AC 220V Multimode Learning Wireless Remote Control Switch 1-channel Relay Receiver Module

Рет қаралды 112,734

7 жыл бұрын

Aliexpress listing:
www.aliexpress.com/store/prod...
Link from DE: www.amazon.de/dp/B08CRGLWH2
AC 85V - 250V low cost single channel wireless remote control system with latching, toggle and momentary modes and remote fob code learning facility.
How to use :
About Working mode:
1) Momentary (Jog/Non-Latched) : Press one button is Working /ON. Loosen your finger on the same button is Stop/OFF. One channel switch need one buttons remote control.
2) Toggle (Self -lock/Self-Latched) : Press one button for one time is working/ON. Press the same button again is stop/OFF. 1 channel switch need one buttons remote control.
3) Latching (Inter-lock /Latched) : Press one button is working/ON, press another button is stop/OFF. 1 channel switch need 2 buttons remote control.
Clearing the code :
Push the learning button on the receivers for 8 times , the codes will be cleaned .
After clearing the code, all the remote control cannot work any more.
Learning the code : Momentary (Jog/Non-Latched)
Push the learning key on the receiver once time , it comes into momentary setting mode .
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button , LED indicator on the receiver board will flash then come off .
After 3 seconds, the LED indicator will be on again , learning successfully .
Learning the code : Toggle (Self -lock/Self-Latched)
Push the learning key on the receiver twice time , it comes into toggle setting mode
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button,LED indicator on the receiver board will flash then come off.
After 3 seconds , the LED indicator will be on again , learning successfully .
Learning the code : Latching (Inter-lock /Latched)
Note: When you choose for latching mode , in order to learn more remote control , you need to learn two different button , the first time learnt is for “ON”, the second time learnt for “OFF”. 1 channel switch need 2 buttons remote control.
For example : button A = ON , button B = OFF
Push the learning key on the receiver triple time , it comes into latching mode .
Wait for a moment , the LED indicator on the receiver board will flash then come off.
Push the remote button A .
LED flash for 5 times .
Push the remote button B .
Led flash for 5 times .
After 3 seconds , the LED indicator will be on again , learning successfully.
A = ON , B = OFF .

Пікірлер: 59

@user-sf9mh1ms4q Жыл бұрын

Finally understood it! Instructions is JUST to pair the REMOTES with the receiver. This video is showing 3 ways to fair the remote. 1. Momentary (Press receiver 1X), 2. Toggle on/off with one button (Press receiver 2X), & 3. Latching on/off using 2 buttons on or off (Press receiver 3X). RESET (Press receiver 8X).

@Istahow 3 жыл бұрын

Just buy it. It's a best learning video! Many thanks

@jlee7225 5 жыл бұрын

Thank you so much!!! Really helpful for me!!

@bruceweight7319 7 ай бұрын

I bought this switch a number of years ago and it has been kicking around in my stuff and all I could do is get it to do the momentary mode? So thanks these instructions still worked for Toggle mode which is what I wanted. Thanks!

@SPIDERLEO81 5 жыл бұрын

Hello, I have exactly the same receiver, but I would like to use it together with a 1 gang 2 way switch, that is to say turn on one light with the switch and with the remote control too, is it possible to do it with this receiver, or I need a NC COM NO output?, thanks for your answer

@postman00100 6 жыл бұрын

why sometimes I have to press few times to switch this on although I am only 1 feet away? All 2 units I bought are all the same problems. The other version without your this transformer 5 units are the same problem too.

@Bigbennek2 6 жыл бұрын

thanks,good job. great help for me. thanks again

@qiachip 6 жыл бұрын

Thank you for for support, give us more feedback about how to create better contents that suits you!

@ahmadjamil6608 4 жыл бұрын

how to automatically relay on while plug device to power??? in sonoff this name power on state...

@robintewolde1992 4 жыл бұрын

Hello, what is the minimum ampere the relay needs?

@spiritofscouse 4 жыл бұрын

can i use this to switch on and off vacuum cleaner?

@natulasnatulas8850 4 жыл бұрын

Hello good day how far is the distance from remote to the relay after pairing can it still work 3 meters away from the device?

@nashville500 10 ай бұрын

I have a similar reciever with a white remote with 1 black button and I can't get the receiver to toggle.. only moment?? Any ideas?

@peshawaaaa Жыл бұрын

Useful tips thanks bro❤

@kumaranthampi5947 4 жыл бұрын

Can i operate a single phase motor with this? how to connect??

@Julian-rb8df 6 жыл бұрын

How can I program 4 diferents remote controllers in momentary mode, for the first remote control (two buttons)

@qiachip 6 жыл бұрын

Hi Julian, I am not too sure about what you are asking. If English isn't your first language, can you please type it out using your first language? If you are trying to pair your remote control with your receiver, please press the control button on the receiver for once, wait for 1 second then press the button (the one you want to pair) on your remote control for once. And the button you pressed on the remote control are on momentary mode.

@mattross5986 Жыл бұрын

How to change channel on heimvision 241vidio recorder

@handytan233 7 жыл бұрын

regarding for the input (L & N), Using AC220V to slot inside the input right?

@handytan233 7 жыл бұрын

LIVE & NEUTRAL FROM AC220V TO WIRELESS RELAY INPUT?

@andreamitchell4758 6 жыл бұрын

is there a remote i can buy for these relays that i can tune to different codes? like one with a POT or dip switch so that i can make different FQ's for the relays to learn? i need a bunch of different relays but i am going to be using an RM pro and phone to control them so i do not need remotes at all , but i need different FQ's to teach the relays and the RM pro , is there a solutiong to this other than having to buy a remote for every relay? i already bought 5 relay boards and 2 remotes but i need more but i do not want to have to buy a remote for each relay because once i teach the remote to the relay an the RM pro i do not use it anymore

@jonerasmus9399 Жыл бұрын

Is that ac 230volt output ?

@coronavirus3595 5 жыл бұрын

can it handle airconditoner

@marcmagnier 5 жыл бұрын

Thanks you thank you thank you!!! Could'nt find any clear instruction anywhere!

@qiachip 3 жыл бұрын

TUYA Smart Products have been launched on Amazon-US on March 3! In order to thank everyone for your attention and support to our brand, we have separately prepared a time-limited new claim activity for your region; We hope we can bring something positive to your day-as our way of saying thank you for supporting us. Get free,pl contact email:daisy@rodotdiy.com Coupon code: 15RODOT12 www.amazon.com/dp/B08VDXDFM5

@borisloncar3011 5 жыл бұрын

Have you directly connected to your relay device at a voltage of 220V

@ChrisVayos 7 ай бұрын

Perfect video.

@panuwatpnc8462 4 жыл бұрын

how many remote It can memory

@cidinhoeletrotecnico2779 7 жыл бұрын

Muito bom

@mxr4k101 3 жыл бұрын

Is it possible to make a parallel connection with a normal physical switch?

@qiachip 3 жыл бұрын

What function do you need, we can customize the product according to your needs.

@stanleybinns1412 5 жыл бұрын

What is the input voltage , I can see a 12V relay !! .

@Perplexer1 5 жыл бұрын

Input voltage is 220V AC. Output voltage is also 220V AC. But relay uses 12V to work yes. Other elements on the PCB convert the 220V to 12V for the relay to work.

@freehugs5318 2 жыл бұрын

Can you tell me how you use different remotes in one receiver

@qiachip 2 жыл бұрын

Hello, you only need to pair each remote control with the receiver one by one. Please note that you don’t need to clear the code anymore

@jakedreynolds 7 жыл бұрын

How do you setup for the relay to be normally closed?

@qiachip 7 жыл бұрын

This receiver has no normally closed function.

@andreamitchell4758 7 жыл бұрын

how do i wire the relay ? and can i control something that does not require power? like can i power the relay with my 110v AC and then use it to switch my garage door opener button ,like with a 12v relay by connecting one wire to common and one wire to NO? i do not understand where the live wires go either this thing is badly labeled it just says IN on one side an L and N on the other but there are 3 contacts on that side

@qiachip 7 жыл бұрын

Do you need this? : Https://kzfaq.info/get/bejne/oZZmpJpn1trMcqs.html

@Dendrotera1 5 жыл бұрын

This can be use with 12v power supply?

@qiachip 5 жыл бұрын

kzfaq.info/get/bejne/erJ4p8ynyc2tqoE.html this can be use with 12v power supply

@sarathmd1510 10 ай бұрын

❤❤❤

@irvingdeleon 4 жыл бұрын

Thank you guy, you save me from destroy my relay jajajaja. If you need help with the spanish translations can you tell me c:

@ArturHot 4 жыл бұрын

Can į connect to output 12vled strip?

@acpelayo135 2 жыл бұрын

Is the NC terminal functional in this module?

@qiachip 2 жыл бұрын

Yes, the NC terminal works normally.

@acpelayo135 2 жыл бұрын

So it would be possible to use this in a 3 way setup right?

@johncoops6897 2 жыл бұрын

@@acpelayo135 - you simply program 3 remotes to one receiver. That is the normal meaning for 3-way.

@acpelayo135 2 жыл бұрын

@@johncoops6897 I was planning on using it with a 3-way switch. That way I could turn on/off the device using either the remote or a physical switch

@johncoops6897 2 жыл бұрын

"2-way" means different things in different countries. Below I am assuming you mean 2 switches where either can switch the light both on and off. This is done with a special wiring system that I won't explain in full detail here. If your existing switch is just a single, then you can use this device's NO, NC and Common to create a 2-way (2 switches on one light), but you must add the extra change-over wires between the existing switch and the relay. However if your existing setup already has 2-switches, then this device wont work as a third switch. To do that you need what is called a "change-over" switch. This is inserted into the 2 switch wires that run between the existing 2-way switches. So for the third (or subsequent) switches you need a Double-Pole Double Throw that is inserted into the 2 wires (running between the 2-way) that reverses the polarity of the 2 wires. See en.wikipedia.org/wiki/Multiway_switching [see next reply]

@ajatsudrajat5768 Жыл бұрын

Bikin tutorial nya buat bos😁

@boyetz88 4 жыл бұрын

The issue with this remote controller is in about a year nasisira din cya..ilan beses nkong nagpalit ng ganyan

@piqlerstudio 3 жыл бұрын

嗨，我买了一个接收器，按了8次钮后，红色灯持续亮着没闪，然后过一阵子又暗了。。。

@qiachip 3 жыл бұрын

Can you send us a video, our engineer will help you check the reason

@piqlerstudio 3 жыл бұрын

@@qiachip Hi, i have figured out the problem, because my remote control not compatible....i changed one then ok d. by the way, my version of receiver red light doesn't blink, it keep on then off, a little different, but setting steps is same. Thanks.