How to quickly Disassemble and Reassemble the Ruger LCP Pistol
Пікірлер: 177
@Theywaswrong2 жыл бұрын
DO NOT pull the trigger after you rack the slide to to check the chamber to make sure it's unloaded. The internal hammer is in the cocked position and out of the way of the slide when you go to reassemble your Ruger. If you pull the trigger before disassemble, the hammer is in the up or "fired" position and you won't get the slide to go all the way back on. You will have to manually, with your finger, push the hammer back into the cocked position to get it out of the way. I learned this the hard way. Disassembly.....rack the slide, engage the slide "lock" to inspect and insure the pistol is not loaded, release the slide lock....DO NOT PULL THE TRIGGER!!!!!!. As you see here, remove the pin, clean and lub, reinstall the slide..reinstall the pin. If the pin seems to fight back, tilt it down a bit, put a slight bit of pressure down on the end of the pin while pushing it in. Don't pull the trigger. He didn't of course but didn't mention this..leave the pistol cocked.
@edpaskan7012 Жыл бұрын
Thanks for this note. I couldn't reassemble mine and that's why I got you tube!
@chanakasgalindo6229 Жыл бұрын
I still can’t reasemble mine , i did pull the triger and i tried everything and it will not go back please help me
@astroventure2221 Жыл бұрын
@@chanakasgalindo6229I don't know if you got it resolved. When it's disassembled you have to manually cock it and there will be two clicks. Then you can reassemble.
@jackk098 ай бұрын
HA HA got on YT to figure out how to reassemble because it would not go back together, this saved me from overreacting, ha ha. THANKS
@farrisdiogenes2716 ай бұрын
Lmao thanks I already made the mistake 😂😂😂of
@sebastiangraham0014 жыл бұрын
Great video, clear speaking, simple instructions. Even 3 years later this still helps people out. Good vid
@CryptoMineLLC3 жыл бұрын
Much appreciated!
@swiftshift37802 жыл бұрын
5years later. Still helping out. Thanks!!
@paulntx Жыл бұрын
Keep it short and to the point without annoying music. PERFECT video.
@AngelOrtiz-nu1pl3 жыл бұрын
Thank you ;You make it so simple . I have my first Ruger 380 and I love it .
@sirvilhelmofyonderland6 ай бұрын
Thanks for the video. Just cleaned mine while watching. I’m an OTR truck driver and carry my .380, it gets abused. Developing rust on exterior. But cleaned it up with oil and metal brush. I love my little.380. I have a Glock 23, but it’s so big and blocky , can’t really conceal it.
@matthewwilliams17093 жыл бұрын
Thank you for the video. I was reading about how to disassemble and clean my Ruger LCP but I’m more of a visual learner. This helped me out tremendously.
@davidrudolph28252 жыл бұрын
This is an excellent video! Short and to the point with good instructions! I just purchased one of these pistols and this has been very helpful indeed! Could not be any better!
@Cmagic6785 жыл бұрын
My takedown pin was very difficult to remove. You mentioned that you don't have to pull the slide back but in other vids they say to pull back like a 1/4 inch but that seemed to work just fine for you. It didnt seem like pulling the slide back relieved tension on the spring as they claimed. It appears it wont hurt anything by not pushing the slide back..
@quickhondaz4 жыл бұрын
Nice, quick and to the point video. Thanks for the insight.
@justaguy4real3 жыл бұрын
I concur
@guerinquedens9642 Жыл бұрын
Thank you for the step by step. Short and to the point. Bravo Zulu!
@joemostaccioli2433 жыл бұрын
This is the 3rd and easiest way to dissemble the LCP. Thanks, Guy!!
@CryptoMineLLC3 жыл бұрын
What are the other ways? I'm always open to learning more!
@daequanshambley162119 күн бұрын
Proper gun safety, good explanation, and to the point. Good video
@jacobduhthrowbak32263 жыл бұрын
So simple and helpful, thank you. Love these little LCPs, they're very solid.
@matthewwilliams17093 жыл бұрын
I love mine. Just a well built little gun. Racking the slide was difficult on mine until I cleaned and oiled it. Does it a bit easier now.
@oldcop183 жыл бұрын
Good video but I have one observation: You can and should take the recoil spring off the guiderod for cleaning and lubing, they’re designed to come apart. Also, there are two recoil springs, an inner and outer. Gently pull them apart and brush lightly after shooting.
@xPigger3 жыл бұрын
MY SPRINGS
@bobwh Жыл бұрын
Great, quick video. I've been learning to field strip my guns and this one is by far the easiest. Thanks!
@wildestcowboy2668 Жыл бұрын
Where are you located Robert?
@my2cents9453 жыл бұрын
FYI, that "spring" is actually a spring inside a spring. Yep, two springs. I found out the hard way.
@nickcampbell5118 Жыл бұрын
I can't get the slide back on. The spring is in but the gun won't let me put the slide all the way on
@my2cents945 Жыл бұрын
@@nickcampbell5118 Make sure your spring is seated properly. the rod the spring is on should protrude from the front of the gun just under the barrel. I reinstall the pin before working the slide backward also. Plus the slide moves easily for a short distance back then you need to put some muscle into it to go fully back. Let me know how you make out.
@nickcampbell5118 Жыл бұрын
@@my2cents945 just ended up having to cock the hammer back and it went right back on but thanks man. I'll definitely keep this in mind the next time I clean it.
@my2cents945 Жыл бұрын
@@nickcampbell5118 glad you were able to work it out.
@robbieworrell989 Жыл бұрын
This cleared up me trying to figure out what pistol was missing a spring after cleaning a few!
@ericstanford76706 ай бұрын
Thank you for doing this video it was very helpful. I just purchased one and broke it down and cleaned and oiled it for the first time. Your detailed instructions on putting the pin back in was particularly helpful.
@CryptoMineLLC6 ай бұрын
Glad it helped! Even I go back and watch this video whenever I have to clean it again.
@bernardharvey98362 жыл бұрын
This video literally just helped me out with my lcp thanks for the video
@miriamofsanik981 Жыл бұрын
Clear and concise. Thank you.
@maxinerussell68573 жыл бұрын
Thank You very straight forward
@BobSmith-zv9mi Жыл бұрын
Thanks for the great video. My wife just purchased this gun and your video helped her a lot. Thanks
@shostang4 жыл бұрын
Very simple instructions. Thank you.
@renedelavina5869 Жыл бұрын
Excellent video. Very easy to understand.
@MagicPachinko Жыл бұрын
Forgot how to take the spring loaded pin out. Thanks for your video. Saved me from trying to find my owners manual!
@ericamenace82682 жыл бұрын
Just got my gun and this definitely helped me tremendously
@AtrollLOL4Uu8 ай бұрын
Cool vid & quick to the point 💯
@Wheres-Wolfie Жыл бұрын
Thank man! Just got one! Much appreciated
@charliebravo56122 жыл бұрын
I finally broke down and got one of these. Thanks for the vid.
@terryf51312 жыл бұрын
Excellent..took mine to the range today first time..got it good n dirty...this vid is right to the point...thumbs way up..thanks!!
@thisoldbelair Жыл бұрын
Thank you! Just what i needed! 👍
@wildestcowboy2668 Жыл бұрын
Hey Biscayne did u learn anything?
@clowd993111 ай бұрын
OH WOW EXTREMELY DETAILED INFO. THANK YOU
@chadlerch733 жыл бұрын
Excellent video and presentation. Thank you!
@user-yu4on3kn5u Жыл бұрын
It still helps after 6 years
@readlorey2 жыл бұрын
That helped me a lot…looks so easy thanks
@stephenkuron69063 жыл бұрын
Good no BS video.Thank you.
@milliondolladivabritt926 ай бұрын
Awesome video, it's short and sweet. Thanks
@CryptoMineLLC6 ай бұрын
Glad you liked it!
@bmk51554 жыл бұрын
Thanks man you been super helpful
@jerrywhatsworth35898 ай бұрын
awesome , i was having one heck of a time putting the pin in , watched the vedio again , paid attention and shhazzam!!
@trtcommunity92484 жыл бұрын
Very helpful. Thank you!
@madx2r0_224 жыл бұрын
When removing my spring. The 2 springs disconnected from the rod, does the rod go through under the barrel upon racking normally or is this a malfunction in my firearm
@vapelounge6110 Жыл бұрын
Thank you, I'm used to field stripping my glocks and recently I've acquired a few smaller guns because everything I have is big full size but I'm just used to mainly glocks and this lil Smith and Wesson shield 40 I got but I recently acquired one of these superrrr tiny lil ruger lcp 380s just because why not? And bc it was on sale brand new at my favorite local gun store I buy all my guns from for the most part and I went browsing a few days ago and the owner John that hooks me up sold kt to me brand new for 180 plus tax and gave me 100 rounds of fmj plinkers and 2 boxes of my fav self defense Hornaday critical defense hallow points along with a extra new OEM magazine for it all for free (ammo and mag) whixh is all basically why I bought suck a tiny gun that barelyyy fits my big ol paws lol... but I like to know my guns before I go shoot them and I always field strip them before I WILL go shoot them and wasn't sure as how to field strip it. This was the firdt video that popped up on how to do so and it was quick and straight to the point and very helpful... I saw a little "upgrade on Amazon for it that replaced the pin you have to pry out its got a slot for a flat head screw driver you just turn counter clockwise and it comes out just a tiny bit once you do so you don't have to put a flathead screw driver up against it and risk ruinin ur slide and scratching it up, it was only 15.99 so I think ima order it now but thanks for this video because I was kind of at a loss as I am used to what I'm used tk which is glocks but thanks for this helpful video that was short sweet simple and straight to the point.. now I can finally run it tomorrow at my range at my house... thank you for taking the time to make this video for guys like me thay don't believe in reading manuals lol.... and is too caught up in their ways on how disassemble other brands of firearms as tbats all they primarily know and own! Thank you
@Azazel7773 жыл бұрын
I liked how easy he made it should make one on how to clean it
@218Mike4 жыл бұрын
Big thanks for sharing your knowledge!
@CryptoMineLLC3 жыл бұрын
Glad it was helpful!
@karimmuhammad23066 күн бұрын
It did help! Thank you brother
@trustbanker3 жыл бұрын
Helped a lot, thanks. One thing, it took me a couple times watching you to see that you pushed up on the lock to keep the slide open. Just got this gun from a relative with no instructions with it or from him. Thanks
@CryptoMineLLC3 жыл бұрын
I'm sorry I didn't explain that part better.
@bmack29383 жыл бұрын
An automotive trim bar works well for removing the pin. Got a set for a few bucks at harbor freight.
@banditthesiberian8156 Жыл бұрын
My guide rod springs come apart to polish them and clean them they definitely come apart just make sure the big spring goes over the little one
@tomtimcik42642 жыл бұрын
Great video very helpful.
@tonyguevara48833 жыл бұрын
Awesome video
@kingtut83812 жыл бұрын
GREAT TUTORIAL
@lopsidedlobster88693 жыл бұрын
Thank you, had to disarm my stepmom. Quick and easy guide
@Ferretsnatcher3 жыл бұрын
Ah the old disarming of the stepmom. Hate when that happens. Soon it will be mother in laws
@Dethflash2 жыл бұрын
Thank you for this video
@irafowlerjr.7492 Жыл бұрын
Thanks, very helpful.
@bmack29383 жыл бұрын
I removed the spring, barrel and it still won’t slide all the way back.
@TannerisSmol972 жыл бұрын
Git gud
@bmack29382 жыл бұрын
The trigger was preventing me from getting the slide back on the frame.
@chanakasgalindo62292 жыл бұрын
Wow good video very simple
@Rocknranchman3 жыл бұрын
Great fast tutorial! Thanks for posting it!
@CryptoMineLLC3 жыл бұрын
Glad it was helpful!
@kracksmith4ejm12 жыл бұрын
does that pin ever get loose over time and fall out when shooting often or when the time is needed ?
@timhallas42753 жыл бұрын
What if I want to clean the carbon out of the firing pin bore, and the mag-well?
@TroyVD2 жыл бұрын
Thanks for this.
@bmack29383 жыл бұрын
Use a trim bar to remove the pin. They are made of plastic. Typically it’s a tool used to disassemble car dashboard stuff. Maybe remove a radio or something you don’t want to damage. Trim tools are ridged but still they don’t screw up the finish.
@markleng67 Жыл бұрын
Thanks! gOOD JOB!
@lynnthain3803 жыл бұрын
Great job
@364pgr3 жыл бұрын
Thanks, helped alot
@mikepks3 жыл бұрын
Thank You for Sharing.
@AZ-Ron2 ай бұрын
Very helpful!
@fiermonte833 жыл бұрын
Thank you!! 👍🏻
@casperburgos10662 жыл бұрын
AWESOME Thank you
@TheTedkorn2 жыл бұрын
Nice one, thank you.
@CryptoMineLLC2 жыл бұрын
No problem 👍
@MyMotorcycleObsession2 жыл бұрын
Thanks man!
@justaguy4real3 жыл бұрын
1:25 wonder if there's ever much issue with swapping barrels and gun itself, basically differing serial numbers
@CryptoMineLLC3 жыл бұрын
I wouldn't think so. But I've never tried it.
@juanitoaguilera37293 жыл бұрын
Thanks bro good info 👍🏼
@CryptoMineLLC3 жыл бұрын
You bet
@seven7seven2 жыл бұрын
Thanks!
@gdmofo11 ай бұрын
Muy bueno gracias
@jerrywhatsworth35898 ай бұрын
Thanks gin!!
@lead5s2 жыл бұрын
Thank you
@bud29353 ай бұрын
Thanks! 👍👍
@GladishR Жыл бұрын
Does the Ruger 380 LCP ever have two springs?
@jdmbraceyourself695 Жыл бұрын
Thanks
@ccross156 ай бұрын
Took mine apart. I feel like i re assembled it correctly... but now when I try to chamber a round it isn't smooth and seems jammed a bit and I have to really work to get the slide back and a round chambered...any tips?
@CryptoMineLLC6 ай бұрын
I would try it again to confirm everything is seated properly and inspect for any gunk that may remain along the slide guides. Confirm the feeding ramp is also looking good.
@spacedaddycereal734 жыл бұрын
Had issuses slide pin back in
@user-hx5vh9uh2n2 жыл бұрын
Thanks I just bought a used one off a cop in my town. Since it’s off roster in California
@mgtrev75572 жыл бұрын
ty 🙏
@gusolascuaga26662 жыл бұрын
I was wondering does your barrel move around slightly up and down
@stoneblue17952 жыл бұрын
It will when the action is open, certainly.
@garyellis1862 Жыл бұрын
Thk u
@jimmywilliamson85402 жыл бұрын
It's nice that everything John Brown indeed has lived on in a 1000 different in different, probably more like 50000 different versions. But but oh my goodness every time I take this thing apart I have to remind myself I'm not actually breaking it.
@bmack29383 жыл бұрын
My LCP won’t slide all the way back. It falls short maybe 3/8”.
@kylestengl86053 жыл бұрын
I had the same issue on mine, something weird with the firing hammer getting in the way. Had to pull the trigger to put it down to slide it over, then pull back after I got it past a point, otherwise if I forced it it still made the firing hammer go down. Hopefully you've figured it out after 2 months!
@charlesromano35733 жыл бұрын
I have a live round stuck in chamber slide only moving a little how do I get the live round out
@stevemaslow7032 жыл бұрын
carefully push it out with a wooden dowel rod or a cleaning rod
@wildestcowboy2668 Жыл бұрын
My slide want stay back and today I pulled the trigger and it didn't shoot once
@user-hx5vh9uh2n2 жыл бұрын
Anyone used a QuickDraw clip on their .380 though or maybe adding one but think maybe it will be hard to draw and stick to firmly To belt or be too Deeply concealed to get to. Other thing someone told Me was body oils will ruin it if it’s in waist against skin.
@robertw.67534 жыл бұрын
Good video! I am having trouble with my newly acquired Ruger. In the final stage of reassembly, I cannot get the pin back in. Any suggestions would be appreciated.
@usmczippoguy79474 жыл бұрын
I"m sure you haven't been waiting three months to figure out how to put your gun back together haha. But as you have already figured out it won't go all the way back in without pulling the slide just a tiny bit.
@jlynne.74 жыл бұрын
@@usmczippoguy7947 thank you 😁
@rJayisawesome4 жыл бұрын
I found pushing a little back on the slide (1 finger on the front near the muzzle will do) while pushing it in at a slight downward angle does it.
@thejohn66143 жыл бұрын
How to you get the back pin back in?
@stoneblue17952 жыл бұрын
Line up the holes, push through.
@richardrogers82543 жыл бұрын
That pin is probably designed to be removed with a brass 9mm round rim.
@jessepollard38443 жыл бұрын
What causes a round to not feed into the chamber on the LCP?
@CryptoMineLLC3 жыл бұрын
Try giving the feed ramp a good cleaning and a touch of lubrication. If that doesn't work, try different ammo or magazine. Lastly, take it to a local gun smith because beyond that I am not sure.
@stoneblue17952 жыл бұрын
Polish the feed ramp with some "Flitz" or similar polish till it looks like chrome. Small dremel cone shaped cotton "buds"- Amazon sells some generic ones that are fine.
@theoppiesghost3 жыл бұрын
The follower on this clip works just as well as a screwdriver
@Jeslmcg3 жыл бұрын
How can you make the slide easy to slide
@CryptoMineLLC3 жыл бұрын
You ban purchase a different spring but I don't know what all is available.
@DARTHDANSAN8 ай бұрын
Thanks from the future 😅
@gunssavedicks3 жыл бұрын
Is there any way i can contact you?
@gabrielxorta4 жыл бұрын
my chamber does not slide in all the way. any ideas????
@RetiredUSArmy14 жыл бұрын
Did you fix it??? I’m having the same problem
@gabrielxorta4 жыл бұрын
@@RetiredUSArmy1 yes sir i put it on the rail and slide the chamber back and lined up the pin with the hole
@RetiredUSArmy14 жыл бұрын
Gabriel orta thanks I had to learn the hard way too
@gabrielxorta4 жыл бұрын
@@RetiredUSArmy1 yeah it was rough
@TheSpencer00003 жыл бұрын
good video. I wish you would have removed the live ammunition from the room.
@calebkencel40183 жыл бұрын
Why?
@zarinkai29273 жыл бұрын
@@calebkencel4018 he could've shot us through the screen 😆