Join the Nation! www.sxsnation.com UTV News, Tech, and Giveaways!
Пікірлер: 24
@williamwhitley7969Ай бұрын
I'm really glad I watched this video, saved me a bunch of dismantling.Thanks.
@robkent6321 Жыл бұрын
Very helpful video. My Ranger only has 600 hrs on it but the u- joints were making noise and needed changed. Your method worked well and and saved dismantling the front end and taking the diff out. Thanks !
@formerlyknownas785712 күн бұрын
Thanks for the good info. Was going to remove the front diff. Saved a lot of time. The part # info was invaluable too.
@barney4532 жыл бұрын
Great instructive video! We followed it fully and the job went exactly as you described. Thanks!!!
@frankb71072 жыл бұрын
Great video TKS, Mine was a mid size 2016 570 an it did great!!
@ryansoutdoorschannel34282 жыл бұрын
Thanks for showing us how you got the pin out that’s the only problem I’m having
@michaelpavon97433 жыл бұрын
THANK YOU!!! it worked great.
@GerraldFarms Жыл бұрын
Thanks for sharing. Great instructional video.
@johnowen65075 жыл бұрын
i wonder why polaris doesn't go to a cv joint on their drive shafts. i don't know how many rear drive shafts I've replaced on dad's polaris four wheelers for that exact same reason, worn u joints and bad splines. the slop got so bad on the rear diff that i had to replace the whole thing, it just gets rust and dirt in there and wears itself out. pretty nice winter we're having.
@davide31294 жыл бұрын
Very good
@glenyukon99233 жыл бұрын
Sweet..im betting the ujoints are going out and causing the splines to go bad after. thoughts on a rubber O ring on the front diff shaft before sliding the prop back on?
@OldGlory17763 жыл бұрын
Not sure about putting an o-ring on the front shaft, there is no Groove for it to sit in. The last couple I have done the splines have stayed tight on the front yokes (rusted in) and the U-joints still ended up failing as normal. I have been able to extend the life of the rear prop shaft splined yoke by siliconing around the end of the Yoke to keep dirt and water from entering. Its helped alot.
@williamwhitley7969Ай бұрын
Considering using a bicycle tube stretched over the joint and a couple of zip ties.after I fill it full of grease!
@LittleSpragueOutdoors4 жыл бұрын
Where did you order this prop shaft from?
@wilkerandrade74183 жыл бұрын
Hi. Nice video. Where did you buy this item and how big is this peace? I trying to get one for my Ranger 570 midsize but this is so confuse. Alot different information. Can you please help me on this information?
@chasduster3 жыл бұрын
I ordered mine from superatv it’s called a front propshaft for a reg cab Polaris . It’s prob 4 feet long approx . It ain’t cheap
@robertpage29273 жыл бұрын
Mine is 2015 same problem but for your viewers drop plastic bottom shield slide back loosen 4 mount bolts on front diff . Comes out bottom
@robertpage29273 жыл бұрын
They are not fun
@joshhespen2525 Жыл бұрын
Where did you find the driveshaft? Can you post a link! Thanks
@OldGlory1776 Жыл бұрын
It's a polaris driveline
@deanlarkins5858 Жыл бұрын
But ranger has a 2 inch lift
@c6farms9525 жыл бұрын
How many miles do you have on it and how many 570 do you have
@OldGlory17765 жыл бұрын
There is about 6500 miles and 900 hours on this unit now. The other two 570s have between 600 and 800 hours, probably between 4500 and 6000 miles on them. We bought three of these 570s at the same time a year back. They were on rebate and we were able to reuse our 800 cabs on these models. so far these have been good machines, simple to service good on fuel and easy to repair. So far all three have needed a drive clutch and prop shaft at about the same miles an hours. The clutch would have lasted much longer if Polaris had put the intake for the CVT box up front like they used to. Instead they move the intake behind the seat where it picks up a lot more dust than it should
@larretta882 жыл бұрын
Ive brought mine in 2 times for broke u joints . Polaris sucks and don't fix things right.