Stainless Steel Hose Clamp (Jubilee Clip) actually is much better & safer than factory sealed Ferrule. A ferrule is a round metal sleeve that's permanently swaged, or clamped, on to the end of a hose during the manufacturing process to prevent inexperienced people to adjust it. It's usually made of a zinc alloy. You will find Ferrule on gas hoses in most of western countries because of Gov regulations but most of the world uses Jubilee Clip on gas hoses. Furthermore, as per video (time 8:22) I have checked for gas leaks with the soapy water and there wasn't any leak. Hose I have on the video is made to transfer gas from one cylinder to another, not for permanent use. Thanks for watching and your comments

My Hubby worked in the steel furnaces of Europe and UK using a high pressure oxygen lances often, S/S jubilee clips used everywhere never failed once he says.

When you're using a gas bottle as a work bench, its surprising you got the chance to upload the video

All you do when you have cut the bit of hose off is apply some heat (not attached to gas bottle) and the rubber becomes soft and clamp pulls off easily with pliers. Heat does not bother the brass at all.

Nice one Aussie. Sometimes a bit of knowledge is a dangerous thing. I have seen Jubilee clips come loose at pressures as low as 6 bar. Propane tanks are ~10bar. Whats happening in the tank is that the propane is a liquid under that pressure. With gas sitting at the top of that. As the gas is used/released the temp drops. Thats why the bottle gets cold like that. Naturally you want to transfer as much liquid as possible to the bottle as transferring the gas is going to take a very long time. Before starting. Make sure the empty bottle is completely empty. Then start the process with the full bottle upside down. This will mean taht only the liquid is being transferred and the process will be very quick. Note. You can buy the crimp type hose clamps at bunnings. They are cheap and you will get a much better hold on the hose.

The bleeder that you opened with red screwdriver, during the refilling process the bleeder remains open ? Or u just quickly open the bleeder in the beginning and then close it off during the refill process?

Well... if you watch the video and read all the comments you will have been exposed to all the considerations on how to do it properly and as safe as possible in your own backyard. What you do with that new knowledge is your responsibility. I learnt a lot actually.

I can’t stop laughing at videos like this 🤣

Good video. I enjoyed it. Thanks.

Brilliant thank you so much for sharing this. Loved watching you 3 take care stay safe 😘😘😘

Cheers for the video. I was led to believe that a gas bottle shouldn't be turned upside down??

Ideally , keep the big bottle suspended upside down and above the small cylinder being filled so you get liquid gas rather than vapour. Cheers and good vid

How to buy the pipe

Thanks for the how to! It works a treat!

thanks heaps very helpful, cheers

I love how he's got an air compressor, but he had to bolt the hose to his door frame 😂

thanks for that and turning the feed bottle upside down is correct and leave the bleed valve open till receive bottle is full you should see white gas at the exhaust port, now close bleed valve and feed and receiver valves, done.

When you transfer the gas from a big container to a small one does the pressure of it increase?

Isn't it dangerous to create a spark near or close to the inlet/outlet valve? By hitting any metal can create a spark.

Easy done .

Excellent video

I kept thinking any second the first aid kit would have to be used. Nerve racking.

Amazing how clumsy this person is.

I'm amazed no one has mentioned how dangerous this method is. A propane bottle should only be filled to 80% to allow for expansion. If you fill a bottle to the top on a cold day and leave it out in the sun it is probable that the safety valve will blow resulting in a gas escape. If you must fill like this please weigh the empty bottle first, add the lpg whilst weighing as it fills. There should be a nett weight stamped on the bottle. This is the weight of the contents when full. Add the two weights together for your target weight. To stay on the safe side I'd only fill to say 60/70% before stopping.

The supply tank had to be turned upside down because liquid fills the other and not gas. This is dangerous. The valve can freeze. The hose can freeze. Not recommended

hello from iraq with you well done

Mate, I can't believe you don't have a vice, and have to use a G cramp on your house wall to secure the hose... It doesn't install a huge amount of confidence in your method.. also you don't use any kind of spanner of wrench to tighten the joints. Unberfuckingbelievable.

So,if you watch an official video teaching the correct (safe) way to decant. you'll see the same basic procedure. However use spanner to tighten fittings. EARTH your self and BOTH bottles.

Need to get the liquid in there and be sure to fill by weight

WHAT WAS TE PURPOSE OF THE BREATHER, COULD IT NOT RELEASE ALL THE GAS THAT YOU HAD FILLED INTO THE SMALL BOTTLE?

How much prise 4 kg ⛽️

place the small gas on a scale, stop it at 2kg hahahahah

I need some help how to bottle the methane gas

I personally would not use a hammer and screw driver on a propane tank to remove fitting

Good god. Did anyone become concerned with the use of a screwdriver as a pry bar, & cringe @ the use of the utility knife? I was waiting for the slip.

You didn't have to cut the hose Use a hand file to file down the retaining ring

Well done. See all the "safety" experts putting in their 2cents worth.

If only you had shopped at *Blue LPG* and all the hose mucking around would not have been necessary.....

His Funeral was on Friday.

You can see the liquid propane transfer here: kzfaq.info/get/bejne/ptelZNt3kqfDnmg.html

LPG car kit

PLEASE ALL WATCHERS, YOU MUST ONLY FILL TO 80% BECAUSE THE GAS EXPANDS MORE THAN 80% WILL BE RISK OF EXPLOSION, SO WHEN FILLING ALWAYS WEIGH THE BOTTLE

I wouldn't trust that single worm clamp.

When finished sit back relax and light a cigarette 💥💤

I wonder if this guy is still alive

Holy shit this is sketchy.

A barb to 3/8" fitting is easily obtained - why butcher two perfectly good hoses with crimped ends? start with a hose with the correct fittings. And a laughable alternative to a vise.

Are you a person or a computer lol

That gas bottle is almost ten years out of date ! Scary stuff.

You dont have tools my friend

R u still alive....?

NO YOU DO NOT NEED TO DO THIS ! - and could be illegal !

This is a How "NOT TO" video.

Absurd, dangerous and unacceptable "advice" videos for people unable to understand what is to work with highly pressurised inflammable gas

This is the most inept engineering that i've seen in a long time. Do you really have so few tools? Why didn't you explain why you used the bleed valve and inverted the source tank? English may not be your first language, but do you really need a voice synthesizer?