RCBS Auto Bench Priming Tool - Improvement- makes a good product better!
Пікірлер: 33
@deantiffany18563 жыл бұрын
Thank you, it so happens I only have one arm. This helps immensely!
@gronthomson3 жыл бұрын
GREAT IDEA! I just ordered one and will definitely do this! Thank YOU, JoJo Trader!
@johnblood37313 жыл бұрын
Great idea. The only thing I would do different is turn the shell holder opening to the other side so brass could come in from the right. Take care.
@glenj.taylor29384 жыл бұрын
I just picked one of these up, thank you very much for producing and sharing such a great idea.
@ElmoColt453 жыл бұрын
I just purchased one of these primers from RCBS, this is the best primer tool ever, buy one, you're going to like it! Trust Me
@michaelmallory94906 жыл бұрын
That's perfect and super simple too. Thanks for passing on your trick
@fxrs19825 жыл бұрын
Awesome improvement!!! I did it and it works out great!!!!! Thank you so much!!!
@Gunners_Mate_Guns2 жыл бұрын
Just as with most ideas that work best, this is simple and elegant.
@MAGA2024.5 ай бұрын
Damn i love this tool
@markvaz56245 жыл бұрын
Reloaders are an ingenious lot. I use the same tool and agree, the handle flopping is a bit annoying.
@dsquires163 жыл бұрын
Great idea. Thank you
@kimhansen63845 жыл бұрын
Nice tip. You need to clamp the base to the table.
@WALLOWINGBULLS3 жыл бұрын
Thanks for passing that on , good idea
@duanelarson6005 Жыл бұрын
Nice ! Awesome idea I like it !
@1stFlyingeagle Жыл бұрын
I love simple solutions. Well done.
@10hunterLab2 жыл бұрын
So simple. So effective. Well done. (why didn't rcbs think of this?)
@johnfrederikson20026 жыл бұрын
looks great; thanks. J.
@scarter1762 жыл бұрын
Compression spring under handle ?
@Stevesmith-yw7cr2 жыл бұрын
I know this is an older video but I have found something that works really well...better than duct tape. Take the hooked self adhesive backed VELCRO and cut a small piece to stick it into the same area that is indicated in this video. It acts as a shock absorber stopping the tube bounce and makes no noise at all. I did that a few years ago and it still is doing a great job. Just my 2 cents. Oh yeah....... TRUMP 1
@usasfga126 жыл бұрын
Interested in the white plastic platform you use on the shell holder. Is there performance effect with that. Is this another improvement you made
@usasfga125 жыл бұрын
J.What did you do to make the plastic platform fit to the correct feed position
@03patines Жыл бұрын
Mine came with a spring 'wrapped' around the pivot bolt , and it keeps the handle in the home position, as your rubber band does.
@XxxxInsan3xxxX2 жыл бұрын
not bad buddy!
@amerlalic12672 жыл бұрын
I made spring behind handle around handle mounting bolt housing. Keeps handle in upper position.
@patrickkearney87746 ай бұрын
Could also just put a spring under it
@robertpowell27466 жыл бұрын
Jo Jo I mounted a coil spring on mine between handle and base. I will send you a photo if I have hour e-mail.
@adrian14286 жыл бұрын
robert , can you also send me a picture
@robertpowell27466 жыл бұрын
bun ny send me your email I don't know how to add a photo to you on you tube.