Thank you and no problem. I couldn't find alot of information back then when i started the built. The built is awesome, BUT: take your time, and do not cut corners. Then you will have very nice results.. also give the prop axle some extra attention. When to much power the axle will bend with the original coupling.. i have made a 3D printed bearing block design so the axle can't bend anymore on high torque.. And also installed a cardan coupling so the axle is fixed. Many succes with you built.

Thanks i lot, that's what i tought also!

Thanks, it all went well :D

Thanks! I use the seaking 120 amp ESC. And the seaking brushless 3660 motor. This is way overkill for this boat, but cooling is easy on this setup. Turned down the power now to 30% and still more then enough power..

Hallo, schön zu hören, dass Sie dieses Boot auch bauen werden. Das Boot sieht wirklich schön aus und segelt sehr gut. Ich selbst konnte damals bei der Orientierung nicht viele Bauinformationen finden, weshalb ich dieses Video für andere Bauherren gemacht habe. Ich werde unten Links zu den von Ihnen gewünschten Teilen einfügen. Vielen Dank für Ihren Besuch. Ich würde mich freuen, Ihr Boot zu sehen, wenn es fertig ist. Ich habe auch einen Surfer gemacht, der hinter dem Boot hängt. davon werde ich Werde demnächst ein weiteres Video auf KZfaq stellen. Links: Underwasser leds: nl.aliexpress.com/item/4000397704705.html?spm=a2g0o.order_list.order_list_main.26.5d5979d26BMIyW&gatewayAdapt=glo2nld Trimtabs: nl.aliexpress.com/item/1005004531269178.html?spm=a2g0o.order_list.order_list_main.5.5d5979d26BMIyW&gatewayAdapt=glo2nld Hoffentlich konnte ich Ihnen dabei ausreichend helfen Greetings FCRC

Vielen lieben Dank. Ich werde berichten. ❤

Gern gemacht.

Great build video am still sitting on the fence and about to build Najade, I went down same path as you for power Plant ,but went 180 amp esc hobby wing. The electric water pump was good idea as I’ve always just used a pick scoop under boats How did you bend the tabs that join the hull to the deck. Also what adhesive was used for the base plate that mounts motor and prop I was looking to use hot glue , I’ve got stability express for other plastic parts , I had thought about using carbon fibre to line the hull for more rigidity but I was reading instructions and it said not to use epoxy. You first boat build looks amazing finish look forward to more videos. 😊

The Najade is a truly beautiful boat, and great to build. I certainly wouldn't hesitate to start this build. The motor and ESC is way overkill and really not necessary. The drive shaft cannot handle this amount of speeds at all. The shaft has been warped 3 times by the power in the first sails. I have now made a double bearing block including cardan transmission to overcome the large axle ''hangover''. I also reduced the power on the ESC to +/- 30%. The pump is not necessary but I thought this was cool to add, and the waterjets in the back looks cool. You can warm the tabs a little with the hairdryer and bend them with your fingers. In terms of glue: I used Stabilit Express (brown), and Loctite 401 for the rest of the plastics. I certainly wouldn't use hot glue, it can deform the thin ABS due to heat. Also hot glue does not adhere well on the ABS, especially upon impact or vibrations. You don't actually need extra strength in the hull, this just creates extra ballast in the nose of the boat. Thanks for watching, and would love to see your boat when you have it ready.

Hello, no cutting! But i did use aluminium profiles to fix the trim tabs in position (flat with the hull) and glued the trim tab holders in position. Afterwards when the glue is cured then fix it with some bolts. I have some pictures when you are interested.

@@FCRC I would be happy if you send me some photos of the trim-tab installation. I'm having a problem. When I go at full throttle or near to full throttle, the boat turns left itself. I think using trim-tab will solve the problem but I'm not sure. (40-45 mm 2 blade propeller / 1000Kv Outrunner motor / 150A ESC) Maybe you can make a few suggestions when sending photos. Thank you

I was send message on Facebook for sharing photo. Thank you So much

@@atillasevli8993 more then willing to send you some pictures, send me your email adres please.. BUT! This left turn thing do have all the Najade boat with a powerfull setup.. the hull design is not for high speed and torque.. trim tabs don't solve this problem, they only produce a lot of drag when adjusting to much.. also i did have a problem of the prop axle bending with high RPM. Herefore i did design a bearing block to support the axle. This boat is awesome but it is not a speed boat unfortunately.

Send the message on this facebook page: facebook.com/share/TNWgriAD1PgTfwnA/

Natürlich habe ich viele Fotos. Welches würden Sie besonders gerne sehen? Schicken Sie mir einfach eine persönliche Nachricht über Facebook.

The full build took me around 2.5 weeks. Always in the evening hours, and a bit in the weekend days. Thank you for your interest.

Also where did you get this at?

I bought it at my local hobby shop, or you can order it at the Krick website.

Cool thank you, just ordered mine!

Nice! Would love to see the result. Succes with your build!