By far the best "factory" remove and install video out there. Thank you for sharing...

Tip: You can avoid breaking the black plastic clips if you lift up firmly on the fender flare as you pull it away from the Jeep. The plastic fender flare will pull out of the clips and leave them attached to the metal fender wall of the Jeep. Use needle nose pliers to reach behind the metal fender wall and pinch the tabs on the clips so you can pull them out. You can then reuse them. I did this without breaking a single clip.

Excellent video...very informative. Your Jeep looks a thousand times better.

Great video. I didn't know I could get the kit from Rugged Ridge but now I'm going to reattach my fenders. They have been loose for a while now. Thanks for all the info.

All you need is a small punch tool to push the center of the plastic ruvet. Also since you're separating the inner liner from the fender flare you can do that before you remove the fender flare from the jeep and save all the clips. I didn't break one single clip when using the proper body clip removal tool. I don't understand why everyone thinks you have to yank the whole fender flare off with brute force.

Great video. Very helpful. Only thing I would recommend, is to have someone else hold your camera for close-up shots when you're not able to hold the camera.

Great video. Just did this. You can get the front ones off by pulling up and out with out breaking all the connectors (I'd still use new ones though). The rear it's near impossible to lift up enough so I had to use brute force and it feels like the fenders will almost break ;-0. Amazon has connectors for much cheaper than other places but I needed 2 sets...cost about $27 for two sets. I also added an extra "christmas tree" connector at the very front end of the front bumpers as there is no connector there. Weird.

Thank you for your jeep fender removal and replacement video. Thanks to you and thevntire weekend I managed to change out all 4 on my 2008 wrangler unlimited. THANKYOU!!

Thank you for an excellent video. It is exactly what I needed. Much different from the older model Jeeps. Carry On.

This video is for the fender flares, not the fenders as the title states. Good video, just not for the actual fenders.

Heck yeah! Thank you! Short and sweet and accurate

Had no problem taking the old flares off... it was in trying to resinstall them that I had an issue. No matter how hard I push, the pins will not re-engage into the body sheet metal. I think I will try putting the flare on first and then mounting the inner fenders as the final step.

Thanks for doing this video, very helpful info. Jeep looks very sharp with the painted flares. Planning on doing the same! 👍

Great presentation and recording

Thanks for sharing the clip info. I will go to Amazon and get some

Thanks this vid helped a lot in replacing my finders

Thank you for taking the time to make this helpful video.

Awesome! I appreciate you sharing this. It would have taken me much longer to do this as i would have missed a few things.

Best oem jk fender flares video!!! Thanks for sharing

I agree, getting ready to tear into it. lol thanks for the great content my friend!

Nice work, thanks!

This video does not remove the fenders, only the fender flares and linings.

ok your spot on. thanks for the info

Great video - exactly what I am doing - thanks

Thanks great video super helpful!

Great video - exactly what I am doing thank you

You did not remove and reinstall the fenders. You removed and reinstalled the fender flares.

Great video. What about that very front place for a clip where it doesn’t have a slot to put the clip into? It’s at the very front of the front fender.

All you had to do is take a heat gun. It brings the oil to the top and they will look brand new. And you can paint them if you use sealer first.

Looks way better

Can I use the same round flat all around? I see you used different ones for different spots.

What is the name of the tool used to push in those pins ? I think you said you bought it at harbor freight ? Awesome video. Much better video that folks at Extreme Terrain put out.

excellent, I kinda missed the rivet gun and purpose

Another time and money saver if you don't want to paint them is to use a heat gun. Brings them back to new in seconds.

Nice jeep

Did you say Go back on the CAR😑 You can Also go up Behind the fender Clips with a pair of needlenose pliers squeeze behind the clip, Then the fenders just pull off without breaking the clip 😉 your welcome 😁👍

Where did you get both the new painted fenders and the clip replacement kit?

Do you absolutely have to take out the inner liner?

I'm doing the rear fender flares but finding it difficult to put new flare on where the rectangular clips just go right in the holes. They keep falling out of the wheelwell liner. How did you line up and snap in so easy?

50 bucks for the plastic clips? Sheeeeeeeeeesh. I bought a "universal" clip kit on Amazon for basically nothing

Does this Jeep have a lift on it trying to find out what a non lifted Jeep looks like with aftermarket flares.

Hmm... everybody's listing their fender flare videos as fenders

what its the name of the tool you use for the large taps for the fender to the liner you know the larges taps around the fender

Do you have to get them painted or can you order them the correct color?

them are fender flars NOT fenders

Do you have the part number for the bag of clips that holds the fender to the body?

Not very help can't see what your doing with the fender in the way

Question! Can i reinstall my OEM fenders without the liner?

What kind of screws did you used? Min 11:03

Do you have red covers on your shocks?

Where can I find them fender flares please?

intro WAY too loud

Thanks this vid helped a lot in replacing my finders