’s all the response I get. I took it apart a few times to make sure the batter was connected correctly and I have also tried making sure the button sensor pad was flesh and free of dust. Nothing has worked. Please help!!!!
@tcm246410 ай бұрын
This happened to me too!!! Did you find a fix???
@trevv4329 Жыл бұрын
I have an 020 kit with a 030 controller… i did that same thing 2 years ago when i bought a 010 kit for an 020 controller. Why is sony doing this? Do they know about your product or something? How am i supposed to know a controller is 020 nowadays?
@ExtremeRate Жыл бұрын
lol In fact, they did it for cost down of the controller, as you can see the 030 structure is more simple than 010 and 020, less components, they can save lots of cost.
@nickjacobsss Жыл бұрын
Hyped! When are the bdm030 trigger switches coming out?
@ExtremeRate Жыл бұрын
In about a month, please stay tuned!
@nickjacobsss Жыл бұрын
@@ExtremeRate awesome! Thanks
@user-dl4tr3jm5b7 ай бұрын
Hello, I need help, I cut the wrong part in my quite and I would like a new piece for bdm 40 please (i am french)
@josearturozaunruiz1113 Жыл бұрын
On the exact minute 12:30, it fits perfect in your controller. But in mine it doesn’t! The holes are more separate in my controller
@MisfitsGuideToTheGalaxy Жыл бұрын
U sure u bought the correct model kit?
@DylanMcGuire-ij4fc Жыл бұрын
Mine is the same Jose, the holes don’t match up. I’m using the bdm 030 bits too!
@user-gr7no6lf8q Жыл бұрын
Is the tape you put on necessary or can I just put it straight on
@user-gr7no6lf8q Жыл бұрын
@CraigsChannel
@eddierodriguez1246 Жыл бұрын
LETS GOO I DID MY 030 KIT PERFECT WITH NO VIDEO !! SHOUTOUT CRAIGS CHANNEL FOR THE OTHER VIDS ANS EXPLANATIONS
@CraigsChannel Жыл бұрын
Thanks man 😁
@ZAZUtakiyaho Жыл бұрын
@@CraigsChannel I don’t see a bdm 030 on your channel and how can you tell it’s Bdm 030
@CraigsChannel Жыл бұрын
@Takiyaho I've not yet had a BDM-030, been looking for one in case I need to do anything on one bit none have popped up. If you press L2 or R2 you can look inside the button and tell which version it is from that. The 030 has a tiny little spring visible
@ZAZUtakiyaho Жыл бұрын
@@CraigsChannel yeah I have a bdm 030 I also checked on Amazon I saw one
@maximvandervelden791310 ай бұрын
I've never open up an controller in my life. Do you guys recommend me juts following the tutorial or should I let someone with a bit more experience do it?
@dominiccramp9 ай бұрын
This was helpful and clearly laid out but ya do move at speed. For us fat fingered folk dealing with an iPad that you have to scroll back over and over again and then you go far back and then too far forward....well a little walk to clear the head saved the early death of the iPad😊 Great product though. Thanks! UPDATE: A testament to the build quality....put it all back together and realized I forgot to put the Option and screen capture buttons in so had to reverse engineer it which was a major hassle. The speaker button fell off and couldn't get it back on but not a great loss. The little piece attached to the mic cable also fell off but again, not a big deal for me. Put it all back again, didn't work! Had a feeling I forgot to plug the battery in so went back in again, yup dum dum. Put it all back together AGAIN and now works solid. Great little product and all the parts and cables took the back and forth without a problem. One thing though if you have big hands just breathe deep. You'll get there but it is very finicky. And not your fault at all but the parts and screw driver look much bigger in your hands than in reality but probably because of the zoom.
@markwarren35909 ай бұрын
I just installed the clicky trigger kit and rise 2.0 for the bdm 30 and didnt get a red light spent hours taking it apart and in the end it was the fpc cable not lining up with the mother board . Was about ready to launch it out the window but it's working a treat now 😂
@voltage56148 ай бұрын
I had the same problem. I didn’t put the EVA tape on. Hopefully that’ll fix my problem when I work on it tonight
@jriveraa08 ай бұрын
having the same problem, any solution?@@voltage5614
@brendoneggers5673 Жыл бұрын
Waiting patiently for the front shells to be realised, do you know when they'll be available?
@ExtremeRate Жыл бұрын
Please wait for a couple of weeks!
@Gspanked5150 Жыл бұрын
So no need for soldering if you just want to remap the front buttons x, circle, square, triangle?
@RodsDadBod Жыл бұрын
That's what I'm wondering. This one looks much simpler compared to the BDM-010 and 020 if that's the case. If it's really just sticking a ribbon in.
@ExtremeRate Жыл бұрын
Just skip the soldering process in the video, every other buttons still works
@ExtremeRate Жыл бұрын
Just skip the soldering process in the video
@tychodellink5315 Жыл бұрын
Waiting for the clicky triggers for BDM-030 to release, can you tell me anything about a sooon release date maybe? :)
@CraigsChannel Жыл бұрын
I think it's going to be one of them one that you'll just have to watch this space... hopefully any time now
@NoScope47696 ай бұрын
Do you have to have the soldering iron for this?
@howitzer55586 ай бұрын
You do if you want the touch pad or R3 and L3 to be mapped. If you don’t, you don’t have to solder at all
@kerim_og_9378 Жыл бұрын
as soon as i connect the orange remap cable, my d pad and L2 & L1 arent working, without the cable, everything is working, whats wrong with this kit ? i reinstalled it 3x. there were no problems with the bdm 020 kit tho EDIT: i repositioned the EVA tape (and probably the remap cable too again) and now everything is working !
@dharma9404 Жыл бұрын
@ExtremeRate are you working on a BDM 030 hair trigger kit?
@ExtremeRate Жыл бұрын
We are working on it, please stay tuned!
@LuisMartinez-si4dg7 ай бұрын
@@ExtremeRate The light keeps turning on by itself after I mapped the buttons. When the light is on it does not work. Any solution ?
@TurgutYildirim1955 Жыл бұрын
Ich habe das selbe gemacht was du gemacht hast und bei mir läuft das nicht. Ok hab nochmal ausgebaut. Hab bemerkt das die eine flexkabel nich richtig drin war. Jetzt klappt das
@Intjmate8 ай бұрын
I lined up and put EVA tape under the original FPC cable and the yellow one wouldn’t go on top of it, I tried doing it as you have in the video and sticking it to the mother board and it stuck but when I go to put my motherboard back in, it won’t click on the right side (the side where the Added EVA tape and FPC cable is, it just won’t click in. What do I Do.
@boefje197611 ай бұрын
I installed the kits on my 2 controllers,after approxemately 1 week playing with both controllers i suddenly have stickdrift on the right analog stick,on both controllers at the same day!How can i try a reset?What can be the problem,i know there was an update of sony for the dualsense?I cannot reach the reset button on the back due the risekit..Hopefully you have an idea to reset or solution for the issue,thank you in advance.The risekit works perfectly and i soldered for all buttons
@m_robb0 Жыл бұрын
On the front cable, one of the holes are covered up. There isn’t two holes, only one.
@brick66117 ай бұрын
The track pad is not coming out
@LuisMartinez-si4dg7 ай бұрын
The light keeps turning on by itself after I mapped the buttons. When the light is on it does not work. Any solution ?
@FreshaThen Жыл бұрын
Mine didn't come with metal rods smh. I checked every bag 5 times and all over my desk.. nothing
@diegoo456 ай бұрын
If I don’t need touch pad or r3 L3 do I just skip everything ? Plug and play, kind of lost
@thekingcovey85629 ай бұрын
I have a BDM-030 motherboard and I bought the right kit but it doesn’t work and everything is connected properly…
@excusemerl7766 Жыл бұрын
Wow good video! I have a question my controller pad is bdm010 makes it a difference or is everything like in ur video or I need another tutorial with bdm010?
@brodiecunningham3782 Жыл бұрын
You’re gonna need a different kit for bdm-010
@derickxo9 ай бұрын
Question. Can this back button kit be installed for only face buttons like X and Square? I honestly don't meed the TouchPad or R3&L3 buttons
@bigty_336 ай бұрын
but on a serious note lol are you guys doing a bdm 40 version for the mouse click triggers and buttons because I need them.
@him696997 ай бұрын
My yellow ribbon has a slight cut in it and it doesn’t work is there a way to fix it
@Baxionable9 ай бұрын
If you have the clicky kit and the rise 2.0 and want this properly installed. How to approach this the correct way?
@Bsidesthepoint7 ай бұрын
It's a great video well explained if you want to map the touchpad and the R3 L3 buttons. I ended up ruining a ribbon cable and bought a new one. I watched this video again and realized I didn't have to do any of this trickery if you ARE ONLY GOING TO RE MAP THE SQAURE, TRIANGLE, X, AND CIRCLE buttons. I know you added text to the video. But next time do it for us ass-wipes that don't pay attention, and say it in words. lol Thanks
@toastyplayz227 ай бұрын
So if I just want X and O I don’t solder and I just put the electronics in?
@clashmxson1804 Жыл бұрын
when i ordered mine it didn’t come with the tape, or the orange ribbon
@Er1ckG Жыл бұрын
I took off one of the black cables that are soldered in on the PCB 😢 how can I fix it ?
@dermf96 ай бұрын
TY!
@Insaneshane85 Жыл бұрын
Hi Craig on the bdm 30 do we still need to change the side stripes or is just the mother board I ordered the wrong kit but extreme rate was kind enough to send me the bdm30 but only got the back mother board
@CraigsChannel Жыл бұрын
Sorry for a late reply, this one's the extremerate channel not mine so just pop on every so often. With the new 30 there's no need to replace the side ribbons which is awesome news as a few people were fitting them wrong on the 10 and 20 kits this 30 means less to go wrong
@ciayr8 ай бұрын
@@CraigsChannelhi Craig how do I put back the side ribbons in, I accidentally took it out and idk how to put it back in
@rogere5585 Жыл бұрын
The white things that hold the ribbon cables on the right and left broke off
@fish-outa-bowl4122 Жыл бұрын
I bought a bdm-20 kit for a bdm-30 controller. Could I just buy bdm-30 cables and install it the Same way?? ❤
@jasvinajeeth3333 Жыл бұрын
If i dont need the l3 and r3 do i still Need to glue the ribon cable at the battery because i want to do battery replacements in the Future but if Glue the ribon on the battery i cant replace the battery
@xavierkindler300110 ай бұрын
the K1 trigger works for me but not the K2. Any suggestions please?
@spockmrssen775611 ай бұрын
is it normal that my kit the holes are NOT aligned properly? like theres like a couple mm bigger on the FPC part? is this controller different because i see the inside totally different to mine and they´re supposed to be the same model, help!! :C
@CPWeetoes7 ай бұрын
Mines flashing but idk what i did wrong
@chokoKID2248 ай бұрын
If im installing the quick triggers and the remap kit do i need to reconnect original fcp strips for triggers or are they not needed anymore (the white and blue) because in the quick trigger video they tape those out of the way
@saifdhean628611 ай бұрын
The remap mode just flashes, how do I fix the installation?
@iitsjord-_-56356 ай бұрын
Why is my controller making a clicking sounds after I installed my pack
@RodsDadBod Жыл бұрын
This kit seems much simpler with no removal of ribbons. So is it really just stick that orange ribbon it and its ready pretty much if you don't want to solder?
@skippy2831 Жыл бұрын
i want to know this too
@RodsDadBod Жыл бұрын
@skippy2831 I ended up getting one and yep it's just how it was in the video 😂 no extra ribbons and no need to solder unless you want to.
@YesSir20049 ай бұрын
Hey I need some help my K2 paddle is like instant click but my K1 like is loose a little and doesn’t it works but it’s a bit annoying and idea what’s up?
@chloealyse Жыл бұрын
for some reason the light randomly turns on and the controls ratio working. is there a fix for that?
@heitorc17892 ай бұрын
The ribbon that came in the kit didnt have de adesive to glue in place, what do i do?
@goobert2219 ай бұрын
I have a question am I able to use this and the mouseclick triggers together?
@ianbotteon4517 Жыл бұрын
My red light doeant turn on at all but my controller still turns on
@EAS151310 ай бұрын
My left paddle doenst click for some reason, its lose what do i do?? Anyone have ideas?
@itshammy6285 Жыл бұрын
which do you prefer the plastic or metal?
@CraigsChannel Жыл бұрын
Personally plastic. But guess everybody's different!
@Theheadcolddestiny7 ай бұрын
Does this work with bdm40 plz tell me
@Ghettomanjama3 күн бұрын
? Lemme know
@kevinkamphuis54918 ай бұрын
Please someone help me. My touchpad seems to not work on both controllers i did this with. What could this he?
@danielodowd8813 Жыл бұрын
Hi my controller works fine but there's no light from the paddles. I accidentally watched the rise4 tutorial while doing it but skipped all the soldering. Any ideas?
@danielodowd8813 Жыл бұрын
Sorted it, opened it back up and played around with it but it actually turned out that the light was super dim, so I had to put my hand over and make shade to even notice it
@elcino65619 ай бұрын
Non riesco ad agganciare lo sportellino in metalloConsigli?
@fadenateyt9849 ай бұрын
Ngl is it a more simple way that’s not time consuming to put it on
@skippy2831 Жыл бұрын
so if i dont want to solder i just stick that orange part on the board, put it together and im done?
@ExtremeRate Жыл бұрын
correct
@ricardolu163 Жыл бұрын
It says currently not available on Amazon CA. Are they sold out or just amazon stocking them?
@ExtremeRate Жыл бұрын
Please wait for a couple of days, the CA will be available soon
@nhatpham4847 Жыл бұрын
is the digital triggers for bdm 30 released yet? I dont see it anywhere
@ZAZUtakiyaho Жыл бұрын
im stuck man ive taken apart the controller im confused now i dont have soldering machine
@ExtremeRate Жыл бұрын
If you don't need the L3 R3 and touchpad buttons mapable to the paddles, then you don't need the soldering machine
@Arzlorz Жыл бұрын
Mine didn't come with the shell, I wasted 32$
@josearturozaunruiz1113 Жыл бұрын
It doesn’t fit at all in my controller, I just bought it. Not sure if it’s because is the newest version 😞
@chloealyse Жыл бұрын
did you check the version of your controller before buying it?
@mizzterdubstepz Жыл бұрын
I ordered the BDM010 and 020 kit but I have a BDM 030 controller. Do I have to buy a bdm030 kit or can I get the 030 cables replaced. I emailed but no response
@avoVerified Жыл бұрын
You need a bdm 30 kit for that. Bdm 10 you need a bdm 10 kit. Bdm 20 you need a bdm 20 kit. The kits need to match the controller for it to work properly.
@Sayin7273 Жыл бұрын
what if i dont want to map the R3 and L3 and also the touch pad can i still use it for the buttons?????
@Sayin7273 Жыл бұрын
meaning like no soldering if so i dont have one and i bought this product for nothin :(
@ExtremeRate Жыл бұрын
Just skip the soldering process in the video, every other buttons still works
@Sayin7273 Жыл бұрын
@@ExtremeRate okay thanks I had tried it anyways and it works perfectly fine love the product
@jasvinajeeth3333 Жыл бұрын
Can the mettall buttons rusting
@cristianortiz2215 Жыл бұрын
I install mine and it doesn’t wanna turn on at all I got the BDM030 what can I do ?
@ExtremeRate Жыл бұрын
Please try to make sure the connection between the original buttons film and the kit's main flex cable is fine
@stefansky5609 Жыл бұрын
Installed it and it works. However, the paddles don't work for a short time if I accidentally press L3 in Warzone while I'm running. This is often unavoidable in stressful situations and my jump doesn't work while I'm running because I accidentally press L3 while running. Does anyone have a solution for the problem?
@LuisMartinez-si4dg7 ай бұрын
I’m having the same issue. Did you find a solution? It works but the light turns on by itself every 10 seconds making the paddles useless
@stefansky56097 ай бұрын
@@LuisMartinez-si4dg no i don't find an solution
@m1sterkt434 Жыл бұрын
If tired all the steps but my light isn’t flashing can someone help?
@decoy1r975 Жыл бұрын
I have the same problem did you find a fix ?
@Theggfn7 ай бұрын
Is it possible to do it without a soldering kit???
@him696997 ай бұрын
Yep
@Theggfn7 ай бұрын
@@him69699 how?
@Theggfn7 ай бұрын
@@him69699 btw love the username 🤣🤣🤣🔥🔥🔥
@najetahir2449 Жыл бұрын
Do u hv to solder?
@Tiezo010 Жыл бұрын
Will the back buttons still work with out soldering?