Raijintek Morpheus 8069 and HP Omen OEM RTX 3080 Install and Performance

Рет қаралды 11,746

Жыл бұрын

In this video I install the Raijintek Morpheus 8069 on the HP Omen OEM RTX 3080 10 GB GDDR6X to try and tame the (up to) 80 C temps I was seeing while gaming (this card doesn't have a great cooler as you'll see). The 8069 added substantial cooling performance to the card paired with a couple of be quiet Silent Wings Pro 4 120mm case fans. I also used 2 Gelid Solutions PWM Fan adapters for VGA cooler fans as this card has 2 fan headers on the PCB. For the work, I used the iFixit Pro Tech Toolkit. The Morpheus 8069 was purchased from grooves.land for $144.86 but can be found on Newegg and Ebay.
Songs in order played:
Architect of the Future, In the Atmosphere - Bad Snacks, Infinite - Garret Bevins, Rainbow Youth, Inspiration, Red Tape, Kaleidoscope

Пікірлер: 48

@krunchy1736 Жыл бұрын

This is the weirdest and intriguing 3rd party cooler I've seen. It's neat to see a heatsink instead of watercooler setup though, especially because it seems to be pretty effective. Also I just want to say that when putting thermal paste on a gpu die, it is pretty important to get it all covered. Unlike a cpu with an IHS, the gpu die is just exposed so any spot that's not covered will get hotter. BUT yours seemed to spread evenly enough to keep it stable so good job!

@bradeinarsen Жыл бұрын

Super nice demo vid. Thanks! And the numbers at the end!!!

@JustinCrediblename 8 ай бұрын

damn that was impressive

@g1g3l 6 ай бұрын

I have an XFX Merc 6800 XT. It's about 8 months old since I got it, but after seeing this video, you made me consider butchering the card and void the warranty for that nearly 20 degree reduction. Wow

@0BuLLeT01 Жыл бұрын

I've just ordered one of these to replace the awful blower style cooler on my Gigabyte RTX3090. I've had to underclock it by 50% to keep the noise levels tolerable. I'm hoping that this will be a good solution. My case is windowless, to aesthetics don't matter at all to me. Going to have to choose fans and adapters though.

@yanagida_01 Жыл бұрын

might as well go for noctua chromax fans for them? or if you're on a budget maybe the deepcool fk120's would be a decent option, since the arctic fans have this weird humming sound at 1000rpm+

@cameronadams3456 Жыл бұрын

@@yanagida_01 Which arctic fans? My arctics only hum around the 1500 to 1750 area.

@Erksah68 9 ай бұрын

@@cameronadams3456p 12/p14

@vubobanh Жыл бұрын

Video is much appreciated. I wanted to jerry rig a 8068 (10 series variant) on the 30 series a while back. A lot of custom work but appreciate the company offically releasing new one. Question, would you try Noctua A12x25 for accoustics and performance?

@dockbock Жыл бұрын

I know I bought those expensive Be quiet fans, but I don't have the disposable to pick up fans that I don't need at the moment. Performance wise though, the Silent Wings Pro 4 have a peak cfm (cubic feet per minute) of 84 and a static pressure of 5.31 mm H2O at 36.9 dB while the NF-A12x25 has a peak cfm of 60.1 and a static pressure of 2.34 mm H2O at 22.6 dB. (That's from the manufactures websites) so with the higher rpm you will get more fan performance at the tradeoff of considerably more noise. Granted the Silent wing pro 4s are not particularly audible from within my case, and also you really don't need too much fan anyway.

@suspensefulmusic9794 10 ай бұрын

I am thinking about doing the mod as well with my HP 3080ti. Right now i simply have 2 P12s strapped with zipties on the original cooler. I'd like to know if you tried to keep the original metal bracket or is it to thick to fit under the VRAM Cooler of the 8069?

@dockbock 10 ай бұрын

My structural bracket had to go because it was passively cooling the VRAM chips and mosfets (poorly) and the 8069 would not physically be able to fit.

@chincemagnet 9 ай бұрын

Maybe I should have gone this route, considerably cheaper than liquid cooling, although I went cheap as possible on this loop I have yet to build, waiting on pump reservoir, which for whatever reason hasn’t shipped after 6 days

@ZoruaZorroark 23 күн бұрын

i doubt it would have any positive effect for my evga 3090ti ftw3 ultra, but i am sure there is something (outside of watercooling)

@MechAdv 9 ай бұрын

I was so excited when this finally dropped because my Gigabyte Gaming OC cooler is loud as hell and barely keeps my 3080 in the mid 70s in an air conditioned room, but 170$ for a heat sink!? Got damn that’s double the price of the old one!

@dockbock 9 ай бұрын

Steep, it cost half the price of the card I put it on, but there isn't much option other than custom liquid cooling which is also pricey.

@ZenTunE- 5 ай бұрын

Interesting improvement. My Zotac 3080 heatsink seems pretty good though, I run 3 92x25mm noctuas on it and at 40% (~750rpm), they can keep it the core at 80°C while pulling 270W. (Probably ~60% for 330W.) So your stock cooler doing as high as 78°C with those insane 3500rpm fan speeds seems really bad? I don't remember but I think if I ran the stock zotac fans at 100%, the card would stay below 70°C 🤔

@dockbock 3 ай бұрын

Yes, the stock fans only seemed to be giving diminishing returns on cooling past 2000-2500 RPM.

@lions7staso Жыл бұрын

Hello, Im planning to do the same for my RTX 3080 SUPRIM X. Can you tell what is the thickness of the memory pads ? I want to put Gelid GP-Ultimate.

@dockbock Жыл бұрын

The memory thermal pads have a thickness of about 2.25mm.

@theraven26780 9 ай бұрын

to remove that stuff from vrams use a pencil eraser itll rub it off quite fast

@technicallyoverwhelmed2948 10 ай бұрын

Why did you need a adapter for the fans to install it on your GPU? isnt it a 4pin PWM anyway?

@suspensefulmusic9794 10 ай бұрын

GPUs have a different connector than the mainboard PWM fan header. Its the JST PH 4 Pin connector. The sigal is the same. But with a program like Fan Control, you could let the the mainboard and software control the new GPU fans. Especially because the middle fan of the HP card cannot be controlled directly with afterburner.

@virxest 11 ай бұрын

Can you turn the fans down to ~1000rpm and still play under 90c?

@dockbock 11 ай бұрын

The short answer is likely yes. Fan blade geometry and blade number will vary results, but with the Silent Wings Pro 4 (at the lowest I could make them in Afterburner 1250 RPM) adequately cooled the GPU die under 100% load to 76 C with the hot spot 86-88 C. The VRAM however ran around 94-96 C, which is still in spec of the 105-110 C throttle limit. I also forgot I had a 180 Mhz overclock on the core and 500 Mhz overclock on the memory which does, of course, increase temperature.

@sayacee5813 Жыл бұрын

im using dell 3080, the stock cooler is fine until im running raytracing stuff. deshroud it with p12 max and the issue is solved. non raytracing temp is mid 60 while raytracing is low 70

@sayacee5813 9 ай бұрын

@@NaanKartik 3080 is a hot card, do the thermal paste mod on ur dell gpu too

@happybuggy1582 6 ай бұрын

Wish they made a 360 one that would slow down the fan by even more

@chrisz5z 6 ай бұрын

The temperature drop probably had more to do with the original thermal paste being dried out. However, looks like it'd be a worthwhile mod for the noise alone 👍

@Takashita_Sukakoki 5 ай бұрын

I own the card and the cooler is just too light weight to deal with 320w. theres a reason there are 3 super loud and fast fans on it. Even putting 2 noctuas on it at 1500rpm cant keep up...

@VANYA884 9 ай бұрын

hi my vantus 3080 noctua mod in game 70c chip 90c mem 1200rpm 320w, stok 68c chip 88c mem 1800 rpm 320w, 2800 rpm over curva sheit

@TurboD16z6 11 ай бұрын

Will this work with 4090?

@dockbock 10 ай бұрын

From what I've heard I don't think it will be your best bet for the 4090 though I believe it will mount up.

@LuiFernando-fi3om 6 ай бұрын

i think the fans are in the wrong position. you put them to release air to inside the graphics card instead releasing the air to out side of the card

@happybuggy1582 6 ай бұрын

Every single card ever made is blow in type😂

@g1g3l 6 ай бұрын

The fans are correct. Air is supposed to be blown into the fins of the cooler.

@Takashita_Sukakoki 5 ай бұрын

Blowing air over the board is optimal for the VRM components

@nicklasrunesson993 Жыл бұрын

Be careful when you buy this cooler i have it and use it on my amd rx 6800 xt and Cooler does not fit! I was forced to mod this cooler and cut off a bit of it. Left side of gpu die on this Cooler i was forced to cut off a bit.

@gabrielst527 Жыл бұрын

Yeah they are made for base version of the GPUs not aftermarket, so they will have some modifications needed in base of the type of card picked.

@vubobanh Жыл бұрын

Don't think it's made for reference model 30 series. The FE ones have a unique power connector for its fan. For a while, if you ripped that cord, it was really hard to get a replacement.

@PREDATEURLT 11 ай бұрын

@@vubobanh this cooler doesn't need to be connected to GPU, can use motherboard or PSU connections (fan control will not work according to GPU temp).

@chincemagnet 9 ай бұрын

Music too loud (imo 🤷🏼)

@Takashita_Sukakoki 5 ай бұрын

Really suck the HP 3080 card has a hard BIOS limit of 320W and minimum fan speed of 30%. Ironically undervolting gets you more power/frequency headroom. I own the card i deshrouded it and zip-tied noctua NF12s on it connected to the mobo and controlled by Fancontrol v144 in the OS and undervolted to 0.9V @1845mhz . It no longer sounds like a jet engine but still maxes out the noctuas at 1500rpm and can reach 84C. The default cooler is built on min-maxing off the fans aka minimum amount of cooler mass to maximum fan speed just to barely hold it in spec. The morpheus 8069 at 145€ could buy you a better cooled card. Its cool for tinkerers but the price to performance isn't really there.

@dockbock 3 ай бұрын

This is a fair point. For now the cooler will serve for the longevity of the card but it also adds the cooling over head for power modding the card (though I will need take a look at the VRMs to see how much they can take).

@Takashita_Sukakoki 3 ай бұрын

@@dockbock sticked arctic p12 max that go up to 3300rpm on em now we cool

@dreamseeker9207 10 ай бұрын

2800rpm 120mm fan is super loud man.

@Ladioz 3 ай бұрын

2800rpm loud on anything is loud. there is no gpu fan or case fan that can make 1500 + RPM quiet or tolerable..

@dreamseeker9207 3 ай бұрын

@@Ladioz I had 6800xt red devil 1500 rpm was super quiet now have 7900gre sapphire pulse and is same, and even i need to put them on higher rpm becouse on stock workin on 1100rpm xd, so i put them exactly to go on 1500-1600 and is nice.