THIS IS THE SOUND. OMG! I'VE TAKEN MY CAR EVERYWHERE AND THEY CLAIM THEY CAN'T HEAR IT. THANK YOU!

how am I only coming arose this video now after nearly a year of searching on google and KZfaq, I had already resorted to buying a new caliper from the dealership, Thanks to your video this is a simple DIY job which takes less than 20min to complete. Thanks to you my car rides like new again..... I tip my had to you sir!

Pro tip to identify if brake calper rattle. Keep brake on lightly and keep moving with gas peddle. No rattle boom you have identified problem. Seen a lot of people here confused about if it is brakes or suspension. Easy Easy

Yet another use for sticky tape! I probably won't use the tape but it did highlight that the pins (or bushes) do wear out. Thanks

Thanks! Very helpful video! I watched 3 brake replacement videos and none of them mentioned to grease the pins or it’ll seize 😅 It might be common sense for mechanics but as a complete beginner this was HUGE to solving the rattling sound. Here’s to taking my tyres off for the third time - surely a charm this time 😅

Hello, excellent demonstration video, I have an old Fiat that has been making this noise for a long time, I tried to replace the pair of 2 pins, found on Autodoc but it didn't last long, I tried the grease, the aluminum foil crumbles, I'm going to try duct tape now, it'll be fine anyway!! HI

This is a very good video you have made! Thank you!💯

It might help if you install the anti-rattle rubber ring on the tip of the lower pin.

Hi Sir..If sounds we still can drive? coz I now went out state. I scare been scamm for others problems as well. The brake have rattling sounds when press hard if press slow no sounds..

Very Infromative,Thanks

I never thought about the tape sleeve. I will try it. Great idea. Thanks.

Sir did you put tape on those pins?

I did this today then now am seeing it in replay..It was a work out... A mechanic put soda tin foil to hold the caliper pins instead of grease.. I removed them and put bees wax and wd40 and It worked well..

Ive got a similar thunk or clunk when im driving over bumps but it goes away sometimes under throttle and for sure when im braking. Took me forever to pinpoint when it did it but it always has done this since ive bought the car. Never had play in my slide pins, usually they seize up but ive replaced the entire caliper, rotor and pads and it still knocks. It sounds louder now but i think its moving less than before. It doesnt sound quite as rough anymore but its just concerning because it sounds like my calipers just loose. I think mine might be brake pad/caliper knockback. Im not that abusive on my car since its my daily but thats the only thing that i think could be it. Unless its in my suspension but i dont think it would go away under braking

Hearing a rattling over bumps. Checked it out and one of the calipers is quite loose. The other side has no play. Replace pins? I read you mentioned brackets too. Which bracket are you referring too? Where the pin slides in? I am doubtful a little clear tape will fix 1/8"+ play. But mine looks similar to your so maybe all I need is tape (anything special?) and some lube (grease work?) TY

Thanks for this video and the explanation - I have the same problem and when I step on the brakes, the rattling immediately stops - so it's the caliper (bracket?). So, can I let this go and not get it fixed or is it dangerous? I already took it to a mechanic and they can't find anything wrong with the suspension, but probably didn't check the brake caliper. How long can I let the rattle continue before it becomes dangerous or an issue?

Excellent video thumbs up!!! Please take my advice as a career mechanic - hitting that ratchet like that will give you arthritis in your pinky. Trust me.

I just did mine it was stuck know I lubricate it but the boots were broken and were not available nearby so I just lubricate it with the silicone grease which is recommended an the manual

Great one machans. This will come in very handy, in case there is excess play in the caliper or any khat khat movement from the caliper. Great one as usual.

Anyone able to tell me. i replaced hub,rotor,brakes. i am getting a tink /kinda squeaking when my wheels turned right mostly. it happen ,and go away sometimes. only full goes away when i brake. once i release the brake it goes back to a little squeak,also kinda sounds like a tink tink tink tink tink. sometimes if i hit a few bumps after a nother it will go away.. sorry for horrible description.

Bro please help me My car figo Rattling sound coming from front side I don't know actually from which part. Sounds coming only when I put 1st or 2nd gear from neutral and releasing cluch moving to forward. Reverse gear also.

Since this is just a temporary fix, what exactly would need to be replaced to prevent it from wiggling/making the noise? I’m having the same issue

My wagon r is almost 10 year old and during last service i had changed the brake calipers, but the workshop suggested replacing the brake caliper again how often does it need to be changed. My car makes a hissing sound while starting for a minute or so after running it goes off. Please suggest

I've got a similar noise coming from drivers side front wheel when driving over small bumps/lines in the road in my bmw f20 125d. I've taken it to 2 mechanics and asked them to check the suspension. They both said the same thing, suspension is fine but may be inner track rod end. Changed rod end but noise is still there. Could it be these pins? Should I take it to a mechanic and ask them to change the pins? The sound is really annoying 😒

Awesome video

Knocking noise at rear s cross what's issue

I tried that yesterday. So far i am happy

Great

Brother ive ordered new caliper pins from Amazon for my vw polo petrol 2011 model ...(kylo brake caliper pins ) and there mentioned it will set for skoda/polo/ fabia also...so is that right part it will set to my polo or not? Can i order that?

If I replace the pins would that fix the play or I’ll have to replace the caliper and pins so there’s no more play?

My 08 Chevy Silverado 2500 hd driver side brake caliper rattling but when I press the brakes it stops

Tape will melt due to excess heating from braking instead use almunium foil and silicon Grease

Buy new pins..clear tape really. You’re there and have it apart. Do it right.

I have a rattling noise when I'm hitting the brakes and going left it rattles then stops, and whenever it goes over 60 miles/hr it starts to rattle, can it be this?

What about the heat of the brake system melting down the plastic tape?

One of my breaks was rattling really bad on a brand new car. I took off the wheel and sprayed down the whole caliper with silicone spray. Now the rattling is gone. Should I still grease the pins?

Hi dear, when we hear such sound if we replace brake brackets, should we replace the pins along with it or same pins can be used. What about rubber boots n seal ?

Tnx:)

Does your brake or wheel get more hot than normal with this ammount of play? Or is it just for comfort to remove the play?

Hi Daily, I am having the same problem. When I knock the wheels, it gives this sound. I took this to a mechanic and he greased the slider pins. But after 2 days, the sound started coming again. He told me that the calliper slider pins needs changing. Will the problem be fixed if he changes the slider pins?

Bro, Are you using 1/4 inch or 1/2 inch tool kit? 1/4 inch tool kit sufficient enough for cars?

Will sticky tape really endure and not break up?

Waiting for this video... Teflon tap chuttiyitt kurach odiyappozhe veendum sound thidangi... Copper sheet vangan kore anyeshichu.. kittiyilla... Clear tap last cheyyarundo

Wont the tape melt when long braking is applied.i live in the mountains with steep roads.

👌👍

Hello, the caliper pin bolts in my alto is too tight . Am not able to remove it.. how do i do it..

I have used the same the sound has gone , but within 2 days and again the sound remains the same. My mechanic said pins needs to be welded.

Cellotape! This would melt on my first trip!

I think this is why my rear clunking noise coming from....

What are those pins called???????

so what was causing the play to begin with?

"Place caliper in secure place" *Balances caliper delicately on pipe above concrete floor* 😅

Dose the tape melt due to the heat?

Hard noise in intro, chillout in listening video?

Teflon tape works best

You put the guide on top where the rod should be. Check the beginning of the video.

why don't you use the stainless steel shim. 001" maybe better

This is the sound! I've taken my car to the mechanic and he replased the entire suspension. What a waste.

المفروض تسمعنا صوت الكليبر، وليس صوت الموسيقى... وشكرا

why you do this "hacking" when new pins with rubbers is 5-10$

Caliper bracket needs replacing along with the pins.

Tape? Really? Sacrifice the Starbucks coffee for a week to get new caliper bushings and pins. 😉

or tapelon maybe

I had this problem on my Renault Megane mk3 a couple years ago. Spent so much money on idiot mechanics that didn't fix the problem or even know what was up. Replaced the slider pins and my clunking nightmare went away. Yesterday the clunking came back. Guess I'll have to repeat the process.

I have read we use special silicon grease because of heat. You used tape to minimise gape. How long this trick work? , does it has negative effect on caliper or brakes pads?

What are you doing! Replace those bolts man, seriously... tape?

Why you wearing gloves

Seems it's time for two new rubber boots as well. They have dried up and torn. The grease won't last there.

Wrong, wrong, wrong. Where is a rubber for bottom pin. Tape is nit heat resistant

Todas

Those dust boots are shot. Should have been replaced

That cello tape wont stand the heat.... Esp in hot climetes.

What the hell you are doing?

I can’t hear the sound from the mechanic because the damn music is so freaking loud why is it necessary to be playing music during this video?!

are you nuts ? this will fix the noise problem for 3 days only, you really think duct tape will hold the brake power? let me guess.. from india ?

This went sideways. I wouldn't waste your time with tape and grease. Pure hell

Well, that ratchet won't last long.

You e got to be joking right!? Is this seriously a video on how to fix your worn out brake calipers with clear tape! Lol what a joke man!

LOL

or buy new calipers..

Wait, did he write on the screen that someone did a hack job and in the same instance suggest that you put clear tape on your caliper pin..lol.... listen the rattle is coming from the second pin he just lubricated.. if you look their is a outline of were the rubber anti rattle sleeve goes..... it's fine to be a dummy but why tell other people how to be dummies also. Smh

Background music is terrible

My God....Just relace the caliper bracket and do it right. You shouldn't be working on cars if you're scotch taping brake parts

I can’t believe you are adding tape to the guide bolts. That is not going to fix the problem but for a day at most. If the parts are worn replace them. You could have a serious accident if your brakes fail & tape will cause it sooner or later. DO’NT DO THIS!

Erm. Wtaf.?....tape.🤔🤣🤦‍♂️

Totally wrong!