To watch same video in English click on below Link. • REF (Restricted Earth ...
Пікірлер: 331
@NiteshKumarElectrical5 жыл бұрын
Video of Difference between High Impedance & Low Impedance REF. kzfaq.info/get/bejne/l9aEY9CHqK-1l58.html हिंदी में😊
@chithiram81134 жыл бұрын
Sir tell me how to calculate stabilizing register value
@anmolmaharana57703 жыл бұрын
Sir in my gss 132/33kv trf 40mva is tripped on ref when heavy wind and rain occurs. I want to know the reason
@NiteshKumarElectrical3 жыл бұрын
Hi Anmol, Please check the REF CT wiring from Transformer Marshalling Box to Relay end. If rain start and REF operated means ..There might be some moisture issue or loose connection of CT wiring. You may take shutdown of transformer and check Turret CT secondary box of transformer from where CF wiring is taken up to marshalling box for CT ckt paralling. Note:-But before doing anything, discuss with your senior and then take any action. This is my personal opinion and suggestions based upon my experiences.
@anmolmaharana57703 жыл бұрын
@@NiteshKumarElectrical ok sir.. during rain condition other feeders tripped on O/C E/F. Is there any relation between these trips and ref?
@NiteshKumarElectrical3 жыл бұрын
@@anmolmaharana5770 No ! If other feeder is tripping due to rain means, there might be fault due to trees, punctured insulators and transient faults. But there is no relation between feeder tripping and REF. Concept & circuit is completely different. Yeah ! REF may trip due to inrush current during charging of transformer on no load.
@rajuperumandla67813 жыл бұрын
Nithish kumar jee you explained regarding REF protection superbly,and i hope everyone can under stood very easyly. Thank you for in-depth explanation sir jee
@amitprasad25882 жыл бұрын
Sir aapke jitna deeply or itne sahi dhang se kisi ko samjhate nahi dekha
@ManojKumar-rm7bn5 жыл бұрын
Ab tak hajaaro bndo ki vedios dekhi meine but you have a great quality of explain a subject
@NiteshKumarElectrical5 жыл бұрын
Thanks !!👍😊
@Vicky_paakad2 ай бұрын
Thanks sir, for explaining the REF protection, specially thanks for Rs, VDR calculations.
@rajuperumandla67813 жыл бұрын
Nithesh kumar jee you are explained very clearly where the REF Relay will tripped ,wether restricted zone or out of the zone . Thank you a lot.
@rajuperumandla67813 жыл бұрын
Nithesh sir jee mera ku to bahut acha laga apka lecture. I understood very clearly. I think this vedio can understood every technician below the engineer level also. Thank you sir jee.
@wasimsharif82423 жыл бұрын
Bahut kuch sikha hai bhai very nice explanation
@sreeramne5 жыл бұрын
VIDEO EXPLANATION WAS very good thanks please do continue to make more such kind of videos on different topics
@memanaspak21135 жыл бұрын
Keep it up...sir....clearly understand sir....with good graph and depth of knowledge...hats off....sir...
@ganeshsamal2906 Жыл бұрын
Sir transformer ki differential protection scheme pura ref wesa banaye sir please. Jitna protection hai sab banaiye. Ref pura samjh gaya sir 🙏thank you
@patelchirag95304 жыл бұрын
Keep it sir..it very detailed video that I only found nd superb explanation. Very detailed and in depth. We are respectful for your hardwork😊.
@patakotisrinivas19185 жыл бұрын
Superb explaination bro...U r efforts are really appreciable and commendable..thanks a lot for uploading this video..
@Alpha191033 жыл бұрын
Fan ho gaya bhai aapke explanation bka
@babjibabuseelam52184 жыл бұрын
Thank you very much sir, this video any one can understand ........like that u clearly explained.
@mythbuster19935 жыл бұрын
Very well explained... please upload more such practical videos
@muthuraman6093 Жыл бұрын
Excellent 👌 best wishes🎉 From Sweden
@petpujo22203 жыл бұрын
Very well discussion. I have to know much more things to know from you
@rakeshkumarrajan45493 жыл бұрын
Sir your explanation very simple & good. We learnt easy way of REF protection in power transformer. *Thanks a lot* 🙏🙏
@NiteshKumarElectrical3 жыл бұрын
Welcome Ji
@anilkumarshah4523 Жыл бұрын
you are great sir i watch your every video i have learned a lot thanks sir
@amrinkagzi92075 жыл бұрын
Very nice explaination..easily understood...Thank you sir..
@komalyadu77943 жыл бұрын
Very sharply explained sir I am understood so easily...thanks
@ramkharasane62194 жыл бұрын
Thank you so much sir for knowledge full video.....
@arvindkaushik50814 жыл бұрын
Really good #Nitesh ji
@MdArif-dk4ms2 жыл бұрын
sir really aap bahot achchhe se expalne karte hai chuki mai bahot logo ka video dekhta hu lekin kisi ko comment nahi karta pahli bar mai aap ko kar raha hu q ki aap bahot achchhe se samjhate hai
@NiteshKumarElectrical2 жыл бұрын
धन्यबाद भाई
@gaur20505 жыл бұрын
Sir, This type of practical course will help all Electrical Engineers. I am really keen to meet you personally as today your way of explanation has remembered me about my great college teacher also. Hats off to you sir.....
@NiteshKumarElectrical5 жыл бұрын
Thanks Gaurav !! For understanding well through my way of explanation. Mee too want to explain Practically with core theory and many electrical engineers are getting benefits. Such comments motivate me to find time out of my busy schedule to make & deliver great content to all.
@SumitKumar-pf9gr3 жыл бұрын
U really doing a good job... appreciated
@charinath54455 жыл бұрын
How the positions (primary) of the CTs to be arranged (P1 & P2) for both the line and neutral CTs?
@MRASIFRAZA15 жыл бұрын
Nitesh bhai आपने बहुत अच्छे से बताया है calculation... Keep it up..
@NiteshKumarElectrical5 жыл бұрын
धन्यवाद आसिफ भाई !!👍😊
@pjosephkumar5 жыл бұрын
Excellent Bro.. well explained.
@shivamtripathi22104 жыл бұрын
Excellent video on REF..Please also make a video on Transformer impedance, its importance and beneficial.
@panchalruchit67413 жыл бұрын
Really Help Full for me your teaching skill very Great... Thank you
@NiteshKumarElectrical3 жыл бұрын
Thanks. !👍
@Alwayslovingdude2 жыл бұрын
Very well explained..superb 👏
@rameshtripathy59785 жыл бұрын
Very good description !
@jhum9543 жыл бұрын
Sir Mera job jbsepl me lga hai as a testing engineer transmission substation me kya testing hota hai my frasher huu
@sohailjanjua1232 жыл бұрын
Hi, I like your lecture. Thanks
@Ashokkumar-je7kn2 жыл бұрын
Good afternoon sir well stitching
@devendraladava793 Жыл бұрын
Nice video..after so many year you cleared my concept about REF.. request to make video for differential protection same also.
@imadullah36194 жыл бұрын
Perfect Mr. Nitesh
@deepak15295 жыл бұрын
Brilliant sir ji...
@khanindrkaaushik67429 ай бұрын
Really good explanation 👍
@rambhoolsingh27544 жыл бұрын
Thanks for best knowledge .
@patelsatyam66494 жыл бұрын
Great video sir....Thanks for your knowledge sharing
@ZahidHussain-wk1zl5 жыл бұрын
Well explained... Keep sharing your experiences
@NiteshKumarElectrical5 жыл бұрын
Thanks !👍
@pitamber88795 жыл бұрын
👌👌sir make video on every equipments installed in 400kv substation.
@ambikaraja9656 Жыл бұрын
Superb explanation.
@vijaybhagat42454 жыл бұрын
Really very very informative and well explained video Sirji
@NiteshKumarElectrical4 жыл бұрын
Thank You..!👍💐
@ashishdixit70504 жыл бұрын
Nice explanation
@Sarojsandarbh5 жыл бұрын
Well done Very nice sir....
@akashsenta3601 Жыл бұрын
Respected Sir My trasformer REF protection Neutral CT 5P15 and phase CT PS class At a time near fault REF protection is operated. Can different class CT use for fault feeding operated.
@tufailalam64385 жыл бұрын
Sir. If Vsp>2kv..what should be the value of VDR.
@ASHISHSHARMA-gz7yp2 жыл бұрын
What are the repurcusions of not grounding neutral of Hv side of PTR in star star configuration ptr. As it is tripping line with neutral grounding .
@maroofchoudhary22963 жыл бұрын
Very very good explanation
@alhaseef82689 ай бұрын
Hi nithish your video is very useful, please advise me as we have stabilising resistor in series with relay and the settings we kept in very low value. When the fault happens how the resistor will allow small current to pass through to the relay. Actually the resistor would have its own resistance to restrict the current. Please advise
@RK205055 жыл бұрын
what is the your software used for explanation
@ramrah47344 жыл бұрын
Superb explanation sir
@neerajpiplani1854 жыл бұрын
In one of our substation whenever the 66 kv voltage is on higher side may be greater than 70 kv and if power transformer after maintenance is switched On it trips with REF indication .Could you please explain the reason for same
@ASIFKHAN-ui7jp3 жыл бұрын
GREAT EXPLANATION THANKS A LOT
@ManojkumarSahoo_electrical3 жыл бұрын
Sir, How to calculate the power rating (Wattage) of stabilizing Resistor for REF relay.
@rakeshgehlot95905 жыл бұрын
Very nice explanation sir thank u
@kapilkanzariya30875 жыл бұрын
which class ct used in ref
@salimmalek99922 жыл бұрын
Very Good teaching sir
@kulkarnir934 жыл бұрын
Great sir.I like ur video.I want to know about Differential & bias current in differential protection. Thanks
@md.uzzalmiah6444 жыл бұрын
Thank you very much for a good lecture. Please do u have any lecture about NGR in generator? How connected with parallel generator and how does calculated resistance valu? Please give me link about its.
@sunilkumarmishra3323 жыл бұрын
Very informative video sir. Please make video on Insulation Monitering device & their setting.
@PANKAJKUMAR-kv2eh5 жыл бұрын
The influence of good teacher can never be erased . Thanks a lot Sir. You are inspiration for many people..
@NiteshKumarElectrical5 жыл бұрын
Thanks for your feedback ! Such comments really motivate me to make good things for all. I find very less time to make videos due to my job but even though I find time. If people's are getting benefits from my videos then I think so that my labour is successful.
@PANKAJKUMAR-kv2eh5 жыл бұрын
You deserve it Sir. I am proud to be your youtuber student. Your video helps me to clear my concepts and to gain practical knowledge...You have a done great work for the nation and youths in improving their practical skills. You can easily achieve theoretical knowledge by books but for practical knowledge everyone needs a Tuitor like you...Jai Hind
@NiteshKumarElectrical5 жыл бұрын
@@PANKAJKUMAR-kv2eh जय हिंद, जय भारत। !!👍
@ksroat61284 жыл бұрын
Very good sir
@wasimsharif82423 жыл бұрын
Best explanation bro
@yadavparvind6710 Жыл бұрын
Very good video sir..
@realityofworld17865 жыл бұрын
Bohot awla sir
@machhivivek41673 жыл бұрын
Excellent sir..
@RakeshKumar-bt3nr4 жыл бұрын
Nice explained !!
@debduttbhattachargee18143 жыл бұрын
The current flows in secondary of CT Opposite to primary due to faradays law which will oppose the change in EMF. Please include. Nicely explained.
@sapannayak23685 жыл бұрын
Nice explanation brother
@roy65163 жыл бұрын
Why ct impedance become low after saturation.. even though current is also low
@sameermd99565 жыл бұрын
Excellent sir 👌👌👌
@cookwithkhushboosingh94665 жыл бұрын
Wonderful explanation 👍
@powercircuits40134 жыл бұрын
Nice
@drsimx37295 жыл бұрын
good territorial thanks a lot sir
@Manish-cs9tr3 жыл бұрын
Super sir......
@subratlipun40835 жыл бұрын
Generator olta ghumega ta voltage produce hoga ki nehi.....aur kese
@mksingh01215 жыл бұрын
You are so good sir more video
@sandeeptiwari-ti8wt4 жыл бұрын
good explanation sir make note on differential protection of single phase transformer.
@asheshchatterjee33945 жыл бұрын
Sir in case of through fault why not current in the phase CT be in the reverse direction. Because current will flow from supply direction...
@pradeepsingh3504 жыл бұрын
Very good explanation Sir..kindly make a video on power transformer benifit of star to star windings and other combination...deta to star
@vijaymaurya90705 жыл бұрын
Very very nice sir keep it sir
@arabindabehura41815 жыл бұрын
Tremendious sir.
@Ajay_44885 жыл бұрын
very true and related to the real eg. nice keep it up sirji..can you have any idea of cbct protection with 3 wire inside cbct and N wire outside cbct..and another all 4 wire inside cbct..so how D2EFR1 relay will work..please share your valuable knowledge ..
@mohanguguloth99924 жыл бұрын
Bhai a topic kounsa book may study Kiya please suggest me
@souravbose81154 жыл бұрын
Sir, ek doubt hai. Why would I1 flow from the load to the fault? Shouldn't the current of B- phase flow directly to earth at the fault and come back through the neutral and not flow through the phase C.T at all ideally? Aur Normal condition me kya hoga? tab to B phase ka C.T full phase current sense karega aur neutral ka c.T ideally koi current sense nehi karega. Tab kyu trip nehi hoga? Please explain as early as possible. I will be grateful.
@tventertainment58279 ай бұрын
Drawing k liye kon s software use kiya h apne??
@gaurav17444 жыл бұрын
Sir I'm electrical engineering student and want to have internship in relay company like ashida , how do i apply . Please help me out I'm egar to know more about relays
@soumyajitsundarray43164 жыл бұрын
Dear Nitesh Can you will made a video on centralized busbar protection vs a decentralized busbar protection system
@gangadhardas56223 жыл бұрын
Super fainstatic Sir👍👍👍👍👍👍,,
@anandbhadang2913 жыл бұрын
Nice one
@saakchannel33514 жыл бұрын
Excellent way of teaching. .Learned a lot from your video thanks to a lot dear.
@NiteshKumarElectrical4 жыл бұрын
Thanks !😊💐💐
@saakchannel33514 жыл бұрын
@@NiteshKumarElectrical If possible please upload videos of relays testing for feeder protection, differcial protection, imedence protection, etc.
@umeshshrivastava67663 ай бұрын
Where we need to install REF in trf incomer In LT panel or outgoing in HT panel. Can we install in both panel
@sakshimishra40234 жыл бұрын
How to decide rating of metrocil
@shareeffishingtasteydishin4915 жыл бұрын
Nice explain...
@adithihomeplant36613 жыл бұрын
Super video sir.r u doing any video TNC switch? Pls inform me
@mahingajjar60594 жыл бұрын
excellent sir, pls make vedio on generator protection relay