Rear Brake Disc Renewal - Peugeot 307 & Peugeot 308

Рет қаралды 67,009

Күн бұрын

How to remove and replace the rear brake discs in a 2001 to 2008 Peugeot 307 and a 2007 to 2012 Peugeot 308. These are the brake discs that have the rear wheel bearings built into them. Thanks for watching, please comment, like and subscribe !.
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2020
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.

Пікірлер: 38

@tomndines 7 ай бұрын

I did this today on my '09 308. Was a bit of a mission! I also needed a 36mm socket for the hub nut. All of the bolts were a lot tighter than they are in this video...! The caliper bolts especially so - needed a well-fitting and good quality socket to not round them off. The T50 bolts were okay, as they are much less prone to rounding out. Oh, and the piston rewind was an absolute sod, becuase the brakes being so worn meant the tool wouldn't fit at first!! Thanks for the guide - it was V useful.

@bitacora1354 26 күн бұрын

Por eso el estado del metal no sabía sierra en el campo con mucha humedad hasta que cantaron las gaviotas 😅😅😅😅 la costa

@jeffburkett180 3 жыл бұрын

If possibity of reusing hubnut always good idea to make an opposite notch with angle grindet for staking in fresh position.

@nickbos17 5 ай бұрын

Thank you for the video!

@screwsnutsandbolts 5 ай бұрын

You're welcome !

@MartynStubbsTBS 2 жыл бұрын

Looks so easy , great job thanks, Peugeot garage £500 , I could save loads

@screwsnutsandbolts 2 жыл бұрын

No problem 👍

@burhanburhan1988 Жыл бұрын

Very good video thank you !

@screwsnutsandbolts Жыл бұрын

You're welcome, thanks for watching !

@Passengervehicles 3 жыл бұрын

Good video, thanks

@screwsnutsandbolts 3 жыл бұрын

You're welcome :)

@uploadsnstuff8902 Жыл бұрын

On a 308 (T7) the hub nut requires a 36mm socket. And needs to be tightened at 300N.m.

@JellySIde-qj4uv 10 ай бұрын

Wish I would of read this before I bought a 32mm socket and took the wheel off. Doh!

@michaelgarner9816 2 ай бұрын

@@JellySIde-qj4uv I knew there was a reason that I buy them in sets and not singles😂😂

@michaelgarner9816 2 ай бұрын

Time to break out the big torque wrench 😂

@guvenunal4894 2 жыл бұрын

For people who watch this video and want change brakes. Dont forget the ABS Ring. İn the new disc there is often the abs ring not included.

@mayhemmechanics4068 10 ай бұрын

No abs on 2009

@costym.2328 3 жыл бұрын

Felicitări pentru aceasta prezentare este o lecție bună. Succes

@screwsnutsandbolts 3 жыл бұрын

Thank you ! :)

@terryjones2012 Жыл бұрын

once car has been lowered, and is what's known as kerb weight, always torque the wheel studs to spec

@davidreeves5879 Жыл бұрын

Good video thanks

@screwsnutsandbolts Жыл бұрын

Thank you !

@CarlosHenriqueNoronhadeAguiar 3 жыл бұрын

This serves to C3 1.6 too!

@toxmaster1 3 жыл бұрын

Good job but when you disassemble all that stuf you should have show how to clean abs sensor (common problem on 307) , lubricate caliper guide pins,...etc

@screwsnutsandbolts 3 жыл бұрын

Thanks, this was just a basic demonstration on how to replace the discs. I might do another video on the abs sensor at some stage.

@Kimians 2 жыл бұрын

What about the hydraulic plunger? You won’t get new pads in if the old ones are worn right down and the calliper plunger needs adjusting to fully open.

@michaelgarner9816 2 ай бұрын

In that case you need to remove the cap from the brake reservoir and use a wind-back tool or piston compression tool. Don’t forget to replace the reservoir cap, start the engine and pump the brakes repeatedly until they firm up once you’ve finished.

@csraln6748 2 жыл бұрын

How often do you have to change the break pads and rotors? Any signs that they are worn enough for a change? It is ok to only change the front or rear brakes? Not all at the same time

@screwsnutsandbolts 2 жыл бұрын

It depends on how hard you brake and how much mileage you put on the car. You usually change the pads every 10 to 20 thousand miles or when any one of the friction surfaces reach the minimum thickness and the rotors every 60 to 70 thousand miles or when they reach the minimum thickness, and yes it's ok to change just the front or rear brakes but never just one side of either.

@ellocofusca Жыл бұрын

All the 307 are the same? I mean, all 307 have this kind of “assembly” of brake disk and hub or there’s another model with independent brake disk? Thank you so much. Greetings from Uruguay.

@screwsnutsandbolts Жыл бұрын

No they're not all the same. Some 307s might have disks independent from the rear bearing

@jacobljung7840 Жыл бұрын

Great video. Just one thing to note if you were to do it yourself: I’m guessing this is the SW? I have the Hatchback (308 -09) and the hub nut is 36mm instead of 32mm like this one. Thanks for a straight forward guide👍

@screwsnutsandbolts Жыл бұрын

Thank you !