REAL WORLD PLUMBING PROBLEMS | BUSY FEW DAYS JOBBING ABOUT….

Рет қаралды 17,126

Жыл бұрын

Real world plumbing is my little saying on this channel, and a few days jobbing about sjows this to be the case, from angle grinding toilets to get them apart to working in a house full of lots of other trades...... the plumbing game is always busy
#plumbing #howto #diy
Massive Thankyou to my channel sponsor UNILITE….
To save 25% on all Unilite orders type “MJTIFF” at checkout
unilite.co.uk/
Also check out the Trade Legends KZfaq channel-
/ tradelegends
And head to the Trade Legends site for some massive discounts
tradelegends.uk/

Пікірлер: 127

@MJTiffPlumbing Жыл бұрын

Back to a few days jobbing about….. always something to get onto…👌🏼

@barrybryant1982 Жыл бұрын

Hello from kos mate im a English fan watching abraude

@jaehus1971 Жыл бұрын

I wish all plumbers were like you!

@MJTiffPlumbing Жыл бұрын

Thanks buddy…… kind words

@solventdonkey Жыл бұрын

To drain the towel rad, take the air vent out, pop a length of 15mm copper in with a hose connected and syphon out all the water. If you haven't got the hight you can use a bit of 15mm plastic

@MJTiffPlumbing Жыл бұрын

👍🏼👍🏼

@russellbaldry5095 11 ай бұрын

Regarding the rad 100% agree those brackets are a pain. I hung the vertical type recently on a dot and dab wall and it took ages to get them levelled up! It wouldn’t be so bad if the manufacturer had a table in instructions with some measurements on🤷🏼‍♂️

@MJTiffPlumbing 11 ай бұрын

👍🏼👍🏼

@russellbaldry5095 11 ай бұрын

The amount of times ive took off those cisterns and the customer is horrified and embarrassed that there is black mould underneath!😆have to say though i wear my turtles (gloves) on every job🙈😂

@MJTiffPlumbing 11 ай бұрын

🤣👍🏼👍🏼

@dirtydog2312 Жыл бұрын

I bought a cordless Dremel, it’s nice and compact and easy to get in on cistern bolts. Have also used it inside a soil pipe to cut it down when I couldn’t get anything else in there

@SteveHit1 Жыл бұрын

Another very interesting video, great work too! Thanks for making it. Rusty toilet bolts are always a pain - easier now with a multi tool but I remember having had to use a hacksaw blade, with masking tape wrapped around for a handle, in the past!

@MJTiffPlumbing Жыл бұрын

Yep done that I few times over the years

@solventdonkey Жыл бұрын

I do like a bit of silicone when putting a close couple kit in and that syphon could do with a shorter C hook. I'm glad I don't do domestic plumbing but then again I come against the Twyford nocturn kit. 😂

@MJTiffPlumbing Жыл бұрын

👍🏼👍🏼

@MEGACHANCE360 Жыл бұрын

Soldering is the best option still! And I think a neater job great video though mark👍🏻

@MJTiffPlumbing Жыл бұрын

👍🏼👍🏼

@manjsingh6500 Жыл бұрын

A star so knowledgeable ⭐️

@MJTiffPlumbing Жыл бұрын

Thanks buddy

@LemonGamingHD Жыл бұрын

Need to be marking insertion depth and bunny ears on press fittings. If you ever have a bad leak and flood a house. The press-fit manufacturer would pay out if it’s there product that failed but not if you haven’t been marking fittings..

@MJTiffPlumbing Жыл бұрын

👍🏼👍🏼

@acdheatingandplumbingservi7635 Жыл бұрын

Mark you should buy some plumb tubs way easier than the folding buckets for them little jobs tight down on rads etc

@MJTiffPlumbing Жыл бұрын

Yer need to get some to be honest👍🏼👍🏼

@keithcampbell7214 Жыл бұрын

Great video Mark, I learn so much watching these jobbing videos as a DIY’er, keep the good work up 👍

@MJTiffPlumbing Жыл бұрын

Thanks buddy 👍🏼👍🏼

@tigercoatings7092 Жыл бұрын

Top job Safety glasses 👀🥸🥸 with that grinder

@MJTiffPlumbing Жыл бұрын

🤦🏻‍♂️

@paultabor2446 Жыл бұрын

Love the channel i dont have a wet vac like yourself but have another make how handy they are. I had to drain a washing machine recently . The darin is so low water goes onto floor use wet vac problem resolved

@MJTiffPlumbing Жыл бұрын

Thanks buddy….. wet vacs are a great addition to the tool kit

@chrisholt2474 Жыл бұрын

Hi Mark, another nice film there thank you, I still enjoy seeing all the jobbing about stuff. Some nice jobs there successfully completed, hope all is well with you. As always take care, regards, Chris. 👍👍👍

@MJTiffPlumbing Жыл бұрын

Yer thought you would like this one Chris😉

@lee2003uk Жыл бұрын

Mark do some more videos on pricing small jobs

@MJTiffPlumbing Жыл бұрын

Yer I should do I think

@tirvplumbing Жыл бұрын

Great work as always Mark 👌💪 only thing I'll say as a welders son is wear your eye protection with the grinder. The amount of times my dad ended up getting slag picked out of his eyes that had gone at an angle and even got past the glasses was unreal. Always pays to take a second to look after yourself. 👍

@riptiz Жыл бұрын

Being a pipe fitter by trade I hear you. I’ve even had shit in my eye go past a visor and safety glasses.

@MJTiffPlumbing Жыл бұрын

Yep I hear you guys 🙌🏼🙌🏼

@tonymurff5234 Жыл бұрын

All the big guns came out for that cistern repair God be with the days when we had to lug around 110 transformers and leads, We have it handy with battery tools now 🙏 Your getting used to the press fit Mark, Good Video as always 👍👍🤜

@MJTiffPlumbing Жыл бұрын

I was on about 110v stuff to someone last week!!!…. Good old days

@gracebateman777 4 ай бұрын

Jobbing about ❤

@MJTiffPlumbing 4 ай бұрын

Yep

@johnboy2984 Жыл бұрын

Hi Mark. Good few jobs done. I am fitting them rads in my house so thanks for the tip with the bracket’s mate. Have a good weekend 👍

@MJTiffPlumbing Жыл бұрын

No worries buddy

@mattundercoat Жыл бұрын

Thanks for that, Mark. Something for everyone with a jobbing vid, and no major unexpected ballache. At least those cistern bolts gave you fair warning they were going to be trouble!

@MJTiffPlumbing Жыл бұрын

Yep…. Seem to be getting all the crappy toilet jobs latterly

@mattundercoat Жыл бұрын

@@MJTiffPlumbing I see what you did there… 😄

@rush211251 Жыл бұрын

I sometimes get the brackets mixed up on those column rads , and put the bottom brackets at the top 😮. One tip I use when hanging these radiators , is place my tool boxes under the rad at the specified height , then offer the bracket in place and then pencil mark it .

@MJTiffPlumbing Жыл бұрын

Yep…. I’ve done that more than once 🤣🤦🏻‍♂️

@andyroberts9562 Жыл бұрын

Thanks for taking the time to do your videos always enjoyable content 👍

@MJTiffPlumbing Жыл бұрын

Thankyou Andy….. very kind words

@daveperkin8376 Жыл бұрын

Great content, really enjoy the jobbing videos, picking up tips along the way. Cheers

@MJTiffPlumbing Жыл бұрын

Thanks buddy 👍🏼👍🏼

@antoniogalluccio4213 11 ай бұрын

I'm doing the same with radiator top brackets nice and level in first and bottom ones later on. If I put all four on the wall even level and plumb wit the top ones the rad is not gonna sit right.

@MJTiffPlumbing 11 ай бұрын

👍🏼👍🏼

@DarrenFord55 Жыл бұрын

Once again real world mate, what's great about you is you don't big yourself up like some on you tube boasting about how they are pilots or whatever. Glad i switched to your channel keep it up Mark.

@milkyporridge5929 Жыл бұрын

Can’t stand that fool as well

@MJTiffPlumbing Жыл бұрын

Thanks buddy…. I am what I am…. Just keeping it real

@leebesnard8054 Жыл бұрын

Hi Tiff. I tell you what I've started using to get the rusted cistern bolts out is a Milwaukee Hackzall with a metal cutting blade. It fits between the pan and cistern and cuts through the bolts very quick. Good video as always 👍

@MJTiffPlumbing Жыл бұрын

Good shout that…. Nice little tools

@leebesnard8054 Жыл бұрын

Got the M12 nice and light. I seem to be using it more and more. A lot quicker then the multi tool on the bolts👍

@56ty78ui Жыл бұрын

The rust under that cistern and on the nearby rad. Somebody can't control where their piss is going. 😄

@MJTiffPlumbing Жыл бұрын

Hahahahaha so true

@ciaranboughton4713 Жыл бұрын

Real world stuff mate 👊

@MJTiffPlumbing Жыл бұрын

Thanks mate 👌🏼

@honolulu1476 10 ай бұрын

Thanks

@MJTiffPlumbing 10 ай бұрын

👍🏼👍🏼

@donaldduncan6017 Жыл бұрын

Doing what you do best. I prefer the toilet handle pointing slightly upwards less downward force needed to flush toilet.🤙🏿

@MJTiffPlumbing Жыл бұрын

It’s all about the pivot point 🤣😉

@andyfadian Жыл бұрын

Good luck Mark on smashing 30K subs, great content as always 👍

@MJTiffPlumbing Жыл бұрын

Thanks Andy 👍🏼👍🏼

@tony78652 Жыл бұрын

Hey Tiff , I thought this was a 20sec change, well thats how long it took you last time!....lol...great videos, great channel.

@MJTiffPlumbing Жыл бұрын

🤣🤣🤣……. Only when it’s a Turbo88 to an Edge😉

@scousersontour7601 Жыл бұрын

i would love to see the algorithm vid, i cant get my head around it!

@MJTiffPlumbing Жыл бұрын

Oh mate it’s soooo complicated…. But really good when you learn it

@glyndavies591 Жыл бұрын

Nice looking rads but as you said the brackets can be a pain to line up glad to see you changed the flexi under the toilet

@MJTiffPlumbing Жыл бұрын

Coloum rads are a right pain….. just have to take your time

@kevinisaac9139 Жыл бұрын

I agree done loads of taps and cisterns had one yesterday multi saw job what would Ido without it used to have to use a junior hacksaw

@MJTiffPlumbing Жыл бұрын

Can be a right pain

@Wattsjoinerybarn Жыл бұрын

Great videos. I only have the tolerance to follow one plumber so congratulations 😂 ps I need that algorithm video

@MJTiffPlumbing Жыл бұрын

Hahaha thanks buddy…… Appriciate the follow👌🏼

@davehunter6920 Жыл бұрын

the old skill of soldering will soon be a thing of the past...unless 10 years they discover pressfit to be a disaster with leaks everywhere lol

@MJTiffPlumbing Жыл бұрын

Good job I am still soldering…..👌🏼👌🏼…… But you’ve got to give these new things a chance. Over 20years pressfit has been about now

@codyhowes2079 11 ай бұрын

It already is a thing of the past here in Germany, you learn to solder and braze as apart of your apprenticeship but it’s pretty much all press fittings now…

@riptiz Жыл бұрын

I believe once you start pressing you aren’t meant to stop and start as you might overpress it.

@MJTiffPlumbing Жыл бұрын

If it’s calibrated correctly it’s not a problem👍🏼👍🏼

@YNWA-oq5uf Жыл бұрын

You've probably got a valid point but how can you stop it once it's started?

@dannyhogi4953 Жыл бұрын

Other great video mate

@MJTiffPlumbing Жыл бұрын

Thanks buddy 👍🏼👍🏼

@brendanfisher2528 Жыл бұрын

I use alot of 45 and street 45. Dunno if it's out of laziness or can just look more semetrical if everything is at the same angle, plumb and level.

@MJTiffPlumbing Жыл бұрын

Yep they seem to be a thing in pressfit

@garyredfern5303 Жыл бұрын

Them shower screens are a pain. I did 2 the other day and withball the other trades flying about on site is a nightmare. Wish you could build them in the garden 😂😂👍👍

@MJTiffPlumbing Жыл бұрын

Just so fiddly getting the top and bottom bits onto the glass

@garyredfern5303 Жыл бұрын

@@MJTiffPlumbing and there is always the worry that you give it that little bit to much and it breaks

@harrislondon Жыл бұрын

I hope that customer isnt tall with that toilet being located there 😅

@MJTiffPlumbing Жыл бұрын

No they are not

@michaelbolt4530 Жыл бұрын

Im due to go to a job where im fixing a flush syphon flap thingy, I might get one of those dudley turbo jobbies

@MJTiffPlumbing Жыл бұрын

You won’t go wrong if you do😉👌🏼👌🏼

@kevinisaac9139 Жыл бұрын

I use a plumb tub

@MJTiffPlumbing Жыл бұрын

👍🏼👌🏼

@michaelbolt4530 Жыл бұрын

Who makes that toilet syphon you were using at the show?

@MJTiffPlumbing Жыл бұрын

Tyde or as some know it Thomas Dudley....... the only syphons i fit

@SuperWayneyb Жыл бұрын

🤘😎🤘

@MJTiffPlumbing Жыл бұрын

🙌🏼🙌🏼

@Get0ffMyBike Жыл бұрын

PB has a Nerad flexible funnel on his video from today 🤔😂😂

@MJTiffPlumbing Жыл бұрын

He’s bloody had it ain’t he🤣🤣🤣…….. I will ring him tomorrow and get it back🤣

@Get0ffMyBike Жыл бұрын

@@MJTiffPlumbing I’m sure he will give it back if you can win an arm wrestle! 🤣

@may2may277 Жыл бұрын

Whats the difference leaving filling loop open sticking hose on a drain off manual flush system vs through flush? I honestly think through flush unit is gimmick manual flush does the same thing ?? When will you make video on installing water softner ?

@MJTiffPlumbing Жыл бұрын

Can you switch direction to just the main….. nope

@may2may277 Жыл бұрын

@MJTiffPlumbing can you please explain your answer ? Filling loops on mains water is going into the circuit?

@user-nf9wi2gj8w Жыл бұрын

i like your t-shirt where is it from please Mark?

@MJTiffPlumbing Жыл бұрын

Which shirt is it??

@user-nf9wi2gj8w Жыл бұрын

@@MJTiffPlumbing knipex mate

@MJTiffPlumbing Жыл бұрын

Knipex 🤣😉👍🏼👍🏼

@vikashmohanchauhanyoutubec2891 Жыл бұрын

Like👍😂🎉😊

@MJTiffPlumbing Жыл бұрын

🙌🏼🙌🏼

@luckyluke8052 11 ай бұрын

What brand is this vacuum?

@MJTiffPlumbing 11 ай бұрын

Milwaukee 👍🏼👍🏼

@David-mb3eq Жыл бұрын

Thats real world plumbing we don't need PPE lol

@MJTiffPlumbing Жыл бұрын

🤣🤦🏻‍♂️🤦🏻‍♂️….. I knew someone would pick up on that… my bad

@diyjohn9584 Жыл бұрын

What watt was Walt walking with?

@MJTiffPlumbing Жыл бұрын

@steviegvxr Жыл бұрын

God I wish you wear gloves when touching toilet stuff. Other than that bravo sir.

@MJTiffPlumbing Жыл бұрын

That’s what big wipes are for

@accesszero4803 Жыл бұрын

I think u using press in the wrong way , i preas all the time., but dont use it like thag under the floor

@MJTiffPlumbing Жыл бұрын

Sorry…. Can’t make any sense of what you’ve put??

@aldarbz Жыл бұрын

Love the videos , but the lack of eye protection makes me cringe , be safe, be successful...

@MJTiffPlumbing Жыл бұрын

Thanks mate… yep I hear you

@user-uq4xv3vd5e Жыл бұрын

Done .it.with.double.side.hacksaw.blade