RC Tugboat 686 Customization　巷で流行っているトイラジタグボート686改造

No video

RC Tugboat 686 Customization　巷で流行っているトイラジタグボート686改造

Рет қаралды 7,198

Күн бұрын

The drive noise was resolved by replacing it with a rubber joint. In order to be able to move forward at very low speeds, I replaced the positive and negative wiring of the motor and reversed the forward and reverse directions. The high frequency sound generated by the amplifier at low speeds was reduced by wrapping the receiver box in a urethane sheet and pasting a 1mm rubber plate under the deck. I increased the rudder angle to be able to make small turns.
/ 1111875430160901

Пікірлер: 39

@Subwaterfilm 2 ай бұрын

Hi my friend,... what a wonderfull modification! The Tugboat 686 just swapped over to Europe and a lot of kids start their rc-career with it. Actually a lot of more older ones, like me, also did aquire one and are trying to modify them, too... thanks for uploading and describing what you did with yours.... Best wishes, Holger from Subwaterfilm

@KMorozou Ай бұрын

Hello, thank you for your comment! Sorry for the late reply. I take advantage of the low cost of buying it and don't replace the mechanism, just make some modifications and use it.

@Traveler_Greg 3 ай бұрын

Nice RC boat. Best regards and thanks for sharing. Have a good sunday. 👍

@KMorozou 3 ай бұрын

Thank you so much😉 Have a nice day！

@leirameirarc Ай бұрын

Very nice 👍

@KMorozou Ай бұрын

ありがとう！

@libmananchannel 6 ай бұрын

Hello "Morizou"! Thank you for showing us such a wonderful video! I feel so happy! I look forward to your next work! Have a nice day!

@KMorozou 6 ай бұрын

Hello, thank you for watching! A friend of mine also started remodeling. Have a nice day😊

@四国いいとこ撮り 6 ай бұрын

外観だけでもすごいのに見えない部分までハイレベルな裏技満載なんですね！凄すぎます😲

@KMorozou 6 ай бұрын

ありがとうございます！ついつい手が出てこんな感じになってしまいましたおもちゃなのでここまですることはないですよね😅4,000円以下で2.4Ｇプロポとサーボがついているのでコスパ最高ですお子様体験用にリリースします

@RcNickster709 6 ай бұрын

Fantastic!! Great looking boat my friend. As usual these things take some runs before they get nailed down. Great work and Thumbs up

@KMorozou 6 ай бұрын

Thank you so much😊

@JarcodeRover 6 ай бұрын

Silent but powerful :D Nice wake as well!

@KMorozou 6 ай бұрын

Thank you so much! The stock one was so noisy I thought it was an engine boat.😁

@freitaucher8225 6 ай бұрын

Love your Models

@KMorozou 6 ай бұрын

Thank you so much😉Have a nice day！

@SylvainsShipyard 6 ай бұрын

Nice work as usual!

@KMorozou 6 ай бұрын

Hello Sylvain, Thank you for watching. Have a nice day!

@thomasgargatte8916 4 сағат бұрын

Hello ! You made a great job on your Sea Bear !! I juste bought one. How did you reversed the forward and reverse directions on the command ? To still go straight when you push with your finger ? By the way all your job your boats is impressive 👏👏👏 greatings from France !

@denmasTe 6 ай бұрын

very cute 😍

@KMorozou 6 ай бұрын

Thank you so much😉Have a nice day！

@LANDSEAAIRCANADA 6 ай бұрын

SEA BEAR what a Great name Well done Friend

@KMorozou 6 ай бұрын

Thank you, dear friend!!

@doritiajsusername 5 ай бұрын

Hello. This looks just perfect. Very sleek and scale. Any chance of getting some build log, instructions or materials of what you did to the look of it? Thanks,great work.

@KMorozou 5 ай бұрын

@konantomo 6 ай бұрын

軽やかに航行していますね👍素晴らしい手作りのタフボートです。

@KMorozou 6 ай бұрын

ありがとうございます😊ノーマルはじゃじゃ馬です😅

@TV-pz2jl 5 ай бұрын

カッコ良い〜☺️ 楽しそうですね☺️

@KMorozou 5 ай бұрын

ご視聴ありがとうございました。マイナーな趣味の世界ですが、よろしかったらまた遊びに来て下さい。

@walter-YT 6 ай бұрын

とても素敵なモデル

@KMorozou 6 ай бұрын

いつも見てくれてありがとう！親愛なる友人😊

@walter-YT 6 ай бұрын

@@KMorozou あなたといつも...👍 親愛なる友人

@fredtedstedman 6 ай бұрын

what a lovely tug , you make such a neat job , she was well worth upgrading . is she 1:72 ?? congratulations honoured friend ! 😍😍🙏🙏🎥🎥

@KMorozou 6 ай бұрын

Thank you, dear friend! It looks like the number will increase at the club I belong to. The scale is about 1/48. It seems possible to make a 1/87 bridge using just the hull.😁

@bertdejong1923 2 ай бұрын

Great job!!! I have ordert 1 my self. Its gonna be working as a recovery tug for my othter rc boats. I have a question,where can 1 find the bumpers that's you have on youre tug? And on fb i see that you have made a kind off "buldozer" on the front. Love it!!! That you also can house as cleanup system. Can i find it somewhere? Keep up the great work.

@KMorozou 2 ай бұрын

Thank you for watching! The bumper was made by processing plastic sheet. Urethane sponge is used as a cushioning material. The attachment for recovering the boat was made by processing the grill of an old electric stove. For attachment, we used Insiloc, which is used to bundle electric wires. Details will be posted on Facebook, so please check it out.

@bertdejong1923 2 ай бұрын

@@KMorozou Thank you!! 👍👍👍

@ShaggysDiving 5 ай бұрын

Did you also change electronics on the 686

@KMorozou 5 ай бұрын

The transmitter/receiver and motor are used as is. I replaced the positive and negative terminals on the motor to improve the rocket start. I reversed the throttle lever's forward and backward movement.