BUILD CHEAP BELT GRINDER

Рет қаралды 131,318

3 жыл бұрын

#BuildCheapBeltGrinder #JhonArief
Today I made belt sander with cheap materials that I bought at scrapyards , I use 2 inch pipe, 2 pcs of bicycle Axle bearing hub, 5mm thick steel plate and cheap bench grinder.
it's very easy to build but mostly is metal working job, only 20% woodworking.
I hope you guys like this project and get inspired
Email : jhonariefdiy@gmail.com
Page : / workshopjhonarief
Backsound : www.bensound.com

Пікірлер: 73

@antoniodeoliveira1849 2 жыл бұрын

Thanks for giving measurements for those following your video makes things a lot easier

@avizomedeo5178 3 жыл бұрын

Thank you for the computer graphics. Makes understanding easier!

@klave8511 3 жыл бұрын

When welding something with bearings, don’t let the weld current flow through the bearings. Connect the ground clamp to the same piece you are welding or the bearings get damaged.

@jhonarief 3 жыл бұрын

Thanks for this nice info, will note that for next weld project 👍

@AubMar 11 ай бұрын

I was just about to say exactly that because the current will arc and pit the surfaces, and fail prematurely. I know because it happened to me once upon a time!

@user-davidben 2 жыл бұрын

נהדר עבודה טובה..אתה איש מוכשר..כל הכבוד..

@brucewaynehdl6388 3 жыл бұрын

Excelente trabajo te felicito 👍👏👏👏

@anglerweekenderrizalzi3419 2 жыл бұрын

nice share and tutorial, thank you

@eddiewalker4530 Жыл бұрын

Nice work, great video and graphics

@hossamninga7388 3 жыл бұрын

Good job thankyou

@restorationfr2098 3 жыл бұрын

good job

@scottpelka1211 3 жыл бұрын

Hi... nice job. One comment I would have is make the table for the sander higher so if someone wants to grind something it can be done from the right or left side wants to sand a long piece like a knife or other item.

@bryanverran8841 Жыл бұрын

Thanks

@nissanzargari 3 жыл бұрын

Very nice job ,weldone from israel

@jhonarief 3 жыл бұрын

Thank you

@sigung01 3 жыл бұрын

Brilliant

@jhonarief 3 жыл бұрын

Thank you

@skoparweaver7692 11 ай бұрын

Careful wearing gloves around rotating machinery like a drill press - it's a great way to lose a hand or get dragged into the machine. Other than that - great build and you've given me some ideas.

@valeryn4704 2 жыл бұрын

Hello. The part that serves to tighten the belt (a gas stop rests against it and a tensioning roller is installed on it) - why is it fixed on the main rack close to the moving tape, and not along the axis of the main rack and not closer to the tensioning roller. Is it caused by something?

@woodstory1771 3 жыл бұрын

Lagi dan lagi... Kayaknya uda lumayan banyak ni fans luar nya

@jhonarief 3 жыл бұрын

Berkat semangat sama doa om, ayooo om juga bisa... Yg penting semangatnya jangan kendor, kan udah ada laptop pendukung nih, semangat ya om

@woodstory1771 3 жыл бұрын

@@jhonarief Siap Om tx Support nya

@tomayrscotland6890 3 жыл бұрын

Hi Fella' what animation program are you using?. Tom Scotland. it looks just great to use. Ps the bench grinder is just tops too. thanks for the video.

@jhonarief 3 жыл бұрын

I use sketch up, thank you

@sangteahauhnar5482 2 жыл бұрын

A tha hle mai, minlo siam sak ve ka pu

@mehdibehroozpour332 11 ай бұрын

ممنون.از روی همین ایده یه سمباده نواری ساختم🙏🙏

@mehdibehroozpour332 10 ай бұрын

آره خوب بود منم سنگ سمباده داشتم از روی همین ایده تبدیل به سمباده نواری کردم

@user-ff8ui1to5w 2 жыл бұрын

Отлично 👍👍👍

@dragonUSNr 3 жыл бұрын

Great video!!! What size belt is that?

@jhonarief 3 жыл бұрын

4 x 36 or 100 mm x 915mm

@a.cotrimluis7580 Жыл бұрын

👍🔝

@dougi2dope 3 жыл бұрын

How strong is the gas strut? Different one lift different weights!

@jhonarief 3 жыл бұрын

If you look at mine is 150N is little bit to much force for this belt grinder thats why I recomended buy 80N gas spring . that because if its to strong then the tension will be more and belt grinder sound will to loud because amount of pressure at the bearings

@xavierdesaegher7353 3 жыл бұрын

Wonderful and your explaination are as well

@jhonarief 3 жыл бұрын

Thank you, I'm glad that you like it

@makermaniacdiy 3 жыл бұрын

ottimo lavoro complimenti, lo condivido sul mio gruppo

@jhonarief 3 жыл бұрын

thank you so much for sharing my content

@alrubaye81 2 жыл бұрын

بماذا يمكن ان اعوض ذراع الهايدوليك الذي وضعته ؟ لاني لا املك واحد؟

@Im_Still_LightSpeedLayne 3 жыл бұрын

Good job. Might I give one small piece of advice. Maybe not use a tack hammer to center punch. I know it’s nit picking and maybe it’s the only hammer that you have. Not trying to be a douche bag, just tryin to help. Anyway, great video. And I liked that you edited in the plans throughout.

@jhonarief 3 жыл бұрын

Thank you so much

@gcfrede 3 жыл бұрын

You should not weld galvanized steel, its toxic :( other than that good idea :)

@emmalelef8952 Жыл бұрын

Please how to get the plan ?

@bennyhartono4742 3 жыл бұрын

Do you make the sandpaper yourself?

@jhonarief 3 жыл бұрын

Yes, wow how you notice that? I will posted how to have strong joint that sand paper on my next project

@bennyhartono4742 3 жыл бұрын

@@jhonarief i can't wait to see that👍

@jhonarief 3 жыл бұрын

But dont worry this diy belt sander can use common belt sander on the market with size 4x36 inch / 100x 915mm there is available at home depo

@jhonarief 3 жыл бұрын

Wait on next sunday I will posted for you, Thank you for stay tune at my channel, cheers

@howardsnyder7402 3 жыл бұрын

I hope you are using cutting oil, NOT WD40, for drilling.

@sangteahauhnar5482 2 жыл бұрын

Phaileng lamah pathum minlo thawn thei a ngem

@muhiddinnuriddinov68 2 жыл бұрын

Скажите мне пожалуйста... Зачем делать на двух роликах когда можно сделать на одном ролике 🤔

@Kebekwoodcraft7375 3 жыл бұрын

I never use cutting oil for drilling I think it's over use !

@alk5749 2 жыл бұрын

wouldn't want to use any of your dull drill bits, and yes without some sort of cutting oil you reduce the bit life by a lot.

@Kebekwoodcraft7375 2 жыл бұрын

@@alk5749 I have to say my drills bits are very sharp it’s what I mean you presume cause I don’t use oil they are getting bad !

@Kebekwoodcraft7375 2 жыл бұрын

@@alk5749 it’s more about speed and pressure !

@alk5749 2 жыл бұрын

@@Kebekwoodcraft7375 speed, pressure and lubrication. The absents of any of those is failure.

@jstrndm945 3 жыл бұрын

Itu las apa namanya?

@jstrndm945 3 жыл бұрын

Boleh minta plan nya gak mas?

@jhonarief 3 жыл бұрын

Itu las mig mas

@jstrndm945 3 жыл бұрын

@@jhonarief emang ga pake besi stick yg biasa buat las ya?

@jhonarief 3 жыл бұрын

Kebetulan saya newbie klo pake stik biasa seringnya lengket makanya pindah ke las mig mas

@rijalvandry7367 3 жыл бұрын

Bsa jiplak autoplan nya mas

@jhonarief 3 жыл бұрын

Silahkan mas

@rijalvandry7367 3 жыл бұрын

Boleh mnta autocad nya mas..sya tertarik bikin juga.. simple 👍👍

@jhonarief 3 жыл бұрын

@@rijalvandry7367 saya gak ada Acad mas soalnya gak bisa pakenya, saya pake sketchup 2019 itu aja filenya cuman divideo aja file mentahnya udah gak tau kemana mas

@harisupriadi7017 3 жыл бұрын

Bench grinder nya brp pk?

@jhonarief 3 жыл бұрын

Yg 350watt

@jhonarief 3 жыл бұрын

Bench grinder yg 8 inch

@harisupriadi7017 3 жыл бұрын

@@jhonarief cukup kuat?

@jhonarief 3 жыл бұрын

Sudah saya pergunakan buat besi dan kayu tidak ada masalah om? Jgn kawatir dia rpmnya tinggi jadi ngga perlu ditekan kuat dia sudah bisa mengikis dengan mudah baik besi ataupun kayu

@harisupriadi7017 3 жыл бұрын

Terimakasih infonya 🙏