"My wife would've freaked if she knew what I was putting in there but she never asked so I never said nothing" 🤣🤣🤣 right on

I've been told never to sink the injectors in a water solution if you are gonnas ultrasonically clean them, I was told to use a mix of gasoline and thinner, ideally I'd have power to them to keep them open and a hose connected sucking the cleaning fluid backwards through them as the ultrasonic cleaner did it's work.

If the readings are off most of the time it's the multimeter which isn't well calibrated. I had the same issue with "electric guitar pickups" and reading out of specs values all the time, until I trashed the multimeter and finally bought a professional one ... not even that darn expensive at all, and a lot more range in most options ... great for everything from house to electronics etc, and car repair.

Literly just googled Bosch injector rebuild after order the kit to do my g60 .... thank you

The background makes me feel like I'm watching an automotive AVE video

Thanks for the vid. screw to pull out filter is genius.

To remove the internal filter/screens I used a shorter screw. I tried a couple lengths to determine the length needed so the underside of the screw head contacts the top metal sleeve or cylinder of the injector then it acts like a hub puller and pulls the screw out by simply turning a screw driver. In my case, the screw only went maybe 1/8" into the screen until the back of the screw head contacted the top of the metal cylinder and then pulled the screen out without a vise or much effort. Try it.

Thank you for the education 🙂Highly appreciated.

Dishwashers are amazing machines also, especially if you have the house to yourself a while.

One question bud, I did mine as per your video, but I did notice the original filter is a good bit longer than the replacement filter, so much so that when the original filter is tapped into place the plastic bottom of it rests on 4 tiny feet on top of the bed were it seats into. The new filter once tapped into place does not rest on the bottom of its seated position and leaves a gap. I'm asking as I'm wondering will the 100psi in the fuel rail not pop of the bottom of the new filters now as there a little shorter and have that gap at the bottom where as the new ones were supported as they sat flat on the bottom?

5:24 She don't ask, I don't tell LOL!

Awesome cleaning on the spark plug but as always good video ;-)

Great video! Was entertaining to watch

thanks for video, I'm about doing the same on my MX 5 Miata and way more confident after seeing you making the job...looks pretty straight forward. Greetings from Belgium

nice video. just wanted to ask, what did you use in the ultrasonic cleaner? I saw some soap bubbles - just a little dish soap? or something else?

Hey I just had a thought... maybe they can be pressed out by putting a metal cylinder around the screw (the same diameter as the filter) so as you screw in the screw it presses out... hmmmm...

2 Comments, 1) Hot readings will be a bit higher as resistance goes up with Heat. 2) I would consider a better quality DMM. I use one of these to lend to a pesky salesman in my dealership. For $3 keeps him from abusing my Real Meter. The Low OHM reading are inconsistent with that meter but for 3 bucks I suppose one could argue its a Great Value.

Hi there Petal to the Metal, my injectors look just like what you have in this video. 8 have 8 of them though, so am I believing that if I follow the same process (minus the ultronic cleaner) that I will have much better performance in my car? Thank You ever so much for this video walkthrough.

Would it have been better to put them through the ultrasonic cleaner to start with? Just curious..

Bro, touching the new screen filter with your grubby fingers and the bench then putting it in the injector, that was more junk then what's gonna get past your actual fuel filter and the fuel lines

Hello and thanks for the video.i have these same injectors on my golf and I can't find this kit can you help me out with a link or some local store I live in Los Angeles CA

Bosch or vdo injectors in vag cars like closed valve with leak clean not help its like 1 time use for 200 000 km example

Wife’s going to be mad ;) lol

Does refurbished injectors really work?

how come you left off the pintle caps ?

Thanks for the video!!!! What kind of cleaning solution did you use in the ultrasonic cleaner?

Ha ha.. If you use your wife's ultrasonic cleaner.. You can actually place your part in a container filled with whatever cleaner you want to use.. Then place your container of parts in the ultrasonic cleaner and fill the machine with water. The waves will pass through the container holding your greasy parts and clean them, without contaminating the water.