Quick And Easy Gear Repair Without A Lathe an easy way to repair teeth without a lathe, with the correct welding method you will get better quality
Пікірлер: 872
@Mauzer-9996 ай бұрын
Отличный ремонт ! Теперь, после восстановления всех зубьев, эта шестерня без проблем подойдёт для украшения какого-нибудь столика в стиле стимпанка ))
@user-im3if8pi5w6 ай бұрын
Ну да...Или просто кучи металлолома.
@ardentdemon93446 ай бұрын
@@iwankim8150Хах😂😂😂😂😂😂😂 😂
@user-sj6rp3nb3k6 ай бұрын
Ппц, и зачем я тратил время на эту дичь? 😂
@PavelM4796 ай бұрын
Однозначно, надо чтобы подобный кринж блочил ютуб😂😂😂 самое то ужасное то, что есть те, кто истинно верит в то что это имеет смысл🤦♂️🤦♂️🤦♂️ Зуборезные и фрезерные станки??? Закалка детали??? Неее... не слышали🤦♂️🤦♂️🤦♂️
@helloslayer6666 ай бұрын
У него электроды для твердосплавной напайки.
@kextrz2 ай бұрын
This is one skilled craftsman. It doesn't mean the gear hasn't been permanently damaged by the process, or that it will be able to take any significant load without breaking and creating more damage. However, as an exercise, a curiosity, or a very temporary solution, it's quite impressive.
@mnztr1Ай бұрын
yes I was wondering about the heat damage to the gear, and IMHO I doubt it can take much load.
@paulopaniago597225 күн бұрын
@@mnztr1 Many gears are made of soft steel that can´t be hardened by heat treatment, and are not designed to handle big loads, so those would simply continue working. The repaired tooth can be nearly as strong as the other ones and they doesn't tend to get brittle eider after soldering. Now, heat treated high carbon steel gears, or even surface hardened gears might be ruined by these kind of repairs.
@SR-gs8zo22 күн бұрын
thta,s exactly what the commenters meant by "ruined", but i disagree about " mild steel mostly" which is not true....gears are mostly hardened and even differentially hardened to keep the wear resistance on the teeth and the elasticity and shock resistance at the center...it depends on the aplication, he did a good job on rebuilding the geometry with only simple tools( so one might not even assume welding and a grinder simple at all, bcs simple would be only hand tools, hmmm? ) and yes, the job is well done in that matter, but under loads and high speeds i wouldn,t use this other than a last resort, and most of all not in an automotive application!
@paulopaniago597222 күн бұрын
@@SR-gs8zo I also thought gears where all hardened steels, for a matter of logic. But at least here in Brasil, the steel most commonly used to make gears, including crown sprocket are mainly sae1020, according to their own specifications when you buy them, which is not hardenable, but can be cemented (surface treatment). Although for any higher speed applications, those would be hardened high carbon steels. But I agree that he made an excellent job.
@mnztr121 күн бұрын
@@SR-gs8zo maybe he connducted some hardening procedures after.
@user-dn3ov9uf6o6 ай бұрын
1. Наплавка в пламени горелки - очень грубая операция, пережигающая и основной металл, и наплавку. Теми же электродами на небольшом токе с минусом на электроде можно было сделать нежнее, о наплавке проволокой в углекислоте я уж не говорю. 2. Воленс-неволенс, было бы неплохо шестерню после наплавки отпустить, а после механической обработки калить. Все-таки напряжения в корнях новых зубьев снялись бы, и выровнялась бы структура металла, насколько это вообще возможно в таких условиях. 3. Эвольвента - это не выдумка маньяков, её надо почитать и выполнять как можно точнее. А тут.... На самый худой конец можно сделать шаблоны с профилем нескольких зубьев, наложить их н венец с обеих сторон и по ним выводить профиль. Но все равно это "на безрыбье". 4. Всё это хорошо, если шестерня - стальная. А вот если основной металл - чугун, то всё это - фифехт фиксии. Металл у корня зуба обязательно отбелится, а белый чугун - хрупкий, как сахар. То есть, его можно попытаться наплавлять чем-то легкоплавким типа бронзы или табуна, а наплавлять сталью - чистое безумие.
@robertvolpert89866 ай бұрын
I arc welded an outboard motor flywheel gear in 3 places. I made a template of about 10 teeth. Each spot needed 4 or 5 teeth welded. Ground it the same way. Came out great. Been using it for two years,still looks great. Saved about $500 dollars. Used a $60 ebay arc welder. 👌
@user-uz7hd5er4m6 ай бұрын
Я писал дипломный проект на Минском заводе шестерён (в семидесятых) и вы ,наверное поймёте моё негодование.Этот ролик-это воинствующее невежество.
@user-dn3ov9uf6o6 ай бұрын
@@user-uz7hd5er4m В Орле был точно такой же завод, моя мать там работала в ОГТ, а я бывал в цехах. А тут вот такое выдают за мастерство.
@miszad58256 ай бұрын
@@user-uz7hd5er4m ----Полностью согласен, что это барахло, я специалист по изготовлению шестерён.Но самое интересное то, что именно так, без зубообрабатывающих станков, самые первые 10 груэовиков АМО-Ф-15 для праздника 7 ноября были вручную изготовлены их коробки передач
@helloslayer6666 ай бұрын
Это мотоциклетная шестерня с 150-250 кубового чахлого мотора. Материал сталь какой-то марки. Что значит переживание? Ничего что у него науглероживающий режим горелки включен? Вы так негодует будто шестерня в грузовике Ман будет стоять. Это дешёвая мотоциклетная, шестерня от китайца.
@gregsutton6258Ай бұрын
I repaired a 1200 mm gear that had a small power gear with a dropped out keyway stuck to it, every 12th tooth was gone an old welder bronzed it up and I re cut the teeth with a dremil and files, it ran for 9 years and never failed. Good work
@smartechsolutions18606 күн бұрын
Yes in lower power installations can function but not at higher power ones, maybe for starters or for intermediate processing about not direct work flow i wouldn't recommend it.
@gregsutton62584 күн бұрын
2.5 horsepower electric motor, machine spinning 1.2 metre x 1.4 metre high cast iron cam stamping caps onto a bottle and rolling threads in aluminium caps at 1700 RPM is light work of course even after 10 hours shifts for 9 years, however it never broke, the same welder also did Leyland and Mack tuck great boxes in the 1960s and 70s that hauled iron ore in the Pilbara of Western Australia, he laughed when I asked is it strong enough?
@misterx29856 ай бұрын
Хотел написать, что сильно сомневаюсь, что эта шестерня будет работать в каком-то механизме, но умные люди до меня уже всё написали.
@ACTBotRussian3 ай бұрын
есть сомнения , что они не умные и ты тоже
@misterx29853 ай бұрын
@@ACTBotRussian не суди по себе о других, умник...
@WinyThePoohАй бұрын
Да будет. Притрётся в конце концов. Если не выломает навареный кусок
@parasitizeneuron189327 күн бұрын
Конечно, притрется.. угандошив попутно соседей по коробке😁😁
@sergin0v47416 күн бұрын
В КПП легкого авто не поставишь , но такой ремонт реален для приводов сельхозмашин и прочего. Проверено. У меня порвало гипоидную передачу на копалке. Восстановил аналогично. 5 лет работает нормально. Прошлой осенью вскрывал , смотрел , всё хорошо , ещё годы проработает)))
@50Zmey6 ай бұрын
А коленчатый вал напильником пробовал расточить? У такого мастера, я думаю, получится.
@user-gf8fo9gg2v3 ай бұрын
Нее, нужен рашпиль!
@user-dw1df5rx8pАй бұрын
Самый лучший ремонт колеса с поломанными зубьями - изготовление нового!
@HorstJarnuszak22 күн бұрын
Richtig!
@brianfreeman36765 ай бұрын
Gears are case hardened. If you get it red hot, it will soften it. On the other hand, if a replacement isn't available, I don't see anything wrong with trying an idea like this. Depending on what the gear goes to, and what the torque load is on it, it may last for the life of the machine. Thanks for sharing.
@BeltFedToys4 ай бұрын
Let's face it, if that repair could last the rest of the life of the machine the original would never have broken. Plus the part damage was staged, a gear would not shear three teeth perfectly like that and the other gear would also be damaged.
@elijahwhatshisname7481Ай бұрын
Such videos are nothing more than information noise. As a rule, they are staged and filmed for the purpose of getting views and likes. Harm to humanity.
@user-ru5kn4mj5t6 ай бұрын
Стальные шестерни - не тот случай, когда можно приварить новые зубья. Даже если оригинальные зубья сломаны, при затяжке приваренные сломаются еще больше. Правильно было бы выточить новую шестерню из аналогичного материала, а затем правильно закалить эту шестерню по технологии, как того требует технология. В противном случае этот брак не состоится. Более того, соседние участки металла при нагреве теряют свою технологичность и быстро выйдут из строя. Вот если из-за этой поломки вы застряли где-то очень далеко от цивилизации, и у вас нет выхода, то есть смысл сделать такую снасть. затем, молясь Богу или Аллаху, двигайтесь осторожно и медленно, чтобы добраться до людей, не сломав свой шедевр. В любом случае это долго работать не будет. И да, все эти измерения штангенциркулем херня полная, там допуски что бы шестерня работала под нагрузкой и не ломалась идут в пару соток и меньше, а тут он чуть ли не в миллиметр плюс минус! Это просто трешь!
@user-il1sp6tc4y6 ай бұрын
А как это далеко от людей, но с газосваркой?
@user-ek9we5lg2h6 ай бұрын
@@user-il1sp6tc4yесли он сварщик и у него сварка в автомобиле, а шестерня снаружи и её можно легко снять😅😮
@user-ws4qr8vl8i3 ай бұрын
Пластелиноавя ворона
@user-dz3mj6ee5y3 ай бұрын
Согласен, что приварить зубья сложно... А вот клей "Момент" будет самое оно!
@user-qx9uv7rn3l3 күн бұрын
Спасибо, порадовали грамотой. Единственная ошибка- треш. Это слово мужского рода и мягкий знак тут не ставится.))
@user-on2dm3js7u6 ай бұрын
15 лет назад у нашего кухонного комбайна Мрия 2м на большой алюминиевой шестеренке сломался зуб. Кость попала в мясорубку. 2 месяца я искал замену и не нашел. Сделал так: просверлил 2 дырки рядом 2мм, взял 2мм подкаленную проволоку, согнул скобу, сунул в дырки и расклепал концы. Затем надфилем придал скобе форму зуба. Работает до сих пор.
@user-fv8eg1ru7v6 ай бұрын
дырки бывают в жопе и в сельском туалете, в остальных вещах отверстия!!!! А да, дырки бывают еще в пустой голове.
@Alex-03105 ай бұрын
В зацеплении одновременно работают 6 зубьев, по три на колесо. Ваш восстановленный зуб не выломался потомучто два соседних берут на себя нагрузку, он просто не работает...
@user-on2dm3js7u5 ай бұрын
Увы, неправы. До ремонта проскакивала шестерня, потому и взялся за ремонт! ))@@Alex-0310
@user-vt5qh5xx6j4 ай бұрын
😅
@user-vt5qh5xx6j4 ай бұрын
@Alex-0310
@user-ky4wl1rv8b6 ай бұрын
Раньше делали в колхозах. При уборке зерновых в сизон. Реально в те времена небыло запчастей. Легче было заказать технику чем запчасти. С логистикой было всё плохо. При поломке наваривали обычным электродам уони и трактор уходил в поле с шумами и в надежде притрётся. Дорабатывал норматив. Бывало ломалось на высоких нагрузках и заново варили. Для небольших и средних нагрузак имеет место быть
@user-hd9vj3kh1z6 ай бұрын
Было дело. И такое выражение как притрется тоже😂
@Alex-03105 ай бұрын
да - делали, но подгоняли по шаблонам эвольвенты, а во вторых делали термообработку, и опять же, такой ремонт на несколько десятков часов работы - если повезет....
@user-eg8sy4tf9q4 ай бұрын
Если варить уони и одновременно нагревать эту шестерню тем же автогеном, затем положить ее в печь с температурой градусов 600, на часов 8 , понижая постепенно. Потом калить в масле. Толк более менее будет
@user-id3jk1kf3s2 ай бұрын
Я работал токарем на заводе. Такую шестерню на 1к62 за пол смены мог сделать. оставалось заказчику еще магарыч на термичку отнести!
@bogdan_7511 күн бұрын
Просто тогда не было слова «логистика»😂
@A.Hisham866 ай бұрын
I was expecting you to install it on the engine and wait for the teeth to break. Because, since it's not exanimated thermally , it'll definitely break.
@artszabo10156 ай бұрын
"exanimated" means deprived of life - in other words 'dead'. So what you are saying is that if a gear is thermally dead it will break. Thermally dead would mean cold wouldn't it? So we can now conclude that warm gears break and cold gears don't. How utterly enlightening!! Art from Ohio
@ernestozentenosuarez89706 ай бұрын
Los metales al calentarlos pierden sus propiedades de dureza. Para que los engranes no se rompan se necesita aplicarles un procedimiento térmico después de soldarlos para que recuperen su dureza de lo contrario se romperán definitivamente
@zivoradmirkovic97656 ай бұрын
Ovaj se sigurno nece slomiti posle ovakvog varenja postaje mekano gvozdje mogu samo da mu se pokrive zubi u svakom slucaju je vise neupotrebljiv
@andreydonskov4896 ай бұрын
Ничего там не сломается. Нет ничего постоянней, чем временное)
@therealjammit5 ай бұрын
Seeing how it's no stronger than a braze and how it looks like there was previous repair damage elsewhere I would say this is probably in a low stress machine and would work fine for the use as intended. Edit: typo corrected.
@KalatSaarАй бұрын
ok nice Work .. now a Ball bearing in the center and You have a verry nice Fidget spinner
@user-cm1od3dz3m3 ай бұрын
Отличный мастер. Болгаркой воспроизвел эвольвенту профиля зубьев. Для механизма лебедки подъема ведра воды из колодца вполне подойдет.
@josueramos40964 ай бұрын
Já fiz muitas recuperações em engrenagens, mas depois da solda é do acabamento com a esmerilhadeira refazia os dentes na fresadora com a fresa compatível com o módulo dos dentes.
@fenixjune6 ай бұрын
Работать в приводе вращения новогодней елки эта шестерня работать будет, худо-бедно. А в более ответственном механизме (особенно высокоскоростном) к шлифовке эвольвенты на каждом ремонтируемом зубе надо-таки подойти было потщетельней. Ну и выравнивающую термообработку надо провести (хотя я непонял какая там марка электродов применялась).
@biktorfedoseev71196 ай бұрын
Это каквременная пломба зубная улыбаться можно жевать нельзя
@zelyaev_albert6 ай бұрын
Главное чтобы за ворота выехало.А там-в чьих руках сломалось,тот и виноват.
@ceciltrane54186 ай бұрын
@@biktorfedoseev7119😅
@Alexandr_Nemts3 ай бұрын
Для вращения ёлки вообще достаточно дешёвого пластикового мотрчика или каких нибудь шктвов с помойки с нанчнутыми старыми колготками жены, а здесь потрачены деньги и время.
@montesamapping4 ай бұрын
Some good ideas for not hard work gearbox. Maybe useful for plastic parts, using dual components resins and then remodelling teeths.
@pipeepapofckgug36333 ай бұрын
Do you always butter your workpiece before grinding it?
@user-gx7iq7io2s6 ай бұрын
Быстрый и простой ремонт без токарного станка, и автор не солгал, а вот что эти шестерни после ремонта можно использовать вновь - об этом речи не было.
@fuckros6 ай бұрын
А токарный тут вообще при чём?! Можно было назвать ролик "Быстрый и простой ремонт без газонокосилки"
@user-gx7iq7io2s6 ай бұрын
@@fuckros Специально просмотрел видео по методам изготовления шестеренок, их множество и отливка и накатка и фрезерование разными фрезами на больших оборотах. Так что и токарный станок здесь применим. Насчет газонокосилки - это инструмент, которым не изготавливают, а часто разрушают шестерни ведущего или ведомого валов.
@user-uz7hd5er4m6 ай бұрын
Согласен и добавлю-можно было и без болгарки.
@user-ru5kn4mj5t6 ай бұрын
Steel gears are not a case where new teeth can be welded on. Even if the original teeth are broken, the welded ones will break even more when tightened. It would be correct to machine a new gear from a similar material, and then it would be correct to harden this gear according to the technology, as required by the technology. Otherwise this marriage will not work. Otherwise, this marriage will not take place. Moreover, adjacent sections of metal lose their technology when heated and will quickly fail. Now, if because of this breakdown you are stuck somewhere very far from civilization, and you have no way out, then it makes sense to make such gear. then while praying to God or Allah, move carefully and slowly to reach people without breaking your masterpiece. In any case, this will not work for long. And yes, all these measurements with calipers are complete bullshit, there the tolerances for the gear to work under load and not break are a couple of hundredths or less, but here it is almost a millimeter plus or minus! It's just rubbish!
@Tester-scratch2 ай бұрын
Really interesting - under certain circumstances, this could be a short-term lifesaver
@mihaithaАй бұрын
the circumstances being that you don't use that cogwheel anywhere.
@frasercrone3838Ай бұрын
Those teeth will strip when put under load. Gears are a circular lever and the load is dictated by the ratio of one to the other and that determines torque load. They are also heat treated so they do not wear out quickly due to friction from steel to steel contact. Oil is a friction modifier not an eliminator.
@Tester-scratchАй бұрын
Agreed, but some gearing is not really load-bearing - simply a time-keeping mechanism, such as in a watch.
@andysutton6436Ай бұрын
I have done this kind of repair. However this guy seems to be using an incorrect flame to make the deposit and the sparks indicate that oxidising is occurring. Assuming the gear is a steel alloy then three different filler materials are required. A prepping material for the first layer the second should be a mid range ‘stellite’ and then a full hard stellite for the final layer. This will result in a good bond with the original and a progressive strengthening to full hard on the surface. A good welder will be able to produce a fair profile for each tooth requiring little machining to achieve a finished job. Done properly the repair will be better than the original. If the gear is subjected to a pulsing load then the gear should be reset to introduce previously unstressed teeth. A typical scenario is from the reciprocating ram on a hay baler where we used to reset the bull wheel and pinion gear some 90 degrees from the current load zone. We did this every 3 to 4 seasons according to the workload. This saved the customer downtime during the season.
@gavrosalex47286 ай бұрын
Удивительно, но недавно я видел ТЗ на восстановление зубьев большого колеса поворотного механизма ветрогенератора, без снятия колеса. Основано на опыте уже ранее проведенных ремонтов. С нас требовалась только наплавка и восстановление с применением УШМ до соответствия контрольному шаблону. Отказались в итоге от работ "под улюч"
@KarelSeeuwenКүн бұрын
Excellent work using only the minimum amount of tools.
@angelgonzalo2885Ай бұрын
Magnífico!! ,insuperable!! mejor que arreglarlo con madera!.
@jerrybigrig94756 ай бұрын
Sooo.. How do you harden those welds ..to become gears.. Or is this a temporary repair to sell that motorcycle..and when it explodes...AGAIN.. Now it's someone else's problem..??
@fidelcatsro69485 күн бұрын
Yes someone else problem..😂😂
@gernothohl40586 ай бұрын
Nonsense, it won't hold up if it's really supposed to transmit power. No involute. No hardening.....without words. Without power transmission, only ok as a movement or temporary solution.
@girininkas6 ай бұрын
👍💯
@faustinoflores59546 ай бұрын
Un trabajo muy malo disculpen pero es así eso se rellena con un electrodo duro por ejemplo un 106 o conargen 1400 previo calentar la pieza antes de comenzar
@user-wv2uu2lo1n6 ай бұрын
Затея неплохая. Но многое зависит от твёрдости. Смотря какую функцию выполняет эта шестеренка..
@user-ek9we5lg2h6 ай бұрын
Перекуп-вариант, пока продает можно поездить!
@user-dq9tz6pw7r6 ай бұрын
Ещё можно загнать за бутылку.
@user-rb4yj3hw1b6 ай бұрын
В добрые времена,когда в ходу были Мински и Восходы ,этот ремонт был шедевральным .Наличие УШМ т.е. болгарки тебя приравнивало к Божеству , а если ещё был сварочный - ты Бог .Но самое главное - управляться этим всем и чтобы руки не дрожжали от Паркинсона . После такого ремонта можно было вечерок аккуратно позажигать .
@fanatykCZ5165 ай бұрын
Звенящая бедность
@user-vc9xx4qh5q4 ай бұрын
На любом заводе могли сделать за пузырь Так шо не звизди!
@user-rb4yj3hw1b4 ай бұрын
@@user-vc9xx4qh5q А если живёшь не в городе ,а в деревне ?
@Sl203 ай бұрын
My respect ,very smart ,love it !!!🔴🫢🤫
@stanisawmuszynski89782 ай бұрын
Precizion job,very nice👍👏
@miguelcarvalho159211 күн бұрын
Fiz um reparo desses semana passada na tig, é bem prático e ficou muito bom.
@MrRichard570004 ай бұрын
Ii that a base electrode you are using???have some worn dogbones on a 80 cc dirtbike ,can i just try to weld it with a nicroma or base electrode???anyway great methode,realy cool
@VINOGRA6 ай бұрын
Автор, если постарается, то и новую такую шестерню этим способом сумеет сделать, например, из обломка рельса.
@ramonjorgemartinez411Ай бұрын
Hola muy bien reparado hace unos días repare un engranaje de distribución de acero de un motor de un barco y quedó muy bien soy de argentina
@user-gw9ic5yl8l6 ай бұрын
Я сам из колхоза, но такого колхоза не делают и у нас в колхозе😂😂😂
@TradeWorks_Construction6 ай бұрын
Braising stick welding electrode filler metal, I’ve seen some pretty “unique” fixes on KZfaq labeled welding hacks and for the most part I can’t disagree They are most certainly hack jobs someone was too cheap or lazy to do it right the first time. But hey if it holds together please do a detailed follow up including its install location, type of load (constant, variable, intermittent or pulsing start and stop engagement), gear train changes, Motor HP and rpm, approximate hours or days of service life and some close ups of the new gear teeth showing the wear incurred.
@nightbinary83372 күн бұрын
благодаря такому методу можно без проблем установить ее в механизм , а потом починить уже весь его целиком повторяя операцию для каждой детали , чтоб закрепить так сказать результат
@user-gh9fs4qm2d4 ай бұрын
Электрод изготавливают из конструкционной стали, а шестерню из инструментальной. И еще как правило с закалкой зуба. Такой ремонт шестерни только на полчаса работы механизма. Металловедение? Не, не проходили!
@verdergreen322 ай бұрын
Не на пол часа, а на пол минуты. А потом кирдык всем остальным еще целым шестерням из - за кусков и стружки в которые превратятся эти зубья.
@sergin0v47416 күн бұрын
Рассмешил))))) Такой ремонт реален для сельхозмашин. Сам аналогично ремонтировал шестерни на картофелекопалке. 5 сезонов отработали , ещё лет 10 выдержат))))
@11111kuba2 ай бұрын
Witam ciekawy pomysł! jaka to pasta i elektroda?
@lobosemestepe6669Ай бұрын
Dependendo onde vai trabalhar essa engrenagem é muito arriscado colocar de volta.
@user-gx7uo4ot1f6 ай бұрын
Мастер сказал что еще 100 лет будет работать в виде кулона 😁
@user-ct2xw7pb1s5 ай бұрын
Плавали
@user-sz8vl1ej1z2 ай бұрын
Buen trabajo sin torno ni cepillo 🙏🤗
@edgardodanielwitt7254 ай бұрын
Que bueno!!!gracias!
@hectorr8146 ай бұрын
EXCELENTE VIDEO¡¡... Y MUY ILUSTRATIVO¡¡...SALUDOS DESDE MEXICO¡¡
@electro_genius6 ай бұрын
Как всегда очередной виртуоз самодельщиков! 😅😂 Ну конечно если всего один раз надо отремонтировать шестерню себе, то вот так заморочиться можно, хотя это на любителя. А так это занятие, для тех кто никуда не спешит или любит всяко играться с инструментом. А если уже говорить по существу, я сам шестерни изготавливаю и все это проходил. Здесь человек шестерню сделал исключительно одной болгаркой! Я не в шоке, но то что он показал в конце что типа зубы вошли в зацепление и работают - это все фигня! Надо поместить шестерни в механизм в сборе и крутить, вот тогда видно будет клинит или нет, может шумит, по крайней мере там он точно может доработать их по необходимости. Эвольвенту болгаркой нереально сделать. Но в любом случае удачи мастеру в его развитии😊
@tarciliobeneditodasilvafil3921Ай бұрын
Lindo, lindo trabalho 👍👍👏👏👏
@user-on3kz5jq8o6 ай бұрын
Даёшь пакистанский ремонт в массы!😂
@JaapGrootveldАй бұрын
Bless you.
@mart-mi3mn6 ай бұрын
На таких зубьях можно будет доехать до магазина, где шестеренки продают :)
@user-uu3ir2nz1q6 ай бұрын
Если бы зубья обработал профильной фрезой, то шестерню можно использовать в неответственных механизмах или в неответственных домашних самоделках, где нет экстремальных температур и нагрузок, или в музейных экспонатах. После такой механической обработки шестерня не преобрела ни прежнюю аутентичную форму, а свойственные ей харектеристики из-за термообработки утрачены.
@robertopablovizcarra30236 ай бұрын
Muy buena opción cuando no hay dinero, abria que hacerle un tratamiento termico para normalizar la pieza.
@user-ju7ie3nx2eАй бұрын
Отличный вариант замысла, привлечь внимание.
@user-hi7ep7mu6o6 ай бұрын
Кто тоже ждал конца ролика , только из-за того , чтобы посмотреть как это произведение рукожопого искуства полетит в мусорку ?
@jenatjenuvlogs33053 ай бұрын
Which electrode use
@Teipd1708 күн бұрын
Si ça tient 24 heures bravo 👏👏👏
@ogreunderbridge52044 ай бұрын
Absolute minimal need of fancy tools to get there. I love it ! A little fine tuning and tempering and it will be good as new :)
@Naeiou6 ай бұрын
This is a lost art. Of course it won't hold up in something like a tractor transmission, but of medium use it's very durable. Have seen this done many times on machinery with NO failures
@josemiguelmachadomendoza260723 күн бұрын
Eso puede suceder en cualquier parte del mundo donde la economia te obliga a ser ingeniozo ... Me gustaria saber si esa fuera una pieza importante de un vehiculo o de una maquinaria costoza se arriesgarian a realizar ese trabajo ?
@regd.22634 ай бұрын
What was that white paste you put on the gear at the beginning of the video then it was taken off in the next shot then later put back on again.
@fidelcatsro69485 күн бұрын
Toothpaste with flouride to ensure good resistance against tooth decay! 😂
@RussellBooth19775 ай бұрын
The gear will need to be heat treated again, when I was repairing power tools I was warned against heating up a gear using an oxy acetylene torch because that can soften the gear. The gear teeth aren't polished,I can remember when my manager had to use valve lapping compound to lap in brand new Hitachi angle grinder gears which were noisy out of the packet !
@robertdouglas34562 ай бұрын
What a Craftsman at work! Great work!🤩🤩
@user-nd9tp6wg5sАй бұрын
Даже , если случится чудо и он каким то образом угадает с профилем зубьев , то при сварке нарушилась заводская термообработка . И зубья должны иметь цементацию . Деталь надо отпускать и калить снова с цементацией .
@gerardoelenes51304 ай бұрын
Muy buen trabajo
@erdoganoz5808Ай бұрын
Videonun başında vitese sürdüğünüz o beyaz macun neydi
@nobs_89394 ай бұрын
Ife done this one Time on a harvester Elevator, still holds perfekt since 2016
@excalibur79696 ай бұрын
A no ser que sea para un juguete ,un reloj o un mecanismo de trabajo muy liviano, sinceramente no creo que esa reparación aguante un trabajo como engranaje. Pero felicitaciones.
@user-yi7re7uu1v6 ай бұрын
работа от!!! Ценного Специалиста😁🥲😂🤣
@georgemacdonald3087Ай бұрын
What exactly was "easy" about that?
@Bianchi77Ай бұрын
Creative video, thanks :)
@Grayhaired19 күн бұрын
Сильно впечатлило особо точное восстановление эвольвенты болгаркой. Понимаю, что цементация будет в солонке, но до этого не хватило сил досмотреть.
@maheshwarbhagan4058 күн бұрын
Great work can ask for better
@mikespain86553 ай бұрын
NEVER one hand a grinder, even for two seconds. This repair is crude at best.
@josemaciliocardoso11923 ай бұрын
Show, parabéns 👍👍👍👍👍
@piotrwysoki87013 ай бұрын
Nadaje się tylko do dekoracji, koła zębate są utwardzane a takie napawane zęby są miękkie i bardzo szybko się zużyją, jeśli się wyłamały to znaczy, że maszyna w której była ta zębatka ma duże obciążenia, czyli lepiej to wygląda niż się do czegoś nadaje. Pracuję w metalu to co nieco wiem na ten temat.
@MarkusK.-wx9ge5 ай бұрын
Das Schnellste und Einfachste wäre, ein neues Zahnrad zu besorgen. Geht auch ohne Drehbank!
@TheRa5traАй бұрын
i think its just for pinion, not transfering power movement into another shaft, but its not safe component for long term usage
@wh0tube2 ай бұрын
Precision dentistry! 👍
@fidelcatsro69485 күн бұрын
Theyre dentists and mechanics, double diploma
@DavidYun-vx4de6 ай бұрын
좋은 영상입니다. 하지만 보수한 기어 각 이빨의 피치와 압력각, 백래시 등을 보장할 수 없을 듯합니다.
@86yurek6 ай бұрын
Так конечно интересно, но хотелось сравнить её с заводской) Ну или хотя бы ножиком проверить зубья)
@leeds31936 ай бұрын
good Your the best.
@gepardchester64954 ай бұрын
Czym szlifujesz nazwa typ tarczy?
@joseoliveira46782 күн бұрын
Essa engrenagem depois de terminada, só serve para peso de papel. Qualquer ajudante de mecânica na sua primeira semana de trabalho, como tal, sabe que é impossível isso funcionar... Mas valeu, foi terapêutico assistir esse vídeo... rsrsrs
@andrzejporeda72816 ай бұрын
Oj przepiękne jest to odrestaurowane koło zębate pozdrawiam mile i serdecznie 👍👍👍👍👍👍
@Enrique-yo1jc3 ай бұрын
Bueno
@MichaelBegelspacher6 ай бұрын
Unbelievable. Your the best. Thanks a lot for this great video. 🙏🏻
@user-lh1oz4hj3m5 күн бұрын
Интересно было бы посмотреть восстановление шестерни с помощью токарного станка.
@user-fl9eu7cs9l3 күн бұрын
Si ubiera usado electroeo de cilisio si es bastante duro de lo contrario no sirve la reparación es fundir Toto el material ponerlo en plantilla de arcilla y antes de volcarlo ala plantilla agregar cilisio al acero y volcarlo al aceite para templarlo si se doblo hacerlo otra vez
@vincenzorosciano88206 ай бұрын
Salve bel video, peccato senza sottotitoli.
@user-fy5jg9xs8hАй бұрын
Теперь эта шестерня мягкая,как алюминий.Металл опустил,а закалить забыл
@davereina77752 ай бұрын
What type of stick rod was used for this repair?
@hollywood48342 ай бұрын
Looks like a standard arc welding rod
@yohanesrochadim.mar.e47256 ай бұрын
Wow, this patch is very dangerous if you use a load, even though the original just broke, if I didn't dare to use a reconditioned item like this it would further damage the other parts so it's vital, it's best not to imitate it except for displaying the senab, this is dirty technology.
@valdirxavier63556 ай бұрын
Excelente profissional, porém não creio que vá ser funcional esse trabalho, você alterou as características físicas desse material quando o superaqueceu eu acho!
@Rectifjuillet12346 ай бұрын
Parfait,et simple
@YamahaWR2006 ай бұрын
Ah yes. The notorious “casual welder” and “professional grinder.”
@leonidasmarquesjerico38836 ай бұрын
Vai quebrar , sem dúvida alguma !!!
@senhorsolar7213Ай бұрын
Que materiais são usados?
@jorgeenriquetrianarojas23473 ай бұрын
Bueno el trabajo pero quedó faltando el tratamiento térmico
@jediatricwalker93826 күн бұрын
How about those precision grinders and that marking pen, Nothig says Swass Witch quality quite like this part repair.
@rodrigotorresaguilar25673 ай бұрын
UN TRABAJO MUY RAPIDO PERO LO CORRECTO ES ASER OTRA PIEZA NUEVA.....SI EL ENGRANE C DESDIENTO NUEVO Q C ESPERA D UNOS DIENTES FALSOS ( DURARA MNOS)
@user-kx2ct5ek2i6 ай бұрын
Так перегреешь и шерстеренка не годная будет. Лучше полуавтоматом с охлаждением.
@marcragueneau28136 ай бұрын
un ajusteur fera plus propre, plus régulier, plus précis ... peut-être un peu plus de temps mais parfaitement solide. Pour refaire les dents de pignon, nul besoin de tour !!! merci