Here's how to rebuild the Carburetor : • How To Rebuild/Clean/T...
Пікірлер: 181
@dezee79443 жыл бұрын
I don't usually write comments but this was incredibly helpful, I don't know anything about nitro and I was able to completely disassemble the engine. The tutorial was very easy to follow and has aged well
@powerautosportsusa96912 жыл бұрын
This is the best nitro assembly video on youtube hands down.
@chrisvantuyl55543 жыл бұрын
Very informative video. The only thing I want to mention is at 5:13, it's worth noting that there is a small shim/washer that must not get lost that is on the end of the starter shaft.Also at 17:53, there wasn't that washer reinstalled, I don't know the importance of it,but wanted to point it out to others.And at 13:12, there is a oil hole on the bottom of the rod, it is on one side not in the middle, that side needs to face the carburetor to get lubrication.
@arturos.l.2248 Жыл бұрын
It helps as a barrier to keep oil or fuel from seeping across the shaft. And making the one way bearing slip. Without It, you run a higher risk of slip
@rogergreene22729 жыл бұрын
Just bought a TMaxx and having issues. Fantastic video to show how these things are put together. Perfect pace to hold my interest and perfectly thorough at the same time! Thank you!!! Subscribed
@midship_nc6 жыл бұрын
i was given a 2.5 tmaxx that had sat for about 8 years with no after run oil, crankshaft/intake valve was totally rusted and locked in the block....used some gun oil and channel locks to work the crank free....could not remove the sleeve so i could not fully disassemble...flushed it with oil and worked the crank around to the point it would freewheel nicely(about 40 minutes) and slapped it back together. Started and ran like a champ!
@EVERYDAYRC9 жыл бұрын
Very nice Jason. Very informative for people that aren't familiar with nitro engines. Nice work!
@willconter23349 жыл бұрын
Thanks for the video. I just got my 4 tec runing after 8 years of siting still and was able to get a better starter on it.
@officerskidmark9 жыл бұрын
Always nice to wake up and see a new video by DEH while getting ready for school
@abram32657 жыл бұрын
Thanks for the vid, great help in restoring a 2003 nitro rustler the engine hadn't ran in almost 13 years. Had dremel off a lot of rust and corrosion and replace the bearings but runs like new now 👌👌 keep it up
@fastrcs24899 жыл бұрын
Your videos are so informative, now I can learn new thing about my hobby without searching all over the internet !
@JasonTylerRicci5 жыл бұрын
Thank you. Your video helped my completely tear down my old Tamiya RC car engine for inspection and cleaning
@traxxashondakid9 жыл бұрын
Hey Jason, this is a great video on rebuilding a nitro. Also another good cleaner for these engines is automotive carb cleaner it breaks down the old oil and nitro really good.
@threemsrc69649 жыл бұрын
Awesome video Jason! Thanks for taking the time to film it.
@manolomonzon36464 жыл бұрын
Great video! You showed the orientation of the piston inside the sleeve! No one ever shows this!
@paulmcnamara169 жыл бұрын
Cool video buddy and i dont even own a nitro but i watched it to the end all the same. Be proud of yourself not many peeps interest me enough to keep me hooked on a subject id normally just skip by
@darkeclipticheart9 жыл бұрын
Thank you. That's great to hear!
@MrScothun7 жыл бұрын
Great video, helped me to get through my Vintage Kyosho GT engine strip
@brianjennings31727 жыл бұрын
Very well done. Thanks for the step by step, might have to do this soon.
@fc11336 жыл бұрын
Excellent work! Thanks for posting!!!
@dragonking79625 жыл бұрын
Thank you for this video. It helped me take my nitro rustler engine out! :)
@Flying904 жыл бұрын
Awesome video! I’m about to rebuild mine and this video was a huge help!
@jdubbfam374 жыл бұрын
Amazing. If it was one dude I know I could get the information I wanted and needed . It was you . Great video and I really do appreciate the help. I picked up a e Revo 3.3 nitro 1/8 scale she's beautiful and I hope this helps me get her started . I'm very egar to gut her out and making some noise.
@nifiyt8 жыл бұрын
man I watch all the videos you make. you helped me when I needed to rebuild my gearbox on my bandit vxl those videos really helped. this one is awesome to I am going to watch this when I need to take my 3.3 engine apart keep making more videos, your gifted so keep it up thanks again.
@MANWITHTHEPIZZA9 жыл бұрын
Awesome video. Love the way you explain everything in detail.
@corne01197 жыл бұрын
Joey true
@MANWITHTHEPIZZA7 жыл бұрын
Corne 011 damn bro a little late on the reply lol
@Deadbydawn719 жыл бұрын
Nice work- excellent vid!!
@drew_de89904 жыл бұрын
Thankyou so much!! This helped LOTS!!!
@johnathanwillis43825 жыл бұрын
Thanks a lot your video help me out in getting mine running again your video two thumbs up thanks again
@brianxr41607 жыл бұрын
Very good video! Thanks for posting.
@Tango_Mango_RT_3459 жыл бұрын
thank you Jason for making this video ! this will be very helpful in my near future lol
@jaysmith15495 жыл бұрын
Excellent video and clear voice
@Mrtojo9 жыл бұрын
Great video!
@sinplomosrc27924 жыл бұрын
Great Video! Helped me a lot with my old Hpi Rush! :D
@jackdurden4663 жыл бұрын
Damn you made that look so easy, I’ve never tried to rebuild/disassemble a nitro engine as I’ve never needed to. But I just bought a Jato with a 2.5 that could possibly use a rebuild and cleaning, and this info on disassembling them will prove invaluable. I only hope it’s in as good shape as that one is. If not, it’s getting upgraded to another, a 3.3 trade up from Traxxas would be just fine.
@larrykleist12957 жыл бұрын
Nice work. Thanks Bud.
@Rivazfar249 жыл бұрын
Thanks brotha, great video...I was looking into a t-maxx too much money
@FalconWing18133 ай бұрын
WD-40 is a must for these have! Nice video
@mintyoongi71618 жыл бұрын
awesome vid!! Very helpful
@Aaron-ro2yz Жыл бұрын
Thanks for making this video.
@kojot09769 жыл бұрын
Great vid. Love it!
@fatman242719 жыл бұрын
Hey man what job do u have to afford all those donations?
@nighthawkj30A42 жыл бұрын
Only complaints about the TRX 2.5 and 3.3 is the carburetors and bearings. Replace those with the O.S. 11K carb and Avid Race ceramics and the TRX is pretty competitive.
@F06M68 жыл бұрын
Thank you thank you! Engine would not richen and found out half of the piston was gone!
@countryboydollars95568 жыл бұрын
Same kind of thing happened to me when I burnt a piston from being to lean
@royarsey54296 жыл бұрын
very well tutorial...thanks man !
@jimw75279 жыл бұрын
Cool vid
@LawnboyFanatic4 жыл бұрын
This was great!
@arturos.l.2248 Жыл бұрын
Just a tip, don't bother taking the flywheel off if you're changing something in the backplate or replacing the piston sleeve and rod. Doing so is risky and a complete waste of time
@kentuckyrc21426 жыл бұрын
very informative nice video
@Eec20236 жыл бұрын
Great job
@nitro4life56 жыл бұрын
Very helpful
@Andylocktv9 жыл бұрын
Nice 👍👍👍
@sladka_ochen8 жыл бұрын
Не знал как достать пару, спасибо!
@PatRiot10410 ай бұрын
Great video! Will it run without the carb ‘boot’?
@RayBen5554 жыл бұрын
What kind of oil should I use for the bearings? I got to completely disassemble my Kyosho GXR-18 because of a crankcase crack. Hope I can save it :(
@bryden_smith3 жыл бұрын
Thanks for the vid was very helpful just completed my first engine tear down and rebuild and she goes good thanks for the help
@mikea89274 жыл бұрын
Nice video.. I'm barely getting into the rc world I had a few questions before watching this video honestly it answered pretty much A - Z.just was wondering on what or how would it be the best way to figure out the mount position on the engine honestly did not notice it was easier to remove the engine from the top screws than actually removing it from the bottom screws which now I'm having problems with. Witch I'm guessing I did not put them in the right postion since my tmaxx wont go one pressing the throttle. If anyone can give me a some good advice I would appreciate it.
@beamngcrashcompilationsd66902 жыл бұрын
9:00. Be very careful when turning the piston without the sleeve. I’m not blaming anyone, but when I did this the piston came up sideways and smashed about 1mm of the edge of the piston on the inside of the block. If anyone knows where to get a piston ONLY please link it! I need it for a 2.5. I need the piston but not the sleeve.
@nighthawkj30A43 жыл бұрын
That’s a Nice clean Traxxas TMaxx 😎
@RickRoseIsAwesome4 жыл бұрын
17:25 can you please give a tip on how to get the o-ring for the carb in the groove inside the engine? I'm pulling my hair out with how tricky this is.
@TungNguyen-vh6sl6 жыл бұрын
Thank you
@SOTOSKAWASAKI4 жыл бұрын
One of the best videos on how to disassemble a TRX engine. Is the process the same for TRX 3.3?
@itsyaboipatrick52184 жыл бұрын
Sotiris Karagiorgis yes
@smileywarrior18705 жыл бұрын
14:04 is it okay to use lithium white grease if I don’t have wd-40 or after run oil. Could I use PB blasterin instead of wd-40. Which would be the better option compared to lithium white grease or pb blaster. Thanks and thx for putting up such a great detailed video. I’ve had my traxxas t-maxx in the garage for about 4 years collecting dust. When I put it away I knew I had to replace the piston and sleeve. I’ve done this procedure like once 8 years ago so this video was mainly to refresh my memory. I do have we-40 but I’m just curious to know if I could use the above mentioned lubricants. Thanks.
@abdul-rahimahmed88337 жыл бұрын
THANKS A LOT
@pjks20064 жыл бұрын
Would be nice if you could explain what “pinch” is because this engine has absolutely no pinch from what I can see and it seems like it will be very hard to start
@spiderman0701044 жыл бұрын
I am wondering around the clutch shoes, does it have a spring around the clutch shoe, I didn’t see it in your model?
@mrcrowley120024 жыл бұрын
looks like you damage a tooth on the fly wheel with those channel locks..at 6:15
@nicholassalapoutis28294 жыл бұрын
he should have used a piston locker and a flywheel puller
@Osiris09259 жыл бұрын
Mean green works awesome for cleaning dirt and grime off. Soke the block with mean green. Then let it sit for a few minutes then you should be able to blow all the gunk off with ease.
@Sahadi4209 жыл бұрын
Simple green....blue bottle, and it says "motorsports" on it. Absolutely awesome. (and it's biodegradable)
@briannotafan33685 жыл бұрын
too bad he didnt rebuild it all that work + time for nothing
@briannotafan33685 жыл бұрын
try a real car like assoaitaded or mrc i took my rc 500 years ago and beat the shit out of these toys on a real track a mclaran body canam style car a old modified kb .45 helo eng traxis cars looked like they wernt moving
@briannotafan33685 жыл бұрын
futaba mag jr radio and look out i won week after week a good union job helps too
@vr4luva4915 жыл бұрын
I was rebuilding a Traxxas 3.3 motor but one of the crank case? Screws were stripped and that ended pretty quick the motor was about 8-10 years old
@street8487 Жыл бұрын
Great video.
@johnnield23893 ай бұрын
My traxxas 2.5 was seized up. I used liquid wrench and WD40 I finally all disassembled with the exception of the crankshaft. It spinning freely but it will not come out. It feels like it was pressed onto the bearings. I used a wood block and a rubber mallet and tried tapping on it. Would love to get it out to lube the bearings. Any suggestions???
@joshmatthiesen45522 жыл бұрын
Why did you not replace that broken cooling head?
@bradbozarth18223 жыл бұрын
What size is the O-ring that goes in the groove where the carburetor seats?
@benjaminolnhausen5234 жыл бұрын
Anyone else gasp when he dropped the crankshaft?
@Ole.red_4.6frmda2523 жыл бұрын
Sir I’m pretty sure that "bar" in the piston is a wrist pin but ion know I’m only 17😭😂
@lokomono894 жыл бұрын
Hey I installed the shaft and it was good. When I installed the sleeve the shaft/ crank was rough to rotate when piston was approaching top end. Do u know why? Thanks
@cameronchaos6663 жыл бұрын
When you take apart a motor and put it back together does it need to go through the break in process again????
@NehuennSant3 жыл бұрын
Only if you put in new parts, like a piston, rod, etc.
@Dyllon5919 жыл бұрын
When u put that new motor in u should make a video how to break in a nitro motor
@darkeclipticheart9 жыл бұрын
I plan on it. However it's still cold outside and one of the things I was reading up on is that you should break in a motor during fair, to warm weather. So I'm going to have to wait till a nice day.
@Dyllon5919 жыл бұрын
Ok Jason that would be a very help full video
@Dyllon5919 жыл бұрын
Because it can be very complicated to break one in
@briannotafan33685 жыл бұрын
try a tooth brush and brake clean or silverwere tray in dishwasher better yet ultra sonic cleaner
@robertsrbell78113 жыл бұрын
Couple things you did not mention there's a bubble on the rod that goes on the crank towards the crank side that should be on the same side as the cutout on the Piston which faces the carburetor of course and you should always check your mesha other than that very nice tutorial
@eoin4839 жыл бұрын
wow thanks i didnt realize nitro engines were 1 cylinder im an electric guy but im thinking about nitro
@mrfrost35 жыл бұрын
Eoin Shea they can be troublesome but great fun you should do it if you haven't
@gustavoavina31364 жыл бұрын
Hi! I have a question. Can you use a 3.3 engine crankshaft on a 2.5? Both are traxxas.
@alexmay9284 Жыл бұрын
Best video! Thanks a lot!
@rubenmartin77595 жыл бұрын
You do it superb! I don't talk English very well but I can understand everything you said. Hate people try to use crapy voices to sound cool, make it really hard to understand. I have a question. I have plan to run again a really old traxxas (comes with opel calibra dtm body) it was the cheap/small traxxas engine wen we buy. Can I install the automatic starter in this old traxxas engines? 🙈 🙈 I plan to upgrade electronics as well cause my old beauty drives on planes controller🤣, so I want giromode to a RWD that when finish is plan to run like a truck, is it to bad? 🙈
@LawdawgOD7 жыл бұрын
What did you use to clean it?
@tomaspuodziukynas53616 жыл бұрын
Do not use W40 as working lubricator. It is used to help to start moving stuff and cleaning. After short time it dries out leaving no lubrication. If you dont have anything better - few drops of any carengine /lawn mower is still better idea than W40.
@briannotafan33685 жыл бұрын
i used wd40 once to rebuild a 440 bombadear sled eng once be care ful i turned it over on my work bench i almost shit myself when it started up in my hand wd40 is flameable wow 2cil 40 hp running on a work bench not cool it ideled perfect
@sethperry13233 жыл бұрын
Very helpful!
@joeemanuel68134 жыл бұрын
Should always use flywheel puller instead of hammer
@Boldika19807 жыл бұрын
Hello, bearings to how be replaced? Thanx...
@CrivRex Жыл бұрын
Has anyone done the Traxxas Power-Up program where you return the engine and they give you another one? Wondering if anyone has been through the process. Otherwise, I’ll need to do this.
@devon84197 жыл бұрын
I'm starting a channel with the soul purpose of helping people with 1/16 Traxxas vehicles. Haven't made any videos yet, but I will soon
@funnyrc55919 жыл бұрын
You should get a summit
@kaynewman95797 жыл бұрын
does it matter if the heat Lopez cracked
@Ghost42o4154 жыл бұрын
One of my buddies gave me this without the engine and extras. Still has transmission. Is it WORTH the TIME AND EFFORT & MONEY to rebuild.???????
@rajveerbagri44924 жыл бұрын
Yes, dm me @the_traxxas_project on insta or maxx_rc on Facebook I'll help you
@420LegiTSwAg9 жыл бұрын
i noticed that when i turn the crankshaft the piston kinda sticks a little at one certain spot but goes smoothly the rest is this normal
@briannotafan33685 жыл бұрын
if it sticks in a spot scrap it somthings bent or out of round
@danielbaker11518 жыл бұрын
I'm having some trouble with my 3.3, when I tightened the back plate it gets really hard to turn over, do you know what the problem is? and if so how can I fix it?
@briannotafan33685 жыл бұрын
you fucked somthing up start over take your time
@MKhanfar-MWK6 жыл бұрын
What this traxxas chassis model ???
@THEMOWERMEDIC12 жыл бұрын
This can be morphed over to the 3.3 as well?
@Not_creativeexe6 жыл бұрын
I like to buy these nitro engines and take them apart for fun
@numerokix1849 Жыл бұрын
The sleeve on mine doesn’t seem to come out
@officerskidmark9 жыл бұрын
is your right hand okay? it looks funky on camera.
@darkeclipticheart9 жыл бұрын
Hands dried out from all the cold weather.
@officerskidmark9 жыл бұрын
darkeclipticheart ahh that sucks man. hey can you answer a question? at the beginning of your vids for the upgrades did you make the tunes or use already existing ones? starting to do RC stuff and was wondering.
@aaronchurchhill15087 жыл бұрын
He made them
@Ethan-nw5uk4 жыл бұрын
Wait isn't WD 40 a solvent?
@Ev0ltion7 жыл бұрын
My engine got some rust inside its more like just color cause i cant feel any damage to surface does this mean my engine goes to trash or can be still reassembled and used?
@darkeclipticheart7 жыл бұрын
Ev0ltion you can use some RC motor cleaner and it should be good.
@chuckd58777 жыл бұрын
If the engine works why would you throw it away? Running it for a while could help clear it out.
@briannotafan33685 жыл бұрын
try steel wool rust off first dont force it
@aceofspades27825 жыл бұрын
You never showed how to remove and to install the O-rings.