Quick tip #8 Electronic Edge Finder

No video

Quick tip #8 Electronic Edge Finder

Рет қаралды 3,645

Жыл бұрын

I discovered the virtues of an electronic edge finder. I spent the money for a good quality Fowler unit that has imperial dimensions: 1/2" shank and .2" probe. So it works with my 1/2" collet and the math is simpler for me to work with a .1" offset.
If you are enjoying my channel - please give me a Like, Super Thanks or Subscribe, and you can support me on Patreon:
/ guymarsden
Used or referenced in this video:
Fowler Electronic Edge Finder - 0.200" amzn.to/3lrOscG
Tools I own, use in my videos and recommend (as an Amazon Affiliate, I earn from qualifying purchases.)
Lathe centering Bump Roller: amzn.to/3LnIiVq
Center finder for side of round stock (not super accurate!): amzn.to/3YZgRp4
Center finder for end of round bar: amzn.to/3ZgkOW7
Magnetic Base Adjustable Metal Test Indicator Holder: amzn.to/3JTsKI8
6 Piece Spotting Drill Bit Set, High Speed Steel, Short Length 120 degree, Uncoated: amzn.to/3YDSw7I
Taytools 1-1/2 Inch Machinist Center Finder amzn.to/3Sw1t0P
Mitutoyo Edge finder tool: amzn.to/3LinTkC
iGaging 6" digital caliper: amzn.to/3yHg8x5
7 Piece center drill bit set: amzn.to/3mqSIZT
Grizzly wiggler/center finder 5 piece set - for insides of circular holes: amzn.to/3IAmLpM
Bahco Smooth Cut Lathe File: amzn.to/404vVCC
3pcs 3/8"/10mm Shank Indexable Carbide Lathe Turning Tools Insert Holder Bit Set: amzn.to/3CS95nK
5Pcs 3/8" Inch Indexable Carbide Insert cutters with TCMT110204 Carbide Inserts: amzn.to/3WeZmyW
2" diameter Indexable End Mill with 3 - Tpg32 Carbide Inserts, 3/4" Straight Shank: amzn.to/3GNLbuH
Ball Turning Attachment For 7 x 14 / 7x16 Mini Lathe: amzn.to/3ZDscf3
2" Boring Head R8 Shank 1/2" Carbide Boring Bar Set: amzn.to/3J1wGpQ
Keyless 1/32"- 5/8" Drill Chuck with R8 Shank Adapter: amzn.to/3CTUetb
3 Spring Caliper set 8" / 200mm - Inside/Outside/Divider: amzn.to/3H79nts
Sewing Machine Light LED Light with flex gooseneck: amzn.to/3XyhHrv
Deburring Wheel, Nylon Fiber Buffing Polishing Wheel 6 inch 9P Hardness: amzn.to/3XlIzLN
Thrust Needle Roller Bearing with Two Washers 1/2" (for mill spindle nut): amzn.to/3CS65bg
Metric M42 8% Cobalt Twist Drill Bits Set for Stainless Steel and Hard Metal (1mm-10mm/19pcs): amzn.to/3HjquIV
Shars DRO for mini-lathe Z-axis (carriage) position. (You can cut down the 24" capacitive scale - it's aluminum.): amzn.to/3fjOfFw
Digital tachometer: amzn.to/3UePGUg
FLEXBAR Optical Center Punch: amzn.to/3WRwpKD
IRWIN Step Drill Bit Set (I highly recommend Irwin brand step drills. They were the originator of this concept in the 1980s and the knockoffs are not nearly as good) : amzn.to/3hv4zno
Angel Eye Ring Light (for mini mill): amzn.to/3fp5hSy
DC motor speed controller (for mill table feed and mini-lathe carriage): amzn.to/3WOhOjk
Brownell Oxpho-Blue Professional Grade Cold Blue: amzn.to/3TtslyX

Пікірлер: 14

@Michel-Uphoff Жыл бұрын

Guy, actually using a collet or a chuck of whatever with or without (much) run-out mostly doesn't matter when using a rotating edge finder. It will run true to the rotational center of the spindle. So, if you want to find the center of your work piece (splitting the difference between two measurements), this will work perfectly. However, not rotating the digital edge finder results in a measurement error in this case (finding the center) if the edge finder is not exactly in the center line due to (minor) deviations of the chuck, collet, etc. A mechanical edge finder will show a sudden shift opposite to the rotation when the friction between the work-piece edge and the finder is higher than the friction between the finder point and its base. That is a tiny force, so the finder just touches the edge. If used in this way I am sure the mechanical finder is superior to this not rotating 'digital' solution when it comes to finding the exact center between two measurements,

@GuyMarsdenMakesStuff Жыл бұрын

I understand and agree, but I measured the run out of the Fowler unit at .0003" in my R8 collet, so non-rotating measurements are as accurate as I need them to be on my machine.

@taranson3057 Жыл бұрын

I like both versions of edge finders that you showed. I just prefer the Starrett brand myself. I have yet to try the light switch version, may have a look into that. I have used a diy electric contact edge finder on my home built CNC machine, no lights but it sends the 0.00 position signal to the controller and it will automatically check all 3 axis in both - and + locations.

@GuyMarsdenMakesStuff Жыл бұрын

I think I may alternate between these two depending on the application...

@taranson3057 Жыл бұрын

@@GuyMarsdenMakesStuff if I ever convert my mini mill to CNC I will most definitely use the device that I made for my CNC router because it is extremely accurate

@GuyMarsdenMakesStuff Жыл бұрын

@@taranson3057 I measured the run out of the Fowler unit at .0002". I call that pretty good accuracy!

@taranson3057 Жыл бұрын

@@GuyMarsdenMakesStuff I would hope so :-)

@shawnmrfixitlee6478 Жыл бұрын

I have been meaning to get one of those , Not sure if I should get the beeping one with the LED or this one you show ? I have an old spring loaded one that works but I like the tech of that style..

@GuyMarsdenMakesStuff Жыл бұрын

I considered one with a beep, but one of the reviews said that it was a really annoying sound.

@shawnmrfixitlee6478 Жыл бұрын

@@GuyMarsdenMakesStuff ah yes , I could see that being an issue while trying to concentrate on the job at hand ..

@poorboy6988 7 ай бұрын

But whats the repeatability ? Isn't that the most important thing to understand here ?

@GuyMarsdenMakesStuff 7 ай бұрын

Absolutely. I think it's more about personal style though. I like blinky lights more than I do wiggly bits.

@bobweiram6321 Жыл бұрын

I don't bother with edge finders. I chuck a short precision ground rod and hook one end of my multimeter's alligator clip to it. I hook the other lead to the part and set the multimeter to continuity mode. I slowly creep the table until the multimeter beeps, meaning the rod contacts the part completing a circuit.

@GuyMarsdenMakesStuff Жыл бұрын

I don't understand how you are electrically isolating the part. A continuity meter would measure a connection before you touch the two parts because the whole Mill and vise etc are connected.