Registration using Ternes Burton pins and tabs Part 2

Рет қаралды 4,579

Colin Blanchard

3 жыл бұрын

Colin Blanchard shows how he registers a combined linocut and screen print. Part 2 of 2 - Screenprinting

Пікірлер: 25

@marionwigzell7334 6 ай бұрын

A beautiful print (-: Marion 🎉

@catharina7613 Жыл бұрын

this is fantastic. thank you so much for sharing

@chrisp7799 8 ай бұрын

Would love a you tube explaining and showing how to make the adjustable screen holder which looks great

@antoniorusalba7670 Жыл бұрын

Gracias, maestro

@coburnlowman Жыл бұрын

I have wandered for years how this was done. Ill never look at old prints the same again

@suewelfare9154 3 жыл бұрын

Genius - watching this a whole *pile* of pennies dropped! Thank you xx

@anneclappison6035 2 жыл бұрын

Wonderful tutorial. Beautiful print. Many thanks for sharing.

@bravespears Жыл бұрын

Genius ❤

@annebeidler8782 2 жыл бұрын

remarkable! and so well presented!! thank you

@JaneCizynski Жыл бұрын

That's just incredible ! What patience !. You do beautiful work ! thanks for sharing

@Vgudorf Жыл бұрын

Fantastic! So helpful. Thank you, Colin!

@sylviendresen6243 3 жыл бұрын

Thank you so much for these inspiring lessons!

@suewelfare9154 3 жыл бұрын

And the print is exquisite

@bobbinsandbowsofbare5231 2 жыл бұрын

Thank you, great video, beautiful work

@printinglady 2 жыл бұрын

Wonderfully clear, lovely prints

@Lauragld 2 жыл бұрын

Wonderful!!!! Thanks so much for sharing this process :)

@SuzeJS Жыл бұрын

Thank you so much. This was such a clear and helpful video. :)

@davidjames2145 Жыл бұрын

Jaw-drop masterclass.

@marilynbrack3803 3 жыл бұрын

Fantastic video, clearly spoken easy to follow steps with good tips along the way. Colin for that print did you use 9 silkscreens to print the transparent colours to the linocut print?

@colinblanchard 3 жыл бұрын

Thank you very much Marilyn. It was difficult to keep the video concentrating on the registration process and it not become a screenprinting video! I made four fresh stencils, but three of them were used several times in a reduction method. i.e. palest colour/tone through all of the stencil; paint out palest areas with filler; print the next colour/tone: paint out that colour....and so on.

@marilynbrack3803 3 жыл бұрын

@@colinblanchard of course that was a more economical way to go regarding use of screens. I must look into how to clean the Lascaux filler off the screen. Any tips or just follow product instructions?

@colinblanchard 3 жыл бұрын

@@marilynbrack3803 A pressure washer is essential. Strip as soon as possible; if left for any length of time it’s even more difficult. The stripper they sell is only strong detergent and Mystrol will work. .....eventually. I work outside in a proper washout booth with a deep earth soak away drain system and use a strong organic solvent - good old fashioned stinky screenwash . Brush on both sides generously, leave to soak for 10 mins horizontally, mask and goggles on, pressure wash off. Repeat. Degrease.

@marilynbrack3803 3 жыл бұрын

@@colinblanchard Thank you so much for this information Colin. Very helpful.