I rebuild this carburetor from Keihin for my Honda 400 t to put it in stock. So i have one if needed. I used a ultrasonic cleaner from ebay. Cheap but it works well.
Пікірлер: 36
@enoughenough20074 жыл бұрын
I’ve watched this all the way through. I have a better idea of how to disassemble and reassembled my carbs. Thanks. But now I’m also hearing that background song in my sleep. Lol
@HiHoWillyO4 жыл бұрын
That throttle return spring for the second carb is killing me! Gahh Great video tho! I really appreciate the full depth here!
@matildehunter85934 жыл бұрын
If you ever have to rebuild this again can you please show what you are pulling out of where? This is the only video that's even a little helpful but there is a lot I can't see. When you disassembled the bowl were there any O-rings around any of the jets? Or crush washers?
@emilianoalvarez82433 жыл бұрын
Excelente trabajo!! Estoy por hacer lo mismo en mi cb400t 81. Muchas gracias!
@aidanpinkston69703 жыл бұрын
I’ve got a 78 cb400 with vb carbs on it. Looks exactly like the one in the video, but mine had caps on the middle hole in the float bowl. Are these caps needed?
@paulorodrigues8774 жыл бұрын
All those seals should be changed. Especially the one in the axel of the butterfly valve that control the throttle. Other wise the air will be sucked through there and the vacuum won't be made in the jets logically gasoline won't be sucked and than motorcycle will not run. That is why some motorcycles only run on choke. That is the only way to reduce air flow and increase vacuum to get gasoline in the piston. 😃
@Cartoon_Physics2 жыл бұрын
Groovy music, but I could use some explanation of what you're doing.
@milantocinovski86143 жыл бұрын
What about felt o-rings on the shaft, or this model doesn't have them!?
@treetment15 жыл бұрын
Hello, What type of product do you use in your ultrasonic pool? Thank you for your video
@giuseppelamanna1095 жыл бұрын
Only water and Dishwashing liquid. Think there are better Produkts.
@benjaminsalopek33944 жыл бұрын
What would you charge to do mine?? Same ones, 78 cb400t I would forget how to put it back togther! Lol
@chanmoua4 жыл бұрын
Can you do a tutorial on this exact carb cause I cleaned mine and now my bike won't idle without getting choked and there's a lot more vibration when choked. Also won't pass 4k rpms when revving
@jackvacuum6193 жыл бұрын
Adjust your idle mixture screws
@CaitlinDemers5 жыл бұрын
What kind of polish did you use with the dremel to make it shinier?
@giuseppelamanna1095 жыл бұрын
aluminium polish
@markhayvren22032 ай бұрын
Where are u located ….need a rebuild on a CB400T 1978?
@dvvalant2 жыл бұрын
I would have many parts left over!
@MrUberHaxor4 жыл бұрын
notice you didn't touch the float seat at all is there a way to remove them, Pressed in or screwed in?
@Wmoore14 жыл бұрын
It's just a pin. If you're rebuilding it, use one of your old needles to push the pin through. It might need some solid taps to get it out.
@lamebotasproduction82304 ай бұрын
Thanks for the video
@juanvaldeazy16634 жыл бұрын
I took apart my carb and the one of the floats has fluid in it. Its sealed too so I cang get it out. Is that normal?
@Wmoore14 жыл бұрын
You shouldn't have gas in your floats.
@wthorpe4202 жыл бұрын
Where did you get those floats
@Reedspeedman1234 жыл бұрын
song?
@hristoanastasov94953 жыл бұрын
I'm sorry guys but I'm not see on the tube O-rings on side by side of carburetors...
@michaelsandoval50004 жыл бұрын
hola buen video mi moto tiene un carburador totalmente igual a ese que muestra en el vídeo.es moto CM400HONDA ańo 81 pues mi pregunta es será posible encontrar algunos repuestos de el motor mi moto gasta aceite y se escucha que suena como baleros guangos kiciera ir aún taller pero nesecito saber si encontraré repuestos.. grasias soy de el Salvador.
@arielalvarez70193 жыл бұрын
minute 28:22 didn't fit the idle diffuser caps. minute 29:43 didn't fit the small air valve seals I don't think that carburetor works properly
@zieniet3 жыл бұрын
The CM came with 2 different carburetors. In the Us it's slightly different.
@adyastley61974 жыл бұрын
In the 28:22 time of the video I see that you did not put the rubber plug in the middle hole prior to putting the top on. I am wondering if I need this because one is fine and the other went a little mushy and damaged pulling it out. I guess I will leave it out too on one. Great job BTW
@johnpaulnassutti7493 жыл бұрын
Min 37 can't understand where the spring goes!
@joequesada22394 жыл бұрын
where did you get the rebuild kit
@giuseppelamanna1094 жыл бұрын
Don't use one at this time. Only clean it for stock.
@alokbhangre23663 жыл бұрын
I own a 1989 honda Accord with Kehin Dual carbs. I desperately need your help to restore it. Can you please provide an email or number ?